Power Transducers
-
Product
Displacement Transducers
-
Procter & Chester Measurements Ltd
Pressure: Measures gas or liquid pressure. Pressure is an expression of the force required to stop a fluid from expanding. The transducer generates a signal from the pressure imposed upon it.Torque: Measures the torque (or twisting motion) on a static or rotating system. The static torque element has little movement and therefore more economic to manufacture and purchase. Rotary or dynamic torque is more complicated as the signal needs to be transferred using slip rings, wireless telemetry or rotary transformers/inductance technology so that the strain gauged shaft can continuously rotate.Displacement: Measures distance. The displacement transducers that PCM offer are slightly different to standard units. They have a strain gauge/wheatstone bridge. The benefit here is that if the customer has existing electronics that uses strain gauge/load cell technology, they can use them with these sensors.
-
Product
AC/ DC mA Current Clamp-on Transducer
CA-60
-
This miniature clamp meter features two Hall effect sensors. For use with any multimeter with 200mV or/and 2V ranges for direct readout input impedance of least 1M ohm. High conversion factor for low DC and AC mA measurement. With the small jaw size it can fit into tight space in circuit panel or wire bundle to take the reading.
-
Product
Data Loggers, Data Recorders, and Measuring Transducers
-
Wuntronic Data Loggers, Data Recorders, and Measuring Transducers
-
Product
Differential Sensor, Wide Dynamic Range, 100 MHz
CX1105A
Power Sensor
The CX1105A ultra-low noise differential sensor is a dedicated accessory for the CX3300 series and enables dynamic current measurements from 1 μA to 100 A under up to 100 MHz bandwidth with existing shunt resistors on your test board.
-
Product
Germanium Optical Power Head
81623C
Optical Power Sensor
The new 81623C optical power head provides a 5 mm detector area and allows flexible placement of the remote optical power meter, which is then connected to the N7749C. The 81623C accepts parallel beams with up to 4 mm diameter, standard SM fiber and MM fiber with max. 100 μm core diameter, NA ≤ 0.3. A wide choice of adapters allows input from popular fiber connector types, bare fibers or open beams. The magnetic D-shaped adapters allow rapid removal and replacement without twisting attached fibers.
-
Product
Programmable Linear DC Power Supply, 1 Output, 0-16V/0-8A
T3PS16081P
DC Power Supply
Programmable Linear DC Power Supply, 1 Output, 0-16V/0-8A.
-
Product
Compact Pressure Transducers And Switches
-
Compact Baratron® capacitance manometers are ideal for space constrained applications. Compact pressure transducers provide an analog output proportional to pressure, while compact pressure switches provide a relay output based on pressure.
-
Product
3-Axis AC Magnetic Transducer
3DACMT-1
-
The *SENIS* 3DACMT-1 is a cutting-edge 3-Axis AC Magnetic Transducer designed for precise measurement of alternating magnetic fields. It operates within a frequency range of 10kHz to 200kHz, making it an ideal choice for applications requiring high sensitivity and precision. The device features a compact sensing cube with a volume of about 3.6 cm³, ensuring non-invasive measurements that do not disturb the magnetic fields being observed. With its exceptional resolution of better than 1.5μTrms, the 3DACMT-1 delivers a highly linear response and transduction accuracy of ±1%, ensuring reliability even in the most demanding environments. Further, the *SENIS* 3DACMT-1's design incorporates three mutually orthogonal coils, allowing it to capture all three components of magnetic fields simultaneously while being insensitive to electrical fields or capacitive coupling. The sensor's excellent angular accuracy of <±1° and phase accuracy of <3° at 85kHz enhances its capability to provide accurate data. Additionally, with an output signal from 0V to ±5V, and a measurement bandwidth of 10kHz to 200kHz, this transducer is built to handle complex measurement tasks efficiently.
-
Product
Pressure Cell Transducer
-
Unitech Scales And Measurements Pvt. Ltd
*UNITECH’S Pressure Transducers manufactures a wide range of absolute and true gauge pressure transducers.*UNITECH’S Pressure Transducer is mainly a strain gauge based sensors ranging form Vacuum to 1200 Kg/cm2. *The stainless steel construction permits the transducers to operate in rugged, industrial environments. *We also undertake custom-built pressure transducer for specificrequirement and for OEM users.
