UL
-
Product
Smoke Detection Sensor - UL Approved, TAA Compliant
ENVIROMUX-SDS-TAA
-
For warning of smoke. Photoelectric smoke detector. Built-in 135° F (57° C) thermal heat sensor. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Voltage Supply: 8-35VDC. Current Consumption: 200uA. Alarm Output: Relay (NO). Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: UL. TAA compliant.
-
Product
UL 1410 Coin Probe
CX-121
-
Shenzhen Chuangxin Instruments Co., Ltd.
Four probes in one! Used to determine accessibility to shock hazards in many household and audio/video products, including Standards UL 1410 and UL 6500. Made entirely of nickel-plated steel.
-
Product
CB-37F-HVD, 37-pin ScrewTerminal Blk, UL rec.150V CAT II, Din Rail
779491-01
-
37-Pin Female D-SUB to 37-Pin Female Screw Terminal, High Voltage Horizontal DIN Rail Terminal Block - The CB-37F-HVD features screw terminal connectivity for up to 37 I/O signals, 12 to 30 AWG. It has a female 37-pin D-SUB connector for connectivity to C Series I/O Modules and … data acquisition devices. The CB-37F-VHD is UL recognized. You can use the CB-37F-VHD with low-voltage or high-voltage products up to 150 V.
-
Product
NEMA 250 and UL 50 Testing
-
NEMA and UL 50 Enclosure Type Ratings are accepted all over North America and referenced in the National Electric Code, NFPA, UL standards, and other product safety standards. F2 Labs can assist you with NEMA 250 testing and UL 50 testing, and the proper certifications for your products.
-
Product
Usability Testing
-
Underwriters Laboratories Inc.
Ascertaining the safety of medical devices obviously includes the human factor – the people who are using the device must be able to do so safely and effectively. UL''''s usability testing services are aimed at achieving compliance with regulatory requirements, reducing medical device use error, helping manufacturers create user-friendly devices, and reducing training costs.
-
Product
1U Type Power Supply; ATX 200W
PS200-1U
-
*Input Range: 90 ~ 264VAC Full Range*Output Voltage:**+5V, 17A**+3.3V, 14A**+12V1, 6A**+12V2, 12A**-12V, 0.8A**+5Vsb, 2A*MTBF(hours): At 25°C, 100,000h*Safety: CB, TUV, CE, FCC, C-TICK, CUL, UL, CCC*Dimensions: 150 x 81.5 x 40.5 mm*Compatible with Axiomtek products: AX61120/AX60530
-
Product
Speed Switch
UDS1000
-
Features• Works with remote / external quadrature pulse frequency outputsensor / incremental encoder (NPN or PNP)• DPDT relay changes state when shaft direction reverses• Reverse-over-speed setpoint adjustment from 0.5-5,000 rpm• Relay resets when reverse motion stops• 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options• Explosion proof/NEMA 4X housing• UL Listed Class I, Div I (C, D) Class II, Div I (E, F, G)
-
Product
Pressure Transmitters
-
Explosion-proof pressure transmitter is approved for use in hazardous locations per CSA Standard 30 and UL Standard 1203 for Class 1, Division 1 and Division 2 hazardous locations. Wetted parts are all 316L Stainless Steel (50 up to 10000 PSIG), 17-4PH (15000 & 20000 PSIG) for compatibility with a variety of media. Wetted materials and construction comply with the NACE MR0175 Standard. The KP46 Series explosion-proof pressure transmitter's fitting and sensing diaphragm are machined out of a single piece of material, so there are no welds, seams or O-ring seals, resulting in excellent long-term performance and stability. The case is factory sealed, making this pressure transmitter very rugged with excellent shock and vibration resistance.
-
Product
Electrical Product Safety Testing
-
We specialize in pre-certification evaluation, CE marking self-declaration testing, UL / CSA / TUV certification/verification testing. Other agency witness testing may be arranged upon request. CKC’s, and our partners, are equipped to test to a wide array of products including information technology, audio/video, test and measurement, medical and industrial.
-
Product
Wound Component EST Analyzer
19036
-
Chroma Systems Solutions, Inc.
The industry’s first Wound Component Electrical Safety Test (EST) Analyzer that combines impulse winding, AC/DC hipot, insulation resistance and DC resistance test measurement functions. Chroma’s 19036 Wound Component EST Analyzer has 5kVac/ 6kVdc high voltage output, 5kV insulation resistance, 6kV layer short impulse voltage and 4-wire DC resistance measurement with a maximum output of up to 40 channels. Capable of outputting and measuring AC100mA/DC 20mA, Chroma’s 19036 is suitable for testing to high power motor standards such as UL 1004-1.
-
Product
General Power Relays
-
Panasonic Industrial Devices Sales Company of America
2A and greater load rating in Polarized, Non-Polarized, High Capacity DC, General Purpose, and Safety configurations. UL, CSA, C-UL, TUV, VDE, and SEMKO certifications.
