Coaxial Switching
Route RF offering excellent signal repeatability and isolation.
-
product
Switching Power Supplies
PeakTech Prüf- und Messtechnik GmbH
A type of power supply that works by switching current into a high-frequency transformer or inductor at frequencies much higher than the input or line frequency
-
product
Test Switches and Accessories
Test switches are designed and manufactured to allow quick and easy multi-circuit testing of switchboard relays, meters and instruments by any conventional system.These test switches and related test plugs have the features necessary for applications involving the measurement of individual currents and voltages associated with substation instrumentation and protection devices. They have been especially designed for the measurement of potential elements, current elements, and make-before-break short-circuit elements related to Current Transformer (CT) circuits.
-
product
Manual Switch Boxes
RTI's manual switch box is a portable and versatile test solution for quick IC electrical verification tests. RTI's 96-pin manual switch boxes integrate with a variety of test configurations that are customized to your test and device needs. It requires no software and connects directly to an external power supply for bias test, and performs quick comparison tests using an A/B relay box.
-
product
10-32 Coaxial Male to 10-32 Coaxial Male, 50 Ohm, 10 ft. cable
786659-01
10-32 Male to 1-Pin 10-32 Male, 50 Ohm Coaxial Cable - The 1032CoaxialM-1032CoaxialM Cable connects data acquisition (DAQ) and control devices such as C Series I/O modules.
-
product
SCSI Switches
Paralan's line of high-quality SCSI switches enable users to switch one host between two strings of peripherals or to share SCSI peripherals between two hosts.
-
product
Public Switch Telephone Network Tester
295B
The Testphone 295B is a test telephone designed for use on Public Switched Telephone Networks (PSTN). It is designed for use on both Dual-tone Multi-frequency (DTMF - tone dialling) and Loop Disconnect (LD - pulse dialling) lines. Fitted with an integral ADSL filter, the telephone will not cause interference when connected to ADSL/Broadband lines in either `on hook` or `off hook` mode.
-
product
PXI Hex SPDT RF Switch SMB 75 Ohm
40-830-006
The 40-830-006 is a 75Ω RF Switch 6 separate SPDT relays in a single PXI slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
product
Emergency Stop Switch [Pushbutton Type]
SG-E1
Panasonic Industrial Devices Sales Company of America
Emergency Stop - Push-Button Type Switch.
-
product
PXI 75 x SPST Ruthenium Reed Relay Switching
40-140A-121
This range of high density reed relay switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose reed relays are suitable for the construction of small switching networks, for slaving up to larger switches or for operating external devices (e.g. lamps, solenoids etc.).
-
product
PXIe-2525, 64‐Channel, 2 A, Multibank, 2‐Wire PXI Multiplexer Switch Module
780587-25
64‐Channel, 2 A, Multibank, 2‐Wire PXI Multiplexer Switch Module —The PXIe‑2525 is a high‐density PXI multiplexer switch module that is ideal for routing signals within automated test systems. It uses electromechanical relays to perform immediate switch operations in one of the following 2‑wire multiplexer configurations: 16 bank 4x1, octal 8x1, quad 16x1, dual 32x1, and 64x1. The PXIe‑2525 also features onboard relay counting for relay monitoring.
-
product
Universal Switch
34980A
34980A Universal Switch Module 34937A, 34938A can be used to send signals or control other devices in the application. The 34937A is a versatile universal switch with 28 channels capable of switching up to 1A. In addition, there are four can switch up to 5A of the A-channel. The 34938A has 20 5A channels of type A topology. Each type A general-purpose switch can withstand up to 150W of power per channel, suitable for power switching.
-
product
PXI Switches
The PXI general purpose switch modules deliver fast, reliable switching in a variety of configurations. Cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids with independent, single-pole, double-throw (Form C) or single-pole, single-throw (Form A) switches in a single PXI module. Choose between the high-speed, long-life reed relays capable of switching up to 100Vrms with up to 1A and 25W of power, or the higher power armature relays capable of switching up to 250Vrms, with up to 2A and 60W of power. The general purpose line also includes a module that offers the performance you need to switch heavy loads with up to 300W (DC resistive load)/1250W (AC resistive load).
