Response
-
product
Transmitters
Seismic transmitters provide a 4-20mA DC signal output proportional to the vibration amplitude, and are ideal for applications where a PLC, DCS, or other automation system will be used instead of a stand-alone vibration monitor. Metrix offers seismic transmitters with a wide variety operating temperatures, frequency responses, scale factors, case materials, connector types, mounting options, and hazardous area approvals.
-
product
PWM TO VOLTAGE SIGNAL CONVERTER
RCPWM2V
The RCPWM2V is a device that converts a standard hobby RC signal (1-2ms pulse) into a proportional analog voltage (0-5V). In many electronics applications the main processor is constantly busy and does not have the ability to address the time-sensitive PWM signal from an RC receiver immediately. This results in signal distortion or a sluggish response due to the extra filtering required. The RCPWM2V provides a simple solution by converting the signal into an analog signal. The main processor can then read the signal whenever it has time.
-
product
Low Cost Microwave Wideband APD Preamp Receivers
MR11 (40KHz~18GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MR11 series microwave wideband optical receiver, adopts high Sensitivity APD diode and Low Noise Preamplifier IC, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave-guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s high speed communication system.
-
product
2.5 GHz, 0.9 pF, 1 MOhm Active Voltage Probe
ZS2500
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.9 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS2500 is ideal for 2.5 GHz and lower oscilloscopes.
-
product
Gas Detectors/Air quality Testers
Adopts the high quality and high performance catalytic combustion sensor with high sensitivity, good reliability, fast response and high stability. The instrument is widely used in urban gas.Department of petroleum,petrochemical,oil depots and gas stations and oil gas transmission and distribution pipeline safety inspection and pipeline maintenance and leakage and rescue etc.,gas industry essential leak detection equipment.
-
product
Scalable 16-Bit Data Acquisition
DAP 5016a
When your application needs Pentium-powered, real-time processing and 16-bit sampling under Windows, choose the DAP 5016a. Even at maximum sampling rates, the combination of a fast processor with low latency allows computation in real time between samples – and on-time response for control applications.
-
product
GPS Speedometer/GPS Vector Speedometer
LC-8120/LC-8220
The LC-8120/8220 is the GPS-based speedometers which measure speed and distance of moving objects with high accuracy. Support for GLONASS satellite which is not supported in the conventional model (LC-8100A/8200A) to ensure stable measurement. Antenna for LC-8220 (LC-0721) is smaller and lighter than the conventional antenna for LC-8200A (LC-0086) and it enables easy operation. The new antenna (LC-0721) is able to attach to the conventional unit of LC-8200(A) for measurement. The linearity of acceleration and angular speed are improved by using the standard IMU (inertial measurement unit) together with the optional high accuracy IMU. Also, by adding the high response IMU analog output function (option), the analog output frequency of the IMU data can be increased from 100 Hz to 500 Hz. A wide range of optional functions such as white-line detecting function (LC-0856), jerk measurement function (LC-0871) and average deceleration speed calculation (function in the LC-0831) are available for various automotive tests.
-
product
PCI High Density Resistor Card 10-Channel, 12-Bit, 0 To 4k Ohm
50-295A-121-10/12
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Digital Panel Mount Load Cell Meter
MODEL DPM-3
The DPM-3 is a smart Plug & Play TEDS IEEE 1451.4 compliant Digital Panel Mount Load Cell meter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the DPM-3 will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the DPM-3 can be set up by simple front panel push buttons. The DPM-3 can be scaled to a full 5 digit display from 0 to 99,999 counts to read directly in engineering units such as grams, ounces, pounds, etc. The DPM-3 samples 60 readings per second (50 for 50Hz operation) for fast control response and true peak/valley reading capability. The meter has an adaptive digital filter that can automatically select the best time constant for minimum noise, yet respond rapidly to an actual change in signal level. The peak and valley values can be displayed by a push of a button on the front panel. Auto-tare allows the meter to be set to zero for any input signal level. Available options include dual relays, analog output, serial communications, and low voltage power supply.
-
product
Free Space Optical Receivers
These optical receivers have bandwidths in the DC to GHz range for detecting high speed free space optical signals with the lowest noise and cleanest responses possible.