-
Product
Speed Sensor Intrinsically Safe
ST420
-
Features• 2-wire, loop-powered 4-20 mA analog output• No user calibration – works right out of the box• Standard and custom measurement ranges available• Reverse-wiring protected• Works with Electro-Sensors magnetic pulser discs / wrapsRugged stainless steel M18x1 housing; UL listed, Intrinsically Safe (IS); Class I, Div I (C, D) Class II, Div I (E, F, G)
-
Product
Speed Switch
SCP1000/SCP2000
-
Features• Internal sensor• Over-or under-speed config., 1-990 rpm• 1 DPDT relay output (SCP1000), 2 SPDT relay outputs (SCP2000)• Built-in start delay• Dial-in calibration does not require power• 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options• Works with Electro-Sensors magnetic pulser discs / wraps• Explosion proof housing• UL Listed Class I, Div I (C, D) Class II, Div I (E, F, G)
-
Product
[5kV AC] Hipot Tester, Rise/Fall-Time Control Function Equipped
TOS5200
-
TOS5200 is designed for AC Hipot Test with 500 VA capacity and 200 mA short circuit current output capability. Equipped with the PWM amplifier, the TOS5200 can provide a stable & reliable output without being affected by ACpower line. Therefore, it is a perfect solution for electronic equipment or devices complied to IEC, EN, UL, VDE andJIS etc. requirement.As TOS5200 covers most of features of our upper class model for AC Hipot Test, it achieves thesuperb cost / performance ratio for those who need 200 VA or 500 VA capacity, or both. Also, as it equips the Interlockfunction together with other safety features, operator can carry out the test with higher current value in safe.
-
Product
110-460V AC/DC 4-way Circuit Tester
1962
-
Peaceful Thriving Enterprise Co Ltd
*With UL and cUL Approval.*Bright neon AC/DC indicator.*Unique features with convenient pocket up.*Check voltage on 110V, 220V, 277V and 460V AC/DC.*Individual indicator for each voltage range assures reliability.*Reinforced casing and twin flexible test leads store in housing.
-
Product
3-Phase AC Voltage Transducer
ENVIROMUX-PT3-600
-
Monitors and reports voltage of any 3 phase circuit. Remotely detect blown fuses or tripped circuit breakers. Three 600 VAC inputs, three 4-20 mA outputs. Inputs and outputs isolated from one another. Frequency: 50/60Hz. Maximum primary current: 600 volts. Accuracy: ±0.25% F.S. @60Hz. Output: 4-20 mA. "Zero" adjustment for accurate 0 VAC reading, and "Calibration" adjustment for frequency and voltage level. Powered by the ENVIROMUX-S420MA-24V. Regulatory approvals: UL, CUL, CE. Requires two ENVIROMUX-S420MA-24V to monitor three phases. Caution: installation should be performed by qualified electricians only. Make sure electrical service is disconnected before making any electrical connections.
-
Product
Current Probes
-
Tektronix current probe solutions offer:*The broadest range of AC/DC and AC-only current probes*Measurement accuracy from uAs to 2000 A*Best-in-class bandwidth up to 120 MHz*Best-in-class current clamp sensitivity down to 1 mA*The only products with 3rd Party Safety Certification (UL, CSA, ETL)*The only products with bare wire voltage ratings*Automatic readout and scaling when used with Tektronix oscilloscopes so you don’t have to convert volts to amps or manually set the scaling
-
Product
Wide Angle Scale Instrument
LS-110 LS-80 Var
-
Standard Electric Works Co., Ltd
● Easy to read long-scale and pointer-indications can easily be read from a distance.● Full Scale Deflection : 250°● Accuracy : Class 1.5● Scale Length : LS-110 : 183mm LS-80 : 140mm● Case and Composition : Acrylic resin cover, plastic with UL body and terminal, Four studs mounting. LS-110 case : plastic body option 1 : plastic body with metal case, no UL option 2 : metal case, no UL exception : W, VAR, PF (3P4W)● Color : White scale plate, black terminal plate, black meter body.● Pointer : Sword-type in black color.● TAUT BAND / Pivot & Jewel for LS-110.
-
Product
Optical Gas Imaging Camera
EyeCGas CO
-
Opgal Optronic Industries Ltd.
EyeCGas CO is a handheld OGI camera for CO gas leak detection. With this camera you can safely and remotely detect and locate carbon monoxide as well as other harmful gases emissions. It is also the only OGI camera that is certified for ATEX zone 2 and UL class I Div II, hazardous environments. The EyeCGas CO allows for routine and on-demand inspections in the steel manufacturing operations and other industries where CO emissions need to be closely monitored. With EyeCGas CO, Opgal helps you detect and repair toxic gas leaks inside the facility, whether in vent stacks or pipes, allowing video and audio recording while maintaining safety. Whether these toxic gases are part of the manufacturing process, or a byproduct of the production line, EyeCGas CO helps increasing safety and protect the environment.