-
product
Reference Detect Switch
RDS Series 1.5” x 1.5” x 0.6”
*Connectorized Package *Internal/External Reference Detect Switch *Standard Internal TCXO (±2.5 ppm) *Optional Internal OCXO (±90 ppb)
-
product
PXI 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
40-205-008
The 40-205-008 (PXI) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
product
Coaxial Termination, DC to 2 GHz
909C
The Keysight 909C is a precision, low-reflection dc to 2 GHz load for terminating a 50-ohm coaxial system in its characteristic impedance. It is intended for use as a calibration standard. The Keysight 909C may be ordered with an APC-7, type-N male, or type-N female connector.
-
-
product
Multiplexer C-Size Switching
Explore our array of multiplexer switch cards, each with a unique function for your application.
-
product
Explosion Proof Differential Pressure Switch
1950
Model 1950 Explosion-proof Differential Pressure Switch combines the best features of the popular Dwyer Series 1900 Pressure Switch with an integral explosion-proof and weatherproof housing, making it an exceptional value for either application. It is CE, UL and CSA listed
-
product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
42-203-001
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
product
LXI Remote AC Power Management Switch
60-200-001
If you have ever read the term “programmable except for the supply on/off switch” the 60-200 can provide this capability in a system with the added benefit of an easy to use LXI interface. The 60-200 is a power management switch that provides a means of remotely controlling the power status of up to 8 instruments.
-
product
MICROWAVE SWITCHING DIODES FROM 1 to 40 GHz
Insight Product Company offers Microwave Switching Diodes with switching time up to 3 nsec and operating in frequency range from 1 to 40 GHz. The p+ -n - n+ silicon spackage-less switching diodes are designed to be used in microwave switching devices, phase changers, modulators, microwave attenuators - parts of hybrid microcircuits that provide capsulation and protection against ambient action.
-
product
9' panel mountable, hardened Managed Ethernet Switch
ML1200
The MultiLink ML1200 is a 9' panel mountable, hardened Managed Ethernet Switch designed specifically for use in Industrial Facilities, Substations and Transportation environments. It will supply you with reliable, high-speed networking of all your mission critical applications and provide flexibility and security with easy to use management functions that are unsurpassed in the industry.
-
product
PXI Pull-Thru Adapter, Wired, Micro Coaxial, 18 MCX Plugs and 2 SMB Plugs
510140119
PXI Pull-Thru Adapter, Wired, Micro Coaxial, 18 MCX Plugs and 2 SMB Plugs
-
product
RF Coaxial Interconnect System VPX Compatible Rectangular Harness Solutions
VITA 67 Rectangular Harness
VITA 67 is a VPX standard for blindmate coax connectors that allows high density, high performance RF connections to be made between a backplane and plug-in modules.
-
product
Group Switching Matrices and Multiplexers (Analog & Digital)
GX Series
Cytec GX Series is used to build Group or Gang switches from 2 to 2000 wires. A variety of different modules can be custom configured to switch virtually any type of signal and can be wired out to any type of connector.Group Multiplexers switch any one of several groups of input signals to a single output group, or a single input group to multiple output groups.
-
product
Multiport Calibrated Measurements With Switch Instruments
S97553B
This application provides a macro which enables full multiport error correction and measurement capabilities using external switch instruments
-
product
PXI-2533 , 256-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-33
256-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2533 is a high-density 4x64 PXI matrix switch module built to serve high‑channel‑count automated test systems. Featuring solid-state relays (SSRs), the PXI‑2533 offers unlimited mechanical lifetime and the ability to route 55 W simultaneously on all channels. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
OEM Differential Pressure Switch
MDS
The Series MDS Pressure Switch is designed with a double diaphragm to protect false actuation due to shock and vibration. This low cost pressure switch has a minimum 20 million cycle life expectancy, and an extremely fast response time, making this an ideal device for OEM orders
-
product
USB Programmable SPDT and SP4T Solid State RF and Microwave Switches
LSW Series
The Lab Brick LSW Series RF and Microwave Switch product family offers reliable, high isolation and low cost solid state switch products in both single pole double throw and single pole four throw configurations. These units require connection to a USB port for control and power. No additional DC supply voltage is required. Lab Brick RF and Microwave Switches are easily controlled and programmed directly from the included GUI and through the external control inputs. Lab Brick Switch API DLL and LabVIEW compatible drivers are also available for custom programming applications.
-
product
Multifunction Switch / Measure Unit, Modules
34980A
The 34980A General Purpose switches can be used to route signals or to control other devices in an application. These switches are ideal for device actuation, switching loads or power supplies. Both switches offer high power channels up to 150W. The general purpose modules also include a relay switch counter to help predict when relays need to be replaced.
