Coaxial Switching
Route RF offering excellent signal repeatability and isolation.
-
product
RF & Microwave PXI Switch Modules
These switching systems are used for design validation, reliability and production test including 5G, SD radios, S parameter testing for RF cables, antennas, radar and semiconductor verification.
-
product
PXIe-2739 , 256-Crosspoint, 16x16, 2-Wire PXI Matrix Switch Module
782835-39
256-Crosspoint, 2-Wire PXI Matrix Switch Module—The PXIe‑2739 is a high‐density 16x16 PXI matrix switch module designed for routing signals within automated test systems and using electromechanical relays to perform immediate switch operations. It also offers features to monitor the health of deployed systems and plan for predictive maintenance, including onboard relay count tracking, a temperature sensor, and functional and resistive relay self-tests available through the NI Switch Health Center.
-
product
PXI 5A Fault Insertion Switch 10-Channel
40-196-001
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
product
VVK AXIe Switch
VVK AXIe MODULE
Based on the VVK AXIe module, up to 1500 channels of the TEST-9110-AXIe cable tester can be placed in a 6-slot AXIe crate, 3900 channels can be easily placed in a 14-slot crate, which in terms of channel density is a record among analogues on the Russian market.
-
product
Coaxial Attenuators Set
11582A
The Keysight 11582A contains a set of four 8491B attenuators 3, 6, 10, and 20 dB furnished in a handsome walnut accessory case. The Keysight 8491B are type-N connectors with a maximum frequency of 18 GHz. This set is ideal for calibration labs or where precise knowledge of attenuation and SWR is desired.
-
product
Membrane Switch Tester
Membrane tester used for testing all of your membrane switches, LEDs, keypad, keyboard and switch panel testing, designed with accuracy, ease of use, speed and quality in mind.
-
product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
40-203-001
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
product
AC Control Time Switch
IM1756
Ajinkya Electronic Systems offers AC and water cooler controller, an energy saving device for controller air conditioner unit and water cooler optimally to save Electricity. AC Control Time Switch offers unparallel features to not only save energy but to save compressor from electrical voltage and overload.
-
product
PXI/PXIe RF Switch, Triple SPDT, 3GHz, 50Ω, MCX
40-870A-103
The 40-870A-103 (PXI) and 42-870A-103 (PXIe) are 50Ω RF switches with 3 separate SPDT relays in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40/42-870A has been minimized by careful attention to the mechanical and electrical design.
-
product
PXI 12x4 Matrix, 1 Pole Switching
40-510-021
The 40-510 series of matrix modules feature a wide range of selectable switching configurations (12x4,dual 12x4,12x8 and 24x4). Typical applications include signal routing in ATE and data acquisition systems. Available reed relay formats are 1-pole, 2-pole and 1-Pole screened. The screened version is suitable for switching signals up to 50MHz. Larger matrices may be constructed by Daisy Chaining the common signals from multiple PXI modules.
-
product
Active Switching Rectifiers, 2 KW, P/N 6016C
- Active Switching Rectifier, 2 KW, P/N 6016C- Input Range: 9 VAC to 35 VAC, 3 PH- Frequency Range: DC to 10 kHz- DC output: 13.5 VDC, 70 Amps without any heatsink (Test #1)- DC output: 13.5 VDC, 150 Amps with heatsink (Test #2)- Dimensions: 8″W x 8″L x 3″H or similar- AC to DC and DC to DC applications- Generates less heat as power MOSFET Switching is used- The output voltage is the same as the input voltage
-
product
Diaphragm Operated Dual-Action Pressure Switch
H2
Explosion-proof, UL & CSA Listed for Class I, Groups B, C & D and Class II, Groups E, F & G. The H2 is designed for sequencing two different actions as pressure of a liquid or gas increases or decreases. The patented design consists of two concentric pistons operated by a single diaphragm with one pressure chamber.
-
product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass, Single-Mode
40-860A-122-HI
The 40/42-860A-122-HI is a PXI/PXIe dual insert/bypass switch with FC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
PXI Microwave Switch Modules
Pickering's PXI Microwave Switch Modules vary from simple multiplexer and switch configurations to integrated matrices and large multiplexers. Most products are characterized for 50 operation however certain 75 versions are supplied either as standard or custom products. Remote versions occupy a single PXI slot with the microwave switches mounted separately from the host chassis, connection to the module is via a supplied control cable.