-
product
Antenna, Biconical
EM-6912A | 30 Mhz – 300 MHz
A balun, feedline, and element cage give the Electro-Metrics EM-6912A response curves that are almost linear, making it ideal for swept measurements. An added benefit is that the EM-6912A has an improved BALUN design, which makes it insensitive to changes of orientation while vertically polarized. Readings obtained will be the same no matter which element is closest to the ground plane, eliminating a potential source of measurement error.
-
product
PXI Resistor Module 2-Channel 2R to 32.7k
40-293-032
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
In-Process / In-Line Spectrophotometers
Hunter Associates Laboratory, Inc.
Installed within a process stream, in-process (in-line) spectrophotometers provide continuous color measurement data throughout a production run, enabling quick responses to color variations.
-
product
Mobile Comm DC Source w/ Battery Emulation
66321B
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66321B mobile communications dc source provides fast transient response, exceptional sourcing, output resistance programming, and precision measurement. This product is specially designed for testing next generation digital wireless communications products. The 66321B mobile communications dc source offers a new capability that simulates the internal resistance of a battery or battery pack. Additionally, these high performance models offer improved transient response and stable output operation with either short or long load leads.
-
product
Integration API
Testdroid API is an easy-to-use gateway for managing your development and testing effort on real Android and iOS devices. As an alternative for an official Testdroid Cloud site, the API provides all infrastructure through different clients (e.g. Java, Python, Ruby) following the RESTful architecture paradigm and returning JSON with appropriate HTTP response codes.
-
product
High Speed Response, High Accuracy DC Leakage Current Sensor
DCZCT-20CDHL
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Low DC current measurements.*DC1mA～200mA*High accuracy.*±1%F.S ±10mV*Least influence of magnetization.*Less than DC1mA in current level*Convenient +5V single polarity power supply.*Reference voltage (Vref) terminal is equipped.
-
product
NI-5782, 100 MHz Bandwidth Transceiver Adapter Module for FlexRIO
782705-02
The NI‑5782 is ideal for applications that require the acquisition and generation of IF or baseband signals with in-line, real-time processing. You can analyze acquired signals in the PXI FPGA Module for FlexRIO to perform measurements and generate response signals. Application areas include RF modulation and demodulation, channel emulation, bit error rate testing (BERT), signal intelligence, radio frequency identification (RFID) and near-field communication (NFC) test, real-time spectrum analysis, and software defined radio (SDR).
-
product
ION 100 Portable Ion Meter
The new addition to the Environmental Express Oakton product line features updates to measuring water quality easier and faster. The larger LCD display is 2.75 in. by 2.0 in. for a better viewing angle, and has indicators for battery life, stability, and calibration. The ION 100 meter measures pH, mV, ion concentration of 16 commonly measured ions, and temperature. The microprocessor-based meter features automatic calibration, automatic temperature compensation, function setup, self-diagnostics, automatic power-off, and low voltage display. The meter uses advanced digital processing technology, intelligently improving the response time and accuracy of your measurements. Easily switch units among pX, mol/L, and mg/L (ppm).
-
product
PXIe-4145, 4-Channel, ±6 V, 500 mA Precision PXI Source Measure Unit
782435-01
PXIe, 4-Channel, ±6 V, 500 mA Precision PXI Source Measure Unit - The PXIe-4145 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote (4 wire) sensing for accurate measurements. The fast sample rate of the PXIe-4145 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4145 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
-
product
Electronic Load
* Fully programmable, self-contained, air-cooled solid state load.* Patented design is optimized to provide ultra-low impedance operation for fuel cell testing.* Load is compatible with AC impedance or frequency response analyzers.* Interchangeable shunts for precise operation over a wide dynamic range.* Ten built-in cell voltage monitoring inputs optional. Additional voltage monitoring inputs available.* Ethernet Interface for simple configuration and expansion!* Combine with additional Fideris™ Innovator Series™ modules to create a fully-integrated,fully-automated, customized test system.* System-wide control of all Fideris™ Test System Components using FCPower™ Software,LabviewTM, or other programming language.* Integrated hardwired Run/Standby signal.