-
Product
Mini Redundant Power Supply; ATX 500W
PS500-HRP
-
*Input Range: 100~ 240VAC Full Range*Output Voltage:**+5V, 25A (1A min)**+3.3V, 25A (1A min)**+12V, 41A (1A min)**-12V, 0.8A**-5Vsb, 3.5A (0.1A min)*MTBF(hours): AT 25°C 100,000h*Safety: UL, TUV, CB, CCC, RFI/EMI Standards, FCC Class B, CISPR22 Class B*Dimensions: 185 x 150 x 86 mm*Compatible with Axiomtek products: AX61492
-
Product
IEC60335 Nail Test Probe
CX-Z12
-
Shenzhen Chuangxin Instruments Co., Ltd.
The Finger Nail Probe is indicated to test IEC 60335 and UL requirements. Used to check the security of parts that snap together. The spring gauge assembled in the handle can be calibrated to the necessary force for using the instrument. This probe is made of stainless steel with appropriated hardened tip and a handle in insulating material. Handle has a special adaptor M5 for use with 50N force gauges.
-
Product
Explosion-Protected DIN-Rail Gateway With Intel® Atom® E3940, C1D2, ATEX/IECEx Certification
UNO-410
-
Explosion protection with UL listed Class 1, Division 2 /ATEX Zone 2/ IECEx Zone 2 certificationPort isolation for 8 x DI, 8 x DO, 2 x COMDual storage with M.2 2242 SATA SSD and 2.5” HDD/SSDOnboard TPM 2.0 provides hardware-based securitySupports M.2 3042/3052 moduleMicrosoft Azure IoT Edge and Amazon AWS IoT Greengrass certified
-
Product
Audio Frequency System
Locator Set / UL 30
-
Cable fault location with the BAUR Locator Set / UL 30. The audio frequency system Locator Set is used to exactly determine the alignment of cables and metal gas or water pipes. With various accessories, this system becomes a universal, indispensable device for power companies, industries, installation companies and water suppliers.* Output energy up to 50 VA* Automatic or manual impedance adjustment* Charging unit and rechargeable battery integrated; battery or mains operation* Continuous or cyclical output
-
Product
Analog Oscilloscope
PS-350
-
*40MHz DUAL TRACE, DUAL TRIGGER.*VERT SENSITIVITY FROM 1mV/DIV TO 15V/DIV.*SWEEP RATE FROM 10nS/DIV TO 2S/DIV.*HOLD-OFF, X-Y OPERATION.*CE, TUV GS, UL, CUL, IEC1010.
-
Product
3.0mm Preset Controls Probe
CX-A3C
-
Shenzhen Chuangxin Instruments Co., Ltd.
Used to verify protection against access to hazardous parts by use of a tool through holes which give access to pre-set controls. Meets IEC, EN, UL and CSA Standards including IEC 1010, EN 61010-1, U- 3101-1, UL 3111-1 and CSA 1010-1. The handle and stop face are made of Delrin®. The rod is stainless steel.
-
Product
UL Standards Testing and Certification
-
If you are selling your product in the United States, your product must comply with the applicable nationally accepted UL standards. F2 Labs can evaluate and test your product, help you through the UL certification process and enable you to certify your product to the UL requirements through a Nationally Recognized Test Lab (NRTL).
-
Product
Listed Circuit Breakers
-
Mitsubishi Electric Automation, Inc
To meet the demands of the U.S. and Canadian markets, the UL listed MCCB and ELCB products are compliant to UL489 and CSA C22.2 No.5-02 This range of breakers series offers a standard and high performance protection up to 630 amps and are easily installed in the field accesories.
-
Product
Weather-Ometer
Ci5000
-
Atlas Material Testing Solutions
The Ci5000 is approved by many OEMs in the automotive, paints & coatings and plastics industries as the exclusive platform to deliver accurate, reproducible and repeatable results for predicting service life. The Ci5000 has been certified CE, UL, CSA, ISO and EN compliant.
-
Product
Analog Oscilloscope
PS-200
-
*20MHz Dual Trace, Dual Trigger*Vert, Sensitivity From 1mv/DIV to 15V/DIV*Sweep Rate From 10ns/DIV to 2s/DIV*Hold-off, X-Y operation*CE, UL, CUL, TUV GS, IEC 1010, EN61010
-
Product
PCB Manufacturing
-
SO-9001 and UL certifiedClass IIIRigid circuit boards up to 40 layers3-mil traces and 3.5 mil spacesMinimum Mechanical drill size 8-milMinimum Laser drill size 3-milBlind / Buried ViasControlled ImpedanceRoHS Compliant (all options available)High temperature, high frequency materialAluminum and other exotic material
