Power Test Systems
-
Product
Medalist i1000D
U9401B
In-Circuit Test System
The Keysight Medalist i1000D is now even better. Improving from its previous state of an analog-only ICT, the new digital release of the system now features per pin programmable digital cards and a whole new set of intuitive software graphical user interfaces (GUIs) that makes programming and development effortless.
-
Product
DC System Power Supply, 20 V, 38 A, 760 W
N5744A
Power Supply
The single output, 760W N5744A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current.
-
Product
Power, Patchcord, ITA, Micro Power, 36", 14 AWG White XLPVC, Single Ended, (22 Amps)
7-251954000-036
Power Patchcord
Power, Patchcord, ITA, Micro Power, 36", 14 AWG White XLPVC, Single Ended, (22 Amps).
-
Product
Optimize Throughput And Cost For MmWave 5G Device Functional Test
Functional Test
Test engineers always have faced tough new test-coverage challenges. Those introduced by 5G measurements at mmWave are no exception, as they require over-the-air (OTA) radiated test solutions. But never have these pressures seen today’s intense time-to-market, manufacturing volume, and operational expectations! A solution that meets these demands must:
-
Product
Power Supplies And Loads
Power Supply
Power Supplies and Loads power devices under test (DUTs) such as RF power amplifiers and cellular handsets. The power supply takes in AC power and delivers DC voltage with a fixed polarity, either positive or negative, to its load.
-
Product
IFC Antennas & Radome Systems
System
System solutions providing inflight internet and live TV connectivity including satellite communications (SATCOM) systems, protective radome enclosures, antenna mounts, bird strike solutions, and adapter plates.
-
Product
60W Dual Output Power Supply Two 35V, .8A or 60V, 0.5A
E3647A
Power Supply
Keysight basic DC power supplies offer essential features for a tight budget. The single & dual output, 30-100 W GPIB E3640 series provide small, compact size for bench and system use; low output ripple and noise; and built-in measurements and basic programmable features with GPIB and RS232 interface. The Keysight 58W, multiple output E3647A is a clean, reliable power supply for general purpose applications, and combine convenient benchtop capabilities with flexible system features in a compact, multi-output package.
-
Product
Mezzanine System
3564
System
The 3564 is a four channel comparator board with a common mode range of -150V to 150V on the two differential inputs and a DAC per channel to set trigger levels. The high common mode range and DC coupling provides a robust solution to level detection and triggering.
-
Product
Power, Patchcord, Receiver, 36", High Power, 2 AWG, to Ring Terminal (150 Amps)
7-221902688-036
Power Patchcord
Power, Patchcord, Receiver, 36", High Power, 2 AWG, to Ring Terminal (150 Amps).
-
Product
Power, Patchcord, ITA, 36", High Power, 2 AWG, Single Ended (150 Amps)
7-222902000-036
Power Patchcord
Power, Patchcord, ITA, 36", High Power, 2 AWG, Single Ended (150 Amps).
-
Product
10 MHz To 67 GHz LAN Thermal Vacuum Compliance Power Sensor
L2067XT
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
Product
Power Monitor, AC- or DC-Powered
109
Power Monitor
NAI’s 109 is an AC- or DC-Powered Power Monitor used to monitor voltage, frequency, and phase characteristics of single- or three- phase power lines. This allows normal operation of system loads when the power-line characteristics are within predetermined limits.The 109 monitor provides three separate control circuits and output relays indicating the condition of each line characteristic. It is ideally suited for rugged defense and industrial applications.
-
Product
10 MHz to 40 GHz LAN Wide Dynamic Range Average Power Sensor
L2054XA
Power Sensor
The Keysight L2054XA is a fast, accurate and wide dynamic range 10 MHz – 40 GHz LAN average power sensor.
-
Product
Dynamic Test Systems
H3TRB | HTGB (HTGS) | RTGB (RTGS)
Test System
Durability and reliability of wide-bandgap materials such as SiC and GaN are an important topic. The focus here is on new failure mechanisms whose effects are not visible with traditional H(3)TRB/HTGS – but which nevertheless have an influence on the real application.
