Coaxial Switching
Route RF offering excellent signal repeatability and isolation.
-
product
GPS Signal Splitter 12 Way, SMA Jack, 1 - 2 GHz, 50 Ohm Coaxial
GPS121
INSTOCK Wireless Components, Inc
Wideband Frequency (1000-2000 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)15 VDC & 75 mA Max on DC Block PortsTri Alloy SMA Female (Jack) Low PIM
-
product
64-Channel Form A General Purpose Switch for 34980A
34939A
The Keysight 34939A is a high density general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 64 independent single-pole, single-throw (SPST) relays that can switch 1A and carry 2A. This module can be used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. The relays are 100V, 1A contacts and can handle up to 60W. Standard 78-pin Dsub connectors allow for use with standard cables, screw terminal blocks, or mass interconnect solutions.
-
product
Multiplexer Switch Cards
The Adapt-a-Switch® multiplexer switch cards deliver high performance and high density for your microwave switching applications.
-
product
PXI/PXIe Switched Guard Matrix, 16x4
40-590-101
The 40-590-101 (PXI) and 42-590-101 (PXIe) are modules that provide a switched guard 16x4 matrix solution with up to 1012 Ω channel to channel and channel-to-ground isolation.
-
product
PXI Dual Bus 32-Chan 2A Fault Insert Switch, N/O Through Relays
40-190B-502
The Dual Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel.
-
product
Ethernet Switch
SWE440S
The NETernity™ SWE440S is a fully managed (Layer 2/3) 3U VPX Ethernet switch designed to meet the most demanding requirements for network switching in tactical applications. Building on the strong capability and high performance of the SWE440A 3U VPX networking solution, the SWE440S offers the same winning solution and has been designed to align to the SOSA Technical Standard.
-
product
High Isolation USB Switches
RF gain block amplifier from Pasternack is featured in our extensive in-stock RF amplifier selection. Our connectorized gain block RF amplifier uses SMA connectors. This SMA gain block amplifier has a minimum frequency of 500 MHz, a maximum frequency of 2 GHz and a typical gain of 17 dB.
-
product
Switches
Broad / flexible product line100% Quality TestedChoose from a variety of actuators, termination and mounting stylesRoHS CompliantPDF file Basic Switch Technical InformationBasic Switch Technical InformationPDF file Tactile Switch Technical InformationTactile Switch Technical InformationPDF file Switch Selection Guide - 2014Switch Selection Guide - 2014
-
product
PXI-2556, 2.5 GHz, 75 Ω, Dual 4x1 PXI RF Multiplexer Switch Module
778572-56
2.5 GHz, 75 Ω, Dual 4x1 PXI RF Multiplexer Switch Module—The PXI‑2556 is an RF signal multiplexer switch module. The multi-bank architecture of the NI PXI‑2556 makes it ideal for test systems that require parallel operations such as the stimulus/response testing of video RF devices such as tuners. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
Level Float Switch
2285
The 2285 Level Float Switch is suitable for level switching of various liquids, sewage in shafts, tanks, basins or cisterns. The double-chambered float is made of injection molded tough polypropylene that ensures good waterproof protection.
-
product
Coaxial Waveguide Adapter, APC-7, 8.2 to 12.4 GHz
X281C
The Keysight X281C adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
product
GENASYS High Density Matrix Switch Card, 104 X 8 X 8
GX6188 Series
The GX6188 is a 6U PXI, high density matrix, GENASYS architecture switching card. The card provides the user with the ability to connect and interface resources to multiple UUT connections. The board consists of two matrices - a 104x8 and a 8x8 matrix. The GX6188 can connect to 104 UUT switching points, eight external resources and an eight channel global bus via front panel connectors. Multiple GX6188 cards can be connected using the global bus. Like other GENASYS switch cards, the GX6188 features an integral, 3-dimensional switching architecture which provides the flexibility to connect test system resources to multiple UUT connections as well as supporting an expansion bus connection without sacrificing I/O matrix connections when building multiple switch card configurations.
-
product
Vibrating Level Switch
TF 100 Series
TF-100 Series is a vibrating level switch with TF-L relay output and TF-P transistor output or with TF-T current output.This level switch is designed for reliable indication of clean liquids and light slurries. It is available with Relay, Current, and PNP outputs that can be set to indicate alarm on either high level for spill prevention, or low level for run-dry protection.
-
product
Coaxial Waveguide Adapter, 1.85 mm (f), 50 to 67 GHz
V281A
The Keysight V281A adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
product
10-32 Coaxial Male to BNC Female, 50 Ohm, 3 ft. cable
786657-01
10-32 Male to 1-Pin BNC Female, 50 Ohm Coaxial Cable - The 1032CoaxialM-BNC Cable connects data acquisition (DAQ) and control devices such as C Series I/O modules.
