Solder Paste Inspection
assures volume and area of paste application.
See Also: Solder Paste, Solder Paste Measurement, 3D Solder Paste Inspection
-
Product
Inspection System for Die Casting
X-eye 7000BS
-
Appropriate for medium•large size component inspection and detecting surface structure and defects(inside voids and cracks etc).Due to high-energy, high-power Micro-focus X-ray Open Tube, maintenance cost's reduced significantly and enables long-term use with only replacing consumables.Customization is available with selecting main parts by customers depends on their needs for size and material.
-
-
Product
Electronic Inspection Systems
-
Intego's knowhow even makes it possible to identify challenging defects that may be located under the surface. One system is the inspection of chips by means of lock-in thermography, which visually represents the IR radiation intensity signal of electronics. Special lasers and flash lamps generate a very short heat impulse (10 ms) on the chip, which generates a measurable heat flow. In most cases, a resolution of < 1 μm can be achieved.
-
Product
Automated X-ray Inspection (AXI)
-
Automated X-ray inspection (AXI) is a testing approach based on the same principles as automated optical inspection (AOI). Instead of cameras, X-rays are used to automatically inspect features.
-
Product
Visual Inspection Software
AdVISE
-
R&S®AdVISE visual inspection software automates the process of visually monitoring an equipment under test (EUT) during a test sequence. This eliminates human inattention, ensures reproducible results and simplifies the test documentation. A typical application is EMS testing with R&S®EMC32 and R&S®ELEKTRA test software.
-
Product
Inspects MEMS and Wafer Level Devices
NorCom 2020-WL
-
The NorCom 2020-WL is specifically designed for wafer-level inspection and leak tests up to 1000 devices per cycle. The system can inspect up to an 8” wafer on or off a saw frame. It is designed to test MEMS and other wafer level devices that have a cavity.
-
Product
Inspect & Explore Indoor and Confined Spaces
ELIOS
-
Discover the first collision-tolerant drone, designed for the inspection and exploration of the most inaccessible places. Allowing for the first time to fly in complex, cluttered or indoor spaces, Elios unleashes the potential of UAVs in numerous applications where their use was previously too dangerous or simply impossible.
-
Product
Post Wire and Die Bond Inspection Machine
IV-E1700
-
IV-E1700 is a post wire and die bond inspection machine that is known for having a proven, effective and patented 2D+3D Inspection system. This product is best used to weed out defects with data collection for process improvement and reports for SPC quality Control.
-
Product
Thickness and Flaw Inspection
MultiScan MS5800
-
Eddy current testing is a noncontact method used to inspect nonferromagnetic tubing. This technique is suitable for detecting and sizing metal discontinuities such as corrosion, erosion, wear, pitting, baffle cuts, wall loss, and cracks in nonferrous materials.
-
Product
01 With Soldering Eyelets | 12 Positions | M10 | 2 Wafers
01-2xxx-00/30xx-12-N
-
Multi wafer compact selector with 30° detent angle, 6 mm shaft diameter, 25'000 switching cycles and with up to 6 Ncm switching torque
-
Product
Tracing-Type Non-Contact Inspection System For LCD/STN/Touch Panel/FPC
TTS
-
*"Probe + Non-Contact Sensor" enables to delect SHORT after sticking LCD*No Fixture in LCD Inspection*Applicable to FPC Inspection
-
Product
Hi-Definition Video Inspection Station
VIS800
-
Video Inspection Stations are available with?or without on-screen measurement capabilities?and offer?an excellent way to evaluate or test small works or items in?difficult to access locations.? As todays electronic and mechanical systems keep getting smaller, it becomes impossible to test or measure these products with traditional methods. For many applications, from development to production testing, video based inspection can help maintain quality control. Many of these systems are used in labs for development or used in production for testing production samples.
-
Product
GPR System for Concrete Inspection
StructureScan™ Mini
-
Geophysical Survey Systems, Inc.
The StructureScan Mini safely locates metallic and non-metallic targets within concrete structures up to a depth of 20 inches. The system incorporates an auto target feature that marks the detection of features of interest. This function also estimates the depth of targets and automatically adjusts the depth scale.
-
Product
WiFi Inspection Cameras
-
WiFi Inspection Cameras generates a local WiFi hotspot (without Internet access) through which video clips and still photos of hard-to-reach or hard-to-see areas or equipment captured by the probe camera can be sent to an app-enabled smartphone or tablet for viewing and sharing. Free apps for iOS devices (iPhones or iPads) and Android devices are available from the iTunes App Store and Google Play Store, respectively. The three WiFi cameras differ in probe length, camera lighting and grip style.
-
Product
Industrial CT X-Ray Inspection System
X25
-
The X25 is quite possibly the most conveniently sized industrial CT system on the market. The system offers all of the same features as the larger systems while still maintaining the ability to fit through a standard interior door. The X25 is well suited for small to medium sized objects.