-
product
PXI 8 Channel Switch Simulation Module
40-480-021
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
-
product
Dual Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-002
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
Cable Assembly, Receiver, 20/26GHz Coaxial, 36", 7 SMA Plugs
540133010253
Cable Assembly, Receiver, 20/26GHz Coaxial, 36", 7 SMA Plugs
-
product
64-Ch SPDT 2A-240VAC 24VDC Switching
YAV90164
64 relays SPDT, 2A Switching 2A 250Vac. Up to 62,5VA CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
Static Switches
Static, or solid-state, switches are electronic devices for switching and driving resistors that provide a longer service life than electromechanical relays. Static switches are used to control high-power motors, transformers, tungsten lamps, heating elements and in many of the difficult and heavy-duty applications typical of industries using electric ovens, in the glass and plastics industries.
-
product
RF Switching PXI Card
GX6062
The GX6062 is a high-density 6U PXI RF switching card that provides 200MHz bandwidth and multiple switching configurations. The GX6062 has 12 groups of 1 x 4 differential, non-terminated RF multiplexers. The 12 groups can be used to create multiple configurations including: 6 x 1:9, 3 x 1:19, 2 x 1:29, 1 x 1:59, and more. The GX6062 switching card plugs directly into any 6U PXI chassis.
-
product
High 2.90 (82.20) - 12.60 (357.00) Switch Probe
TSP100-FK180-3
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass
40-860A-322
The 40/42-860A-322 is a PXI/PXIe dual insert/bypass switch with MU connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
PXI-2585, 10‐Channel, 12 A, 1-Wire PXI Multiplexer Switch Module
778572-85
10‐Channel, 12 A, 1-Wire PXI Multiplexer Switch Module —The PXI‑2585 is a high‐power PXI multiplexer switch module that is ideal for switching power signals and loads in control applications and battery, power supply, and automotive testing. It is configured as a 10x1 multiplexer with both low contact resistance and high isolation voltage. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
PXI Single Bus 32-Ch 2A Fault Insertion Switch
40-190B-201
The Single Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
Fullband Coaxial Noise Sources
Our line of full-band noise sources are specially designed for easy integration into microwave systems. They feature rugged construction with excellent long-term stability. In addition to the RF output choices, there are also different packages available to meet a wide range of mechanical constraints. Typical applications include jamming, radar alignment, SNR testing and general lab use.
-
product
Bourdon Tube Operated Pressure Switch
DA/DS
Customers tell us that this is the best pressure switch made. The Mercoid D Series is one of the world's broadest lines of pressure switches. Whatever your application might be, it is most probable it can be fully satisfied with a D Series pressure switch
-
product
GPIB (IEEE-488) Switching
Pickering's GPIB (IEEE-488) switching systems offer you a comprehensive line of switching modules that are ideal for functional test, factory automation and data acquisition applications. These GPIB switching systems range from small low-cost entry level systems to large high performance units with extensive built in self-test.
-
product
Switch Probes
A switch probe is designed primarily for “presence/ electrical” test applications such as detecting the absence or presence of contacts within a wire harness connector. In this case, the switch probe provides electrical interconnection and verifies the connector has been manufactured properly. If contacts are missing or out of place, the part is rejected. If all the contacts are in place, the part is accepted and an electrical test is performed, verifying the electrical integrity of the connector and the wires within the harness.
-
product
Vacuum Switch Tester
Weshine Electric Manufacturing Co., Ltd
1. The instrument has an automatic measurement function.2. The instrument has a perfect back-EMF protection function.3. The instrument uses a 5-inch 65K color LCD touch screen, which is easy to operate.
-
product
Power Switches
SMX-2002 (Power)
The SMX-2002 is the only switch module in its class with the ability to switch up to 16A. Some applications include: AC line power switching, switching of DC or AC power supplies, control or driving relays for industrial machines (robotics, numerical control machines), automotive engine control, and solenoid switching. Since this module typically switches power to the UUT or interface, the SMX-2002 includes failsafe pins on the front panel which can be configured to open all relays when a failsafe signal is activated. This approach can instantly removes all power to the UUT or interface.
