Test Clips
See Also: Clips, Kelvin Clips, Alligator Clips, DIP Clips, IC Clips, Bed of Nails
-
Product
IP67 Testing
-
IP67 is an electronics and sealed device attribute requirement with a physical no-water ingress testing process used to determine whether components meet the requirements needed to receive an IP (ingress protection) rating. Devices with this internationally recognized rating resist exposure to dust and withstand up to 30 minutes of submersion in water up to 40 inches (1 meter) in depth. Products assigned an IP67 rating are typically used in outdoor applications or other environments requiring resistance to dust, moisture, and water submersion.
-
Product
Transformer Resistance Testing
-
Transformer insulation resistance deterioration is one of the most common causes of transformer failure: a failing transformer is a costly replacement in an electrical system with the potential for a long downtime. If you fail to maintain your transformer with regular insulation resistance testing (as can be carried out by the Megger Transformer Ohmmeter (MTO) series of transformer test equipment) then it’s likely to fail before reaching its maximum operating life.
-
Product
Radio Test Set
CMA180
-
With its frequency range from 100 kHz to 3 GHz, the R&S®CMA180 is ideal for testing all common analog and digital radio systems. Input levels up to 150 W are no problem for the R&S®CMA180. The flexible internal switching capabilities for the audio and RF paths make the R&S®CMA180 suitable for a wide range of test requirements. Users can configure the internal generators, external audio sources, filters and measurements according to the given application. In the predefined test scenarios for receiver, transmitter and duplex tests, the RF and audio paths are preconfigured. This saves time and eliminates configuration errors for standard test cases.
-
Product
Operational Modal Testing
-
EDM Modal Operational Modal Testing (OMA Testing) includes a dedicated test setup and operation process flow using ambient vibration data. Using a large channel count data acquisition system (e.g., Spider- 80X or Spider-80Xi), the excitation method provides a much higher efficiency and accuracy for FRF measurements while minimizing local stresses on the test article.
-
Product
Test & Measurement
-
NIF (Dutch Instrument Factory, later Nieaf-Smitt) started in 1900 as one of the first organizations in the world with the design and production of instruments for electrical values. The portfolio of test tools, digital multimeters, current clamps, device testers, installation testers and power analyzers is characterized by quality and reliability.
-
Product
Meter Test Benches
Test Station
-
The meter test station allows simultaneous testing of 3, 5, 10 or 20 induction or static electricity meters. The test station could be constructed for single-phase electricity meters or for three-phase meters.
-
Product
Test Accessories
-
For in-house designed ATE systemsFor any customer’s existing systemProviding complete electrically- and mechanically-designed units from the customer’s own specificationsUtilize our build-to-print services to duplicate your existing design
-
Product
Environmental Test Equipment
-
Shenzhen Everbest Machinery Industry Co.,Ltd.
Environmental Test Equipment Environmental testing can identify and quantify compounds and pollutants in air, water, or soil.
-
Product
Custom Testing
-
You create a custom test plan (a file that lists a series of tests to be run), to meet requirements specific to your environment and apply that test plan to any number of clusters. You specify the order in which tests run and the specific components to be tested. After you set up your custom test environment, you run the test procedure from SMIT and view test results in SMIT and in the Cluster Test Tool log file. For information about customized testing, see Setting up custom cluster testing.*Fixture Design*Fixture Fabrication*Custom Test Stands*Prototype Testing Services*Product Safety Testing Services
-
Product
Test system software
CITE
-
CITE (Computer Integrated Test Environment) is the software platform for all Digitaltest test systems. It is a real-time system offering a vast number of tools to ensure high test quality and shortening testing time. The software also provides you with several different programming languages that you can choose from.
-
Product
Package Testing
-
Package testing helps manufacturers verify their package designs to ensure that their products will not experience damage during shipping. Products are often shipped across states, countries and continents to reach their destination. This is an unavoidable link in the supply chain and, as such, packaging must be designed to protect products during the shipping process.
-
Product
Ethernet Service Testing
-
Artiza Networks offers compact Ethernet service testing devices for Carrier/Metro Ethernet service providers. The GEST-1K and XEST-1 are fast and lightweight, and don’t require a technician to install.
-
Product
ARINC 818 Tester
Test Platform
iWave 3U VPX High-Speed Video/Data Processing Card is a rugged standalone module in the 3U VPX form factor, aimed for the high-speed data, video processing, and display applications is ideal for military, defense, and aerospace applications requiring an optimal balance of performance and power efficiency. iWave 3U VPX High-Speed Video/Data Processing Card is implemented using Xilinx Kintex-7 device architecture and has I/O interfaces including High speed 16 channels of transceiver interfaces capable of operating up to 6 Gbps data rate, Gigabit Ethernet, RS232, RS422, PCIe interface, Built-in health monitoring circuits, HDMI input, and output interfaces
-
Product
Mechanical Shock Testing
-
Classical • Half-sine • Sawtooth • Shock Synthesis • Sustained Presure Shock Response Spectrum (SRS) • Transient Shock Response
-
Product
FPGA Test System
DO-254/CTS
-
DO-254/CTS™ is a fully customized hardware and software platform that augments target board testing to increase verification coverage by test and satisfy the verification objectives of DO-254/ED-80. The target design runs at-speed in the target device mounted on the custom daughter board. The simulation testbench is used as test vectors to enable requirements-based testing with 100% FPGA pin-level controllability and visibility necessary to implement normal range and abnormal range tests. The FPGA testing results are captured at-speed and displayed using a simulator waveform viewer for advanced analysis and documentation.