-
Product
Vacuum Pressure Transducers
-
MKS modular vacuum transducers feature compact size that dramatically reduces installation costs. These vacuum/pressure gauges are ideal for applications where controller size and local control are critically important. They are available as pressure transducers with an analog output, or as vacuum modules with digital communications used to transmit the pressure signal.
-
Product
Autoranging System DC Power Supply, 80 V, 510 A, 15000 W, 208 VAC
N8931A
DC Power Supply
The Keysight N8900 Series provides 5 kW, 10 kW, and 15 kW autoranging, single-output programmable DC power for ATE applications that require just the right amount of performance at just the right price. The N8900 Series power supplies' autoranging output characteristic enables unprecedented flexibility by offering a wide range of voltage and current combinations at full power. Power supplies with "rectangular," or traditional, output characteristics provide full power at only one voltage and current combination. Just one N8900 does the job of multiple power supplies. It's like having many power supplies in one!
-
Product
Regenerative Power System 1000 V, ±90 A, 30 KW, 400/480 VAC
RP7982A
DC Power Supply
The RP7982A regenerative power system is a single output, bi-directional, regenerative DC power supply with safety features to protect your people and your DUT.
-
Product
Regenerative Power System, 160 V, ±125 A, 10 KW, 400/480 VAC
RP7946A
DC Power Supply
The Keysight RP7946A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test.
-
Product
Industrial Mini-Redundant AC Power Supply, 460W
APS-946XAR-EPS12
Redundant Power Supply
- Power (typical): 460W- Current Type: EPS12- AC Voltage Input Range: 110 - 220 VAC (±10%)- Dimensions: 185 x 150 x 86 (mm)
-
Product
Calibrator for Vibration Transducers
HD2060
-
Hand-held calibrator for vibration chains with frequency 15.915 Hz and levels 1 m/s² and 0.1 g, and frequency 159.155 Hz and levels 10 m/s² and 1 g. With LCD display.
-
Product
AC Current Transducer
iDVM 333
-
The iDVM 333 AC Current Transducer plugs into the iDVM 510 multimeter and measures current (as AC millivolts) with no need to break the circuit. Special Introductory Price: $52.50FeaturesTransformer jaws that detect AC current flowing through a conductorSelectable sensitivity between 1mV/A and 10mV/AHand Guard to protect your hand for safetyLarge, easy-to-operate trigger opens the transformer jaws
-
Product
Programmable Linear DC Power Supply, 4 Output, 0-32V/0-3A, 0-5V/0-1A, 0-15V/0-1A
DC Power Supply
Programmable Linear DC Power Supply, 4 Output, 0-32V/0-3A, 0-5V/0-1A, 0-15V/0-1A.
-
Product
Test and Measurement Grade Vacuum Pressure Transducer
P897V
-
The P897V is designed for a wide variety of pressure measurements where high resistance to vibration and superior stability through temperature change is required. The zero and full-scale output calibrations are set by the potentiometer adjustments accessible from the top cover. The P897V is digitally compensated and corrected to provide high accuracy pressure measurement in a robust cylindrical form factor. Small vacuum pressures are accurately measured with full scale vacuum ranges as low as 2.22 InH2O.
-
Product
Acquisition Of 16 Displacement Transducers
APCI-3701-16
-
PCI interface to the 32-bit data bus Acquisition of 16 inductive displacement transducers (Half Bridge, LVDT) 16 input channels ± 10 V 16-bit resolution Measuring frequency up to 100 kHz Conversion can be triggered through software End of conversion can be inquired through software Possibility of interrupt through digital input channels (when a data or a time value is exceeded) PCI-DMA access Onboard FIFO buffers Sequence RAM 16 isolated digital I/O, 24 V Software operation Supported inductive transducers for APCI-3701Standard board APCI-3701-8 or APCI-3701-16Transducer type:
-
Product
DC/10 MHz – 18 GHz USB Thermocouple Power Sensor
U8481A
Power Sensor
The U8480 series is the fastest USB thermocouple sensor in the world without compromising the best in class linearity of the legacy 8480/N8480 series thermocouple sensors, all in a compact USB based form factor
-
Product
Combined Pressure and Temperature Transducers
-
Variohm offer some different styles of combined pressure and temperature transducers including the EPTT5100 which has an internal temperature sensor and the miniature EPTTE1400 which has an external temperature probe.
