Showing results: 1591 - 1605 of 1676 items found.
-
Excalibur Systems, Inc.
The M4K-ETH is an intelligent Gigabit Ethernet interface module for the multiprotocol Excalibur 4000 family of carrier boards (only 64 bit versions). The module supports 10Mhz, 100Mhz and 1Ghz Full Duplex UDP/IP Ethernet.The receive channels allow for the storage of all packets to all MAC and IP addresses with status and Time Tag information appended to each packet. The receivers allow for filtering based on MAC address, IP address and UDP port. The transmit channels enable the user to define a Bus list which controls timing and order of packets without host intervention or immediate mode which enables the host to transmit packets at will.
-
CL-300 -
Schonstedt Instrument Co.
The NEW CL300 cable locating kit consists of a portable, holstered pipe & cable locator with an industry accepted 33kHz transmitted frequency. Comes standard with 512 Hz detection capability. With an added 512Hz transmitted device or traceable duct rodder the CL300 becomes the perfect tool for empty duct work locating. This instrument is capable of detecting all electrical, telecommunications and wire circuits—whether direct buried cables or those within conduits—using direct connect or close induction methods. This locator equipment features Auto & Manual adjustments for both transmitter power and receiver sensitivity to assist with a variety of locate work and congestion.Applications
-
6152 & 6152C -
AYA-Instruments
*Refresh Rate – A packet of data is sent from the outdoor transmitter to the receiver every 2 1/2 seconds! This means when you look out the window and see the wind blowing, the weather station will reflect it almost immediately.*Transmission Distance (wireless models) – The first in its consumer price range to use frequency hopping spread spectrum radio technology, the Vantage Pro2 can transmit and receive data up to 1000′ (300 m) line of sight. This is a much greater distance than most other weather stations. This technology also provides improved reception through multiple walls and greater immunity from RF interference.
-
R15-EC -
Abaco Systems Inc
The R15-EC card provides the highest level of performance and density for MIL-STD-1553A/B in an ExpressCard form factor. The R15-EC card provides 1 or 2 channels integrated with powerful API software that provides instant access to all 1553 databus functionality and data. Standard features include real-time bus playback (with ability to edit out RTs), aperiodic message insertion, error injection/detection, conditional BC branching, 64-bit, 25 nanosecond message timetagging, and “Oneshot” BC operation. The Bus Monitor mode provides 100% bus monitoring of a fully loaded 1553 bus. IRIG-B Receiver (AM or DC/TTL) Generator (DC/TTL) optionally available.
-
S930907B -
Keysight Technologies
The S930907B spectrum analysis (SA) adds high-performance microwave spectrum analysis to the N522xB/N524xB PNA family up to 70 GHz. With fast stepped-FFT sweeps resulting from optimized data processing, the SA application provides quick spurious searches over broad frequency ranges. Simultaneous spectrum measurements can be done using up to five test and reference receivers. This multi-channel SA can be used with the internal swept-signal generators for efficient measurements of spurious signals emanating from mixers and frequency converters. The SA application employs source-power and receiver-response calibration as well as fixture de-embedding, providing in-fixture and on-wafer spectrum measurements with the highest level of accuracy.
-
S930902B -
Keysight Technologies
The S930902B spectrum analysis adds high-performance microwave spectrum analysis to the PNA family up to 26.5 GHz. With fast stepped-FFT sweeps resulting from optimized data processing, the SA application provides quick spurious searches over broad frequency ranges. Simultaneous spectrum measurements can be done using up to five test and reference receivers. This multi-channel SA can be used with the internal swept-signal generators for efficient measurements of spurious signals emanating from mixers and frequency converters. The SA application employs source-power and receiver-response calibration as well as fixture de-embedding, providing in-fixture and on-wafer spectrum measurements with the highest level of accuracy.
-
165 CB -
Standard Electric Works Co., Ltd
● 165 CB is an ideal tool which can test the correct pin configuration for different kinds of cables.● For testing: -RJ45/RJ11 -USB -COAX -BNC cable -Multi-wire cable● Auto-scan and manual-check function● Buzzer sound warning for wire status● 2 LED module indicators on the master unit which can do both of transmitter and receiver functions for RJ45/RJ11 cable testing. Users don't need to use the receiving unit.● 165 CB provides a variety for checking cable continuity, open status, short status and miss-wired. ● Ground (shielded ) wire test.● LED indication for wire status.● Power source : 9V battery
-
S94610B -
Keysight Technologies
Digital Wideband Transceiver Analysis is an add-on software to Device Measurement eXpert (DMX) that adds cross-domain stimulus response measurements for digital/RF mixed-signal device characterization. Included Waveform Creator helps define digital IQ test stimulus waveforms that are used in the RF signal generators for receiver tests or downloaded to the digital-to-analog converters for transmitter tests. The DUT control is customizable to accommodate various data converters and transceiver types by defining device operation settings, transmit/receive switching, reading and writing digital IQ waveform from and to DUTs. Acquired RF or digital data is processed in the VNA’s applications for faster, accurate measurements and analysis.