-
product
Silicon Based Thermopile Detector: 4 Channels
ST120 Quad
A four-channel silicon-based thermopile in a TO-5 package. Each small active area is 1.2mm x 1.2mm . Time constant of 25ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
product
Battery Analyzers
BA6010 Series
The BA6010 Series battery analyzers measure voltage and resistance of modern battery technologies with high accuracy, resolution, and speed. Additionally, these instruments provide auxiliary measurement parameters inductance, capacitance, dissipation factor, impedance, quality factor, reactance, and phase angle in degrees and radians. The BA6010 Series is suitable for characterizing battery chemistries that are responsive to a 1 kHz AC stimulus signal including lead acid, lithium and alkaline type batteries used in consumer products, electric vehicles, power backup, security, and fire alarm systems.
-
product
Earth/Ground Resistance Tester
DE-5030
Earth resistance range0~12 / 0~120 / 0~1200 Normal operation conditionsBattery voltagein range of "BATT.GOOD" Earth voltage measurementmax. AC 30V Output current3mA Response timewithin 1 sec. Insulation resistancemin. 100M / DC1000V between input terminals and case Withstand voltageAC3700V (50 / 60Hz) for 1 min. between input terminals and case Battery Check Battery1.5V x 4 Safety standardIEC 61010-1 CAT.III 300V IEC 61557, IEC61010-031
-
product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 4.09k Ohm
40-294-023
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
S2 Unicolor Digital Sensors
ULP-S2 SCC
The Universal LightProbe S2 Unicolor Digital Sensor is pre-programmed to respond only to a specific color LED, including blue, green, yellow, orange, red, plus white. The Universal LightProbe S2 Unicolor Digital Sensor is designed for the simple ON/OFF test and color check of a single color LED, with a digital output, quickly determining PASS/FAIL status without further processing by Automatic Test Equipment. The Universal LightProbe S2 Unicolor Digital sensor provides the simplest and fastest interface to Automatic Test Equipment (ATE).Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts, at 6mA max.; less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times: <10mS capture time; <65mS overall response timeFiber-Optic Probes: Can utilize any Universal LightProbe Fiber-Optic Probe
-
product
PXIe-4162, 12-Channel, ±24 V, Precision PXI Source Measure Unit
785680-01
PXIe, 12-Channel, ±24 V, Precision PXI Source Measure Unit - The PXIe-4162 is a high-precision, high-density source measure unit (SMU) with 12 identical SMU channels. This module features 4-quadrant operation, integrated remote (4 wire) sensing in each channel for accurate measurements, as well as analog-to-digital converter technology to help you perform high-precision measurements. It also features guard terminals to remove the effects of leakage currents and parasitic capacitances. Additionally, the PXIe-4162 can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4162 is ideal for a broad range of mixed-signal integrated circuits (ICs) in semiconductor production test.
-
product
Field Strength Meter
FIM-72A UHF
The Model FIM-72A is a portable, laboratory quality Field Strength Meter designed for rigorous field applications. Combining a calibrated half-wave dipole antenna and a highly accurate tuned voltmeter with a range of 140 dB, the FIM-72A is suitable for practically all types of RF emission measurements in the 450 MHz to 960 MHz spectrum. The operator can switch select wide or narrow bandwidth, peak or average value of TV or pulse modulated signals, AM or FM demodulation, and meter dynamic range of either 20 dB or 60 dB. A dc analog voltage, proportional to meter indication, is provided for driving a chart recorder or similar device. A leveled output from the calibrating generator is available for measuring cable insertion loss, filter response, amplifier gain, VSWR, and other signal ratio measurements. The 4-1/2 inch, taut band, mirrored scale meter is calibrated in volts and dB for precise measurements in field or laboratory environments.
-
product
Low-Pass Filters
Is a filter that passes signals with a frequency lower than a selected cutoff frequency and attenuates signals with frequencies higher than the cutoff frequency. The exact frequency response of the filter depends on the filter design.
-
product
Photo Detectors
Vishay has the broadest portfolio of PIN photobodies on the market. Vishay's photo detectors, photo transistors, and light detectors offer lower capacitance, provide high-speed response, and low noise and low dark current along with excellent sensitivity. They are ideal for high-speed data transfer, light barriers, alarm systems, and linear light measurement.
-
product
Temperature Indicator
Aarohi Embedded Systems Pvt. Ltd
Aarohi develop special temperature indicator for motor & pump testing with high accuracy. Micro controller based design provide fast response, precise measurement & easy compatibility with data acquisition system