-
product
PCI Express Passive Switches
MAX4889
High-Speed PCI Express Passive Switches Enable Gen I Switching
-
product
Chassis - Controls up to 16 Switch Modules in 16x8, 32x4, or Dual 16x4 Configurations
CXB/128-MF
These Chassis controls up to 16 switch modules in 16x8, 32x4 or dual 16x4 configurations. Available as single pole systems with the outer conductor of the BNC taken to ground, or isolated 2 pole systems switching both center conductor and ground. LEDs on the front panel show switch and power status. Add Switch Modules, Driver Modules and a Control Module to complete the system.
-
product
Inducitive Switch Transient Test Circuit
NSG 5071
The basic philosophy of this test circuit is better reproducibility of actual switching transients. The reproducibility of this test circuit comes not from the output characteristics as in traditional conducted automotive immunity tests, but from a fixed design of the generator using several pre-defined components. Many of these components are defined in the standard as "critical" with no substitutions allowed. These components are used as required in the standard.
-
product
Coaxial Calibration Kits
Designed to provide accurate calibrations of network analyzers in the DC to 18.0 GHz range.
-
product
PXI/PXIe RF Switch, Dual SPDT, Terminated, 8GHz, 50Ω, SMA
40-880B-001
The 40-880B-001 (PXI) and 42-880B-001 (PXIe) are dual SPDT 50Ω RF switches with 8GHz bandwidth. The 40/42-880B range has automatic termination of unused signals and are available as a dual switch in 1 slot, a quad switch in a two slots or hex and octal switches in three slots.
-
product
PXI Fault Insertion Switch, 6-Channel, Two Fault Buses, 30 A, Hardware Interlock
40-191B-012-HI
The 40-191B-012-HI is a PXI fault insertion switch with hardware interlock using solid state switching elements and is capable of carrying 40A on single channel or 30A on all channels at the same time and provides a robust solution to high current fault insertion.
-
product
6U VPX Dual-Plane 40 GbE Switch
ComEth4510e
The ComEth 4510e is a combined Control and Data Plane Switch for demanding 6U OpenVPX Ethernet architectures. The ComEth 4510e is backwad compatible with the previous product generation (ComEth 4510a) and adds 40G capability.
-
product
Coaxial Open, 2.4 mm (m)
85141A
The Keysight 85141A coaxial open is used for establishing measurement planes for known reflection phase and magnitude in 50-ohm coaxial systems. It has a 2.4 mm male connector.
-
product
Compact Pressure Transducers And Switches
Compact Baratron® capacitance manometers are ideal for space constrained applications. Compact pressure transducers provide an analog output proportional to pressure, while compact pressure switches provide a relay output based on pressure.
-
product
L31 Series Heavy Duty Vertical Multi-Station Stainless Steel Liquid Level Switch
L31 Multi-level Switch Stainless Steel
As many as six level control points and up to 72” in overall length. Mount at the top or bottom of a tank. It can be fully customized. Typically found in potable water, hot water, acids, and various solvent applications.
-
product
AL600 Is a Single Pair Ethernet (SPE) Switch Designed for Rugged Industrial Applications
EKF-AL600
The AL600 Single Pair Ethernet Switch, 7 x 100BASE-T1, 1 x 1000BASE-T Automotive Ethernet, Industrial, Ethernet, BroadR-Reach.
-
product
Standard 2.90 (82.20) - 5.40 (153.00) Switch Probe
TSP157-F200-1
Current Rating (Amps): 10Average DC Resistance lower than (mOhm): 20Test Center (mil): 157Test Center (mm): 3.99Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 984Overall Length (mm): 25.00Switch Point (mil): 67Switch Point (mm): 1.70
-
product
Waveguide to Coaxial Adapter
D8-AWC100SK-1239
Waveguide to Coaxial Adapter, Frequency 8200~12500MHz, 50W, Rect. Waveguide FBP100, SMA Female
-
product
PXI Single Bus 74-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-301
The Single Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
PXI-2547, 2.7 GHz, 50 Ω, 8x1 PXI RF Multiplexer Switch Module
778572-47
2.7 GHz, 50 Ω, 8x1 PXI RF Multiplexer Switch Module—The PXI‑2547 is an RF signal multiplexer switch module. The higher channel count of the PXI‑2547 makes it ideal for test systems that require the switching of a large number of RF signals, such as switching several devices under test to a single channel on the RF analyzer. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