-
S930901B -
Keysight Technologies
The S930901B spectrum analysis adds high-performance microwave spectrum analysis to the PNA family up to 13.5 GHz. With fast stepped-FFT sweeps resulting from optimized data processing, the SA application provides quick spurious searches over broad frequency ranges. Simultaneous spectrum measurements can be done using up to five test and reference receivers. This multi-channel SA can be used with the internal swept-signal generators for efficient measurements of spurious signals emanating from mixers and frequency converters. The SA application employs source-power and receiver-response calibration as well as fixture de-embedding, providing in-fixture and on-wafer spectrum measurements with the highest level of accuracy.
-
2960AR and 2965AR -
Novatech Instruments , Inc.
The 2960AR has a rubidium timebase and provides two 10MHz and one 5MHz sine wave outputs. The 2965AR has a rubidium timebase and provides one 10MHz, one 5MHz and one signal generator output. The signal generator output uses Direct Digital Synthesizer (DDS) technology and is programmable from 100Hz to 50MHz via an RS232 serial interface. Both models can be disciplined by a 1pps input signal and provide a 1pps output. The 1pps input is typically provided by the GPS Frequency output from a device like a smart GPS receiver or antenna. The Novatech GPS1 Smart Antenna is available as an accessory to provide a complete turnkey solution.
-
Satlook Color HD -
Emitor AB
Spectrum-analyzer 950-2150MHz. • DVB/S S/2 -receiver 920-2150MHz. • Super bright 5" 16:9 TFT-LCD color display. • Automatic Satellite identification. • Readout of NIT - gives SAT ID and TV/Radio-channel info. • Digital BER and S/N-ratio (DVB-S, S/2). • QPSK and 8PSK constellation diagram. • DVB-S (Free to Air) and SAT-analog TV-picture. • LNB voltage 13/18V, 22KHz tone switch. • DiSEqC according to level 1.0, 1.1 and 1.2. • SatCr-control (UniCable). • Favourite channel list (100 channels) for FTA DVB-S. • Lots of memory positions for spectrum pictures. • RS232 for PC-connection (up/download). • Rechargeable Li-Ion battery.
-
S960904B -
Keysight Technologies
The Keysight S960904 spectrum analyzer (SA) software application adds high-performance spectrum analysis to the E5081A ENA-X up to 20 GHz. With fast-stepped FFT sweeps resulting from optimized data processing, the SA software application provides quick spurious searches over broad frequency ranges. The application enables simultaneous spectrum measurements using test and reference receivers. The multichannel SA pairs with the internal swept-signal generators for efficient measurements of spurious signals emanating from mixers and frequency converters. The SA application uses source-power and receiver-response calibration and fixture de-embedding, providing highly accurate in-fixture and on-wafer spectrum measurements.
-
Narda Safety Test Solutions
Real-Time Outdoor Remote Analyzer for the Detection, Analysis, Classification and Localization of RF Signals between 8 kHz and 8 GHz. Supports automatic direction finding and localization via AoA and TDOA. For fixed installation or semi-static use on demand. Solves complex measurement and analysis tasks reliably and quickly with outstanding RF performance. Windows 10-based open platform for third-party applications. The "SignalShark 3330 Outdoor Unit" series is characterized by a robust and weatherproof die-cast aluminum housing with IP65 protection class, which is also used as a heat sink. The compact size allows the receiver to be mounted close to the antennas, keeping the antenna cables short and the resulting sensitivity high.
-
Gauss Instruments
The EMI receiver families TDEMI® of GAUSS INSTRUMENTS® provide a huge fully CISPR compliant real-time bandwidth and therefore allow to speed up your measurements tremendously and to reduce the measurement uncertainty significantly - both at the same time. By using the full automation software suite EMI64k from GAUSS INSTRUMENTS the test procedures according to the CISPR 16-2-3 standard for the FFT-based measuring instruments as well as conventional testing (pre-scan and final maximization) and further EMC Standards are available. In comparison to the previously conventional pre-scan and final measurement strategy, the overall test quality can be significantly increased whereas the testing times are reduced by orders of magnitudes.
-
882EA-DP -
Teledyne LeCroy quantumdata
The Teledyne LeCroy quantumdata 882EA-DP test instrument with both a DisplayPort 1.1 transmitter and receiver (analyzer) option is packed with features for video and audio testing of DisplayPort monitors and sources at pixel rates up to 268 MHz. The 882EA-DP test instrument provides two (2) additional DisplayPort ports for passive monitoring of the link layer through the optional Aux Channel Analyzer (ACA) application. The ACA option enables you to monitor link training transactions either between the instruments Tx port or its Rx port with the DisplayPort device under test. The 882EA-DP instrument can optionally be equipped with industry approved compliance tests for Link Layer, EDID and HDCP 1.2.