-
Product
cPCI System Power Supply
VX6620
Programmable Power Supply
The potential-free power supplies of the VX66xx family stand for precision and reliability and are characterized by many extras such as extremely low noise, very short rise and fall times and additional measurement functions. The energy is completely provided by the PXI chassis, therefore external power supplies are not necessary
-
Product
Power Supplies
ZPG-600B
-
80Plus Gold Certified provides typical 87% efficiency at 50% of max load. The ZPG series can give you the power you need at higher efficiency, which means you can use the same power with less energy. Built in QUAD 8-pin PCI-Express graphic card connector offering further upgradability.
-
Product
Power Supply
-
Our extensive power supply selection features AC and DC power supplies, as well as uninterruptible products. You should have confidence in your power supply, whether you use it during device testing and measurement, product development, production, or maintenance.
-
Product
Power Supply
-
The Power Supply Systems are the heart of any experiment. They provide the High voltage and Low voltage required by the detectors and by the related front-end electronics. The quality of the power supply is critical to obtain the best performance from the set-up. The sensibility of modern detectors, in fact, make them susceptible to any even small variation in the power supply, and so features like low Noise, low Ripple and high stability become essential in the design of a performing power supply system. Strong of 40 years of collaboration with the most important research labs worldwide CAEN offers today sophisticated High Voltage Power Supply and Low Voltage Power Supply Systems. The demonstration of this successful long-standing tradition is the “CMS Crystal Award 2009” that CAEN received for the development and production of the power system for the CMS tracker. CAEN offers a wide selection of Power Supplies in different form factors and standards:- For smaller set-ups Standalone or modular (NIM / VME) products or are the ideal fit.- For bigger set-ups, where a high number of High voltages and Low voltages is required, the Mainframe Systems and Boards (up to 48 channels/board, up to 768 channels in a single Mainframe) are the most recommended.
-
Product
Power Supply
-
Constantly calculates and adjusts the Voltage and Current limit points according to availablemaximum power (160W)At maximum current (10A), voltage is limited to 16V;at maximum voltage (42V), current is limited to 3.8ADual action rotary encoder control with push knob for fine and coarse tuning Remote control for Programming, Output Voltage/Current, and ON/OFF using supplied software, driver,and USBStore 20 presets with up to 999 cycles each on a PCvia USB and supplied SoftwareOutput Voltage: 0 to 42VOutput Current: 0 to 10ABasic Accuracy: (0.2%+5 counts)
-
Product
500 Watt AC/DC Power Line Conditioner, 3U VPX, Holdup Time
VPX56-3HU
Power Line Conditioner
NAI's VPX56-3HU is a rugged, high-performance 500-Watt Output +28 VDC Input 3U VPX AC/DC Power Line Conditioner designed for aerospace, defense, and industrial markets. This off-the-shelf power supply plugs directly into a standard VPX conduction cooled chassis and protects downstream DC-DC converters from MIL-STD-704 transients, low-voltage conditions and power interruptions, providing up to 50 milliseconds of holdup time at up to 500-Watts. Continuous Background Built-In-Test (BIT) and I2C communication are included.
-
Product
High Power DC Power Supply
-
*Low ripple and low noise*High resolution and accuracy (0.1mV/0.01mA)*Built-in high-accuracy 5 1/2 voltmeter and milliohmmeter*Supporting high-accuracy and dynamic programming output*High-luminance VFD screen with two lines& four channels display*Intellegent fan system fan will be automatically initiated according to the temperature*Supporting remote voltage compensation and multidata storage*Supporting external trigger input and output*Power-on-self-test, software calibration and standard rack mount*Using standard SCPI protocol*Communication mode: RS232/RS485/USB.
-
Product
Digital Display for the Transducers and Transmitters
PS57
-
The PS57 is a combination power supply and 4 1/2 digit LED display for the P55/P855 family of pressure transducers and transmitters. The PS57 accepts 110 VAC power and provides the required 24 Vdc excitation for the transducer. The transducer signal is received and displayed directly in engineering units with bright 0.56 high red LEDs. The user can re-scale the display and set the decimal point by configuring internal jumpers. The analog output of the transducer, 5 Vdc or 4-20 mA, is available on rear-panel terminals.
-
Product
Power Regulators
MCE ADV
-
Lifasa - International Capacitors, SA
The energy regulators of the MCE ADV series are designed to measure the reactive power needs of an installation and to give the corresponding capacitor connection and disconnection orders to maintain the cosine φ preset.
