Showing results: 46 - 60 of 123 items found.
-
Textron Systems
Textron Systems’ commercial RF Sources (RFS 340, SSI) provide an unmatched combination of frequency coverage, power range, signal fidelity and switching speed in either a two-slot VXI, 1U LXI®, or VME Synthetic Stimulus Instruments (SSI) format.
-
Keysight Technologies
Keysight Technologies offers the most comprehensive portfolio of stimulus solutions for the generation of digital and analog waveforms and data signals. The Keysight instruments cover a frequency range from 1 μHz to 56 Gb/s and an output amplitude range from 50 mV to 20V.
-
NTE-2A -
Physitemp Instruments
The NTE-2A Thermal Probe is a sophisticated, non-invasive device for the clinical evaluation of neuropathy and the assessment of short fiber neurological function. Individual thresholds are compared to normals to statistical normals. These results provide an accurate means of tracking chronic changes in small fiber nerve function. It can be used for pain studies and in any application were a variable, accurately-controlled temperature stimulus is required. The NTE-2A is often used in conjunction with the Vibratron II to assess peripheral neuropathies.
-
Metis -
Afore
METIS is a motion simulator for sensor and end system level testing. Configurable design allows you to create system you need! - 1-axis rate table for gyro testing - 2-axis unit for 6DOF accelerometer and gyroscope testing - 3-axis Gimbal system for simultaneus Yaw, Pitch and Roll stimulus.
-
Nexus Technology, Inc.
This product enables passive monitoring, debugging, and target system analysis of all speeds of Serial RapidIO Gen2 and Gen1 from the physical coding-sublayer (PCS), through serial protocol, to full-duplex link protocol exchanges. Stimulus transmitters allow for injection of SRIO packets, control symbols, and 8b/10b characters.
-
65DL2 -
North Atlantic Industries
NAI’s 65DL2 is a 12-channel, 3-wire, LVDT/RVDT Simulation Instrument on a VXI board. This single-slot, message-based board features up to 12 stimulus channels of 3-wire LVDT/RVDT, wraparound self-test, and onboard programmable excitation supply. The board is uniquely versatile, as each excitation input and output voltage is programmable. In addition, each channel can be programmed to be controlled by an external DC voltage. A replacement for the 5410C-83, the 65DL2 is ideally suited for defense, commercial aerospace, and industrial applications.
-
GT98901 Series -
Marvin Test Solutions, Inc.
The GT98901 Demo board is a USB controlled, cost-effective, multi-function PCB assembly. The module is completely self-contained and includes an LCD display, measurement and stimulus resources, digital I/O, relays, and switches – all of which can be accessed and monitored via the USB port using a SCPI command set via a USBTMC interface which supports the USB488 protocol. Power for the board is provided via the USB interface, providing a totally self-contained assembly which can provide users with a simple yet complete vehicle that replicates many of the stimulus and measurement functions associated with ATE systems. When combined with Marvin Test Solutions' ATEasy® Test Executive and Test Development environment, the GT98901 is the ideal product for creating and supporting ATE training and education applications.
-
DP-cPCI-7554 -
Data Patterns Pvt. Ltd.
DP-cPCI-7554 is a cPCI module capable of analyzing the phase and gain characteristics of a system. The system under test is stimulated by the user defined waveform. The obtained response is correlated with the applied stimulus by the on-board DSP processor to determine the phase difference and the gain.Gain and the face analysis is carried out only at sine waveform.
-
1250E -
Ametek Scientific Instruments
The 1250E Frequency Response Analyzer (FRA) delivers accurate measurement of gain and phase. The device under test is stimulated by a sinewave and the response analyzed at various points in the system. These responses are then correlated with the stimulus to determine the amplitude and phase relative to the generator. The ratio of the two measured signals can then be used to provide the system transfer function.
-
N9000B -
Keysight Technologies
Master the essentials in signal characterization with the leading low-cost tool in signal analysis Perform cost-effective stimulus response measurements with the optional built-in tracking generator Add crucial functionality with X-Series measurement applications Enhance theory with practical skills when used with a training kit in your RF & microwave education lab
-
64CS4 -
North Atlantic Industries
NAI’s 64CS4 is a 6U VME multifunction I/O board designed for applications requiring Digital-to-Synchro/Resolver (D/S) stimulus output, as well as I/O and communication functions. This board contains five intelligent, function module slots. The board can be configured for 10 D/S channels, or for D/S in combination with I/O and communication modules. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
3152B -
Astronics Corporation
The Racal Instruments™ 3152B Waveform Synthesizer combines 250 MS/s waveform generation performance, versatility, and compact size into a single-slot VXIbus format.The 3152B is a greatly improved version of a fi eld-proven instrument ideal for VXI test stimulus generation. It replaces the 3152A which is standard on many military and commercial test platforms
-
RTB 3000 -
Santa Barbara Infrared, Inc.
The RTB 3000 Detector Test Bench from Santa Barbara Infrared (SBIR) is a flexible integrated IR detector test station for evaluation of single element detectors, linear arrays, and focal plane arrays. The RTB 3000 provides the radiometric stimulus necessary to perform accurate IR detector testing in both laboratory and production environments.
-
Accel-RF Corporation
This standalone integral software and hardware platform is capable of functioning as an independent single-channel or virtual multi-channel characterization test subsystem. The platform is USB controlled to provide temperature, RF-signal and bias-control to a device-under-test (DUT) for semiconductor performance measurement. When used in conjunction with Accel-RF's embedded Pulser-Card Assembly, the test device is capable of pulsed DC and RF stimulus.
-
GT98901 -
Terotest Systems Ltd.
The GXT98901 Demo board is a USB controlled, cost-effective, multi-function PCB assembly. The module is completely self-contained and includes an LCD display, measurement and stimulus resources, digital I/O, relays, and switches – all which can be accessed and monitored via the USB port using a SCPI command set via a USBTMC interface which supports the USB488 protocol.