-
Product
Magnetic Particle Inspection
-
Magnetic Particle InspectionMagnaflux Magnetic Particles are used for magnetic particle inspection method in the detection of SURFACE and SUBSURFACE indications in FERROUS materials.
-
Product
SparkFun Solder-able Breadboard
Large
-
This is the Large SparkFun Solder-able Breadboard. A bare PCB that is the exact size as our full-size breadboard with the same connections to pins and power rails. This board is especially useful for preserving a prototype or experiment you just created on a solderless breadboard by soldering all the pieces in place.
-
Product
Reflow / Wave Solder Process Dashboard
Vantage
-
Real-time dashboard for all reflow ovens in the factory. Accessible from all authorized PCs and mobile devices anywhere. KIC Vantage is a factory level Industry 4.0 smart factory system for reflow and cure data management and analytics. It truly does give you the best vantage, gaining insight into your reflow and cure processes throughout the factory.
-
Product
Defect Inspection and Review
-
KLA’s defect inspection and review systems cover the full range of yield applications within the chip and wafer manufacturing environments, including incoming process tool qualification, wafer qualification, research and development, and tool, process and line monitoring. Patterned and unpatterned wafer defect inspection and review systems find, identify and classify particles and pattern defects on the front surface, back surface and edge of the wafer. This information allows engineers to detect, resolve and monitor critical yield excursions, resulting in faster yield ramp and higher production yield.
-
Product
Hi-Definition Video Inspection Station with Measuring
VIS810
-
Video Inspection Stations are available with?or without on-screen measurement capabilities?and offer?an excellent way to evaluate or test small works or items in?difficult to access locations.? As todays electronic and mechanical systems keep getting smaller, it becomes impossible to test or measure these products with traditional methods. For many applications, from development to production testing, video based inspection can help maintain quality control. Many of these systems are used in labs for development or used in production for testing production samples.
-
Product
Inspection System for high-power precise 3D X-ray CT
X-eye PCT225
-
Inspection System for 3D X-ray CT able to analyze defected area precisely by precise movement of axis with high polished Anti-vibration table. High-power X-ray Tube of max. 450kV and large area Flat Panel Detector of max.16 inches can be installed depending on the sample. Customized 3D CT equipment is available with selecting main parts by customers depends on their needs for size and material.
-
Product
Inspection
-
A complete line of testing instruments for inspection laboratories is available from our Petrolab group. We specialize in instruments for vapor pressure, flashpoint, distillation, and color as well as equipment for hundreds of other ASTM, ISO, and DIN testing procedures. Below are a handful of items we offer.
-
Product
Ground Resistance Inspection Box
-
AllWin Instrument Science and Technology Co., Ltd.
Check the ground resistance tester each time prior to start work everyday morning and do some relevant records.
-
Product
Manual Spin Rotary Table for Optimal Circular Geometry (TIR) Inspection
TruMotion
-
Rotary Precision Instruments UK Ltd
Inspect circular components in a shop floor environment whilst maintaining world class accuracies more commonly seen in the standards laboratory.
-
Product
A Compact X-ray Inspection System, The MedaScope™ Desktop
-
A compact X-ray machine weighing only 55 pounds, the MedaScope Desktop is easy to carry and can be set up rapidly. Glenbrook’s MedaScope Desktop is a portable, compact manual system for real-time, magnified x-ray screening of packaged devices including medical devices, electronics, and cables.
-
Product
200-480 degree Soldering Station
SM-936B
-
* Temperature range 200C-600C (392F-896F).* Ceramic heating element and sensor insures rapid heat-uptemperature.* Celsius or Farenheit temperature setting.* Temmperature adjusted by simply turning the dial.* Wide selection of tips available.
-
Product
Replacement Solder tip lead set for D420/D620
Dx20-SI
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
-
Product
Mobile ASA-Livestream Data Node for Main Inspection
CONNECT CUBE V3 | VP 185076
-
Maschinenbau Haldenwang GmbH & Co. KG.
The mobile data node is the right tool for quick and digital diagnosis of the brake system as well as for routine testing and calibration of all ASA livestream-capable brake testers. The plug & play solution can also be used for modern routine testing and calibration of brake test stands.
-
Product
GPR System for Concrete Inspection
StructureScan Mini XT
-
Geophysical Survey Systems, Inc.
The StructureScan Mini XT is GSSI’s newest generation of our very popular all-in-one GPR systems. The StructureScan Mini XT offers a 2.7 GHz antenna for superior target resolution and can reach depths of 20 inches (50 cm). Ideal for locating rebar, conduits, post-tension cables, voids, and real time determination of concrete slab thickness.