-
Product
Multi-Stage Functional Test Systems
-
Circuit Check’s bi-level and multi-stage fixtures combine multiple test levels in a single fixture using controlled actuation and selected probe travels for powered and unpowered tests.
-
Product
Testing Accessories
-
Optellent offers a range of accessories to facilitate fibre optic and wireless components transmitter and receiver testing.
-
Product
Testing of Power Steering Motors
-
Endurance test bench on which up to five drives can be tested at the same time. The drives / DUTs are electrically connected to resistors and driven by a servo drive according to a predefined driving profile. This exam can take up to several days. It detects currents, speeds and temperatures.
-
Product
Measurements & Material Testing
-
MAGNET-PHYSIK Dr. Steingroever GmbH
, we can offer measurement tests and material tests of all kinds on hard and soft magnetic materials. It is also possible to carry out measurements on site. We carry out stray field measurements on your magnetization station in production in accordance with the professional association regulations (BGV). We also carry out magnetic field measurements on air freight goods in accordance with IATA 953.
-
Product
Optical Loss Test Set
KI23424OL-INGAAS-APC
-
A Quad Two-Way Optical Loss Test set / OLTS fiber tester that's perfect for medium to ultra high fiber count loss, length & optical return loss testing applications on both multimode and single mode fiber with APC connectors on both ports at 850 / 1330nm 1310/1550 nm. A pair of these compact SM & MM instruments set new standards of productivity, ultra-stable source accuracy and ease of use.
-
Product
Solar Radiation Testing
-
Solar radiation on materials can cause cosmetic deterioration with the fading or oxidation of plastic. This oxidation can make components start to fade and weaken. The heating effects of the sun can cause plastic, vinyl and/or metal components to shift or distort, causing operational interruption, shorts and false control inputs. The most significant effect is discoloration that cheapens the look of any quality product. These effects can be accentuated when combined with temperature and humidity.
-
Product
Banana Alligator Clips, 1-Red and 1-Blue
PK30X-2
-
Banana Alligator Clips, 1-Red and 1-Blue.
-
Product
Airflow Testing Instruments
-
Kanomax USA is one of the leading manufacturers of airflow testing instruments for HVAC Testing, Cleanroom Monitoring, Industrial Manufacturing, and much more. Our airflow testing instruments include air velocity meters, airflow capture hoods (i.e. balometers), micromanometers, a duct air leakage tester, high temperature anemometers, transducers, transmitters, and multi-channel anemometers.
-
Product
EFI Test Light-GEO TBI
3413
-
Peaceful Thriving Enterprise Co Ltd
*Simply for testing: Disconnect the fuel injectors, plug in a Noid.*Quickly determines if the electrical signal present at the fuel injectors.*Light and crank the engine, a flashing Noid light indicates normal pulsing voltage.
-
Product
Walk-In Altitude Test Chamber
-
WEIBER Altitude Test Chambers combine temperature and altitude to test basic components or subassemblies designed for use in a variety of industries. With altitude test chambers, user can control the temperature environment for testing while simulating various altitudes from site level to 100,000 feet (1.12kPa)High and low Temperature Altitude Test Chamber is used to test temperature and low-pressure altitude conditions simultaneously. All models are factory tested, with an ergonomic and maintenance cum user-friendly design.These CE approved test chambers are created with multi-layered insulation with double vapor barrier is of low 'K' factor, high density and of non-hygroscopic in nature. WEIBER test chamber are made in accordance with the international standard.Standard as well as customizable models are available. Walk in models are also available.
-
Product
Temperature & Humidity Testing
-
DATASYST Engineering & Testing Services, Inc.
DATASYST can simulate both high and low temperature with humidity conditions. Cycle rates are dependent upon individual chamber capabilities and whether or not a unit under test is powered or not. DATASYST provides humidity testing for a range of industry specifications and can work with you on your customized testing requirements.
-
Product
µHELIX® Test Probes
Series S200, S300, S400, and S500
-
Test Probes for fine-pitch applications: CSP, BGA, SiP, SoC, flex-circuits, micro pcb, sub-mm center-to-center spacing, half mm, quarter mm spacing. Excellent for use in sockets, fixtures, and contactors for semiconductor testing and in coaxial installations.
-
Product
Thermal Testing
-
A view of multiple testing stations for use in conducting Thermal Analysis on various materials. This is one of several areas assigned to various thermal tests. Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TGA), Thermomechanical Analysis (TMA), and Dynamic Mechanical Analysis (DMA)
-
Product
Fused Visible & IR Testing
-
SBIR offers a visible/NIR/I-Squared/IR target projector that features a fused visible and thermal source capability by combining a MWIR and LWIR differential blackbody source with a visible/NIR integrating source. A beam-combiner allows the thermal energy and the visible energy to be processed simultaneously on the optical centerline of the collimator.
-
Product
Assembly & Test Services
-
Once piece parts have been manufactured, skilled operators can kit or assemble them to the desired level. Our wiring technicians are trained to IPC standards of workmanship and operate within ESD controlled areas. We carry out both solder and crimp wire terminations along with integration of electronic components such as fans, PCBs and power supplies.