-
Product
DC/10 MHz 67 GHz USB Thermocouple Power Sensor
U8488A
Power Sensor
The U8480 series is Keysight's first power sensor with the capability to measure down to DC (only applicable for U8481A/85A). Now, with an expanded frequency range up to 50 and 67 GHz, the U8480 series allows you to make fast and accurate high frequency power measurements in applications ranging from PNA/MXG calibration to high volume manufacturing.
-
Product
Flexible Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131E
test
Achieve phase stability with this 96.5-cm cable when a DUT is connected, with adapter, directly to the test set port
-
Product
10 MHz to 50/53 GHz LAN Wide Dynamic Range Peak and Average Power Sensor
L2065XA
Power Sensor
The Keysight L2065XA is a fast, accurate and wide dynamic range 10 MHz – 50/53 GHz LAN peak and average power sensor.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196B
Test Fixture
The 16196B surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results, reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement. Now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Regenerative Battery Pack Test System
17040E
Test System
High-power testing equipment up to 1,700V/ 4800A/ 1.2MW Multiple safety protections for personnel safety risk management and control of battery testing Flexible Integration for automated battery verification solutions
-
Product
10 MHz to 33 GHz LAN Wide Dynamic Range Average Power Sensor
L2053XA
Power Sensor
The Keysight L2053XA is a fast, accurate and wide dynamic range 10 MHz – 33 GHz LAN average power sensor.
-
Product
Low Side, 200 MHz, 100 PA – 20 MA
CX1103A
Power Sensor
The CX1103A low side current sensor is a dedicated accessory for the CX3300 series mainframe and features the series widest stand-alone bandwidth up to 200 MHz
-
Product
Fixture Kit 600x455mm RCV 8-slot for 6TL34
AG588
Test Fixture
Stopper kit includedYAVCANCON2 for fixture identification not included
-
Product
EMI Test System
TS9975
Test System
The R&S®TS9975 is the base system for conducted and radiated EMI measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for large equipment under test. Combinations of different applications or incremental expansion are easily possible.
-
Product
Thermocouple Power Sensors
N8482H
Power Sensor
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
DC System Power Supply, 80V, 9.5A, 760W
N5748A
Power Supply
The single output, 760W N5748A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current.
-
Product
Image Sensor Test System
IP750
Test System
Teradyne's IP750 series dominates the image sensor tester market with its superior performance and low cost of test. The IP750 delivers high throughput and high parallel test efficiency, broad device test coverage from CCD and CIS, analog and digital capture, and concurrent image sensor and logic testing. In addition, Teradyne's IG-XL software environment provides easy, shorter test program development and easy maintenance.
-
Product
DC System Power Supply, 12.5 V, 60 A, 750 W
N5743A
Power Supply
The single output, 750W N5743A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current
-
Product
Sealed Beam Bulb Testing System
H710019SSL
Test Platform
EOL test for manufacturing of bulbs with LED for applications requiring to ensure watertightness: vehicles, marine, swimming pools, operating rooms, classified areas (Ex Zone), etc. The test system checks in a short time all the light and electrical characteristics of the bulb. A high precision Micro Leakage Meter also checks that there are no leaks between the environment and the inside of the bulb. The test results are recorded on the PC and can be printed on a quality control label attached to each unit.
-
Product
DC System Power Supply, 600 V, 1.3 A, 780 W
N5752A
Power Supply
The single output, 780 W N5752A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current.
-
Product
128 DIOs JTAG Boundary Scan Resources Unit
YAV9JTAG
Test Fixture
Boundary-scan is a widely practiced test methodology that is reducing costs, speeding development, and improving product quality for electronics manufacturers around the world. By relying on an industry standard, IEEE 1149.1, it is relatively quick, easy, and inexpensive to deploy a highly effective test procedure. In addition, today’s PCBs have little alternative because of limited access to board-level circuitry.
