Calibration
maintains accuracy of test asset by correcting out of specification conditions.
See Also: Calibrators, Power Calibration, Display Calibration, Calibration Standards, Calibration Software, Calibration Services, Calibration References
-
product
Standard Signal Isolating Amplifier
Knick Elektronische Messgeräte GmbH & Co. KG.
Isolation and conversion of standard signals. Calibrated switchable inputs and outputs 0/4 ... 20 mA and 0 ... 10 V signal duplicator with two electrically isolated outputs.
-
product
Reflectance Standards
STAN Series
Ocean Optics offers specular reflectance standards for measuring shiny surfaces such as machined metals and semiconductor materials and low-reflectivity surfaces such as anti-reflective coatings and thin film coatings. The STAN-SSH varies in reflectivity from 87%-98% over the 200-2500 nm wavelength range and is available in a version (STAN-SSH-NIST) calibrated to a NIST master standard. The NIST calibration data range is 250-2500 nm.
-
product
Calibration Segment Arm
A torque analyzer or a torque sensor are a finely tuned instrument designed for testing and monitoring torque applications. In order to maintain accuracy, it is crucial that torque measuring equipment be properly calibrated regularly. Segment arm is engineered for calibrating torque analyzers and sensors and ensuring instruments are traceable to National or International Standards, such as N.I.S.T and ISO.
-
product
RF Power Controller (ALC)
310-010030-004
The serial controlled ALC module is used to set and monitor the output level of your fixed gain RF amplifier. The module is available for many bands between 800 MHz and 3 GHz, and is configured and calibrated to meet your requirements.
-
product
NI-9262, 1 MS/s/ch Simultaneous, ±10 V, 6-Channel C Series Voltage Output Module
785503-01
1 MS/s/ch Simultaneous, ±10 V, 6-Channel C Series Voltage Output Module - The NI-9262 is a simultaneously updating analog output module. It features overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST-traceable calibration. The NI-9262 module includes a channel-to-earth ground isolation barrier for safety and noise immunity.
-
product
Industrial Calibrators
A temperature calibrator, often called a thermometer calibrator, is used to correct inaccuracies in installed thermometers and temperature sensors, because temperature measurement is a critical parameter in many industrial processes. Although simulators are sometimes called temperature calibrators or thermometer calibrators and may be used to provide thermometer calibration for the electronics in an installed system, a temperature source with a calibrated reference sensor is still required to provide a complete and meaningful calibration. Fluke Calibration industrial and field temperature calibrators include: Metrology Wells; Field Metrology Wells; field dry-well calibrators; handheld dry block calibrators; Micro-Baths; large target infrared calibrators; field IR calibrators; ice-point dry-well; and thermocouple furnaces.
-
product
Fixed Attenuator
FAXE
Fixed Attenuators are waveguide components for introduction of some particular attenuation value in to the waveguide network for signal leveling or reflection compensation. The attenuators have two types of design: with resistive plate in the waveguide diagonal plane or using coupling technology. The FAXE 3, 6, 10, 15, 20, 30 dB attenuators are available in waveguide bands from 18 through 225 GHz. The FAXE Fixed Attenuators can be used as laboratory Standards against which other instruments or devices are calibrated in case the parameters of these Fixed Attenuators are stable enough and were measured with appropriate accuracy.
-
product
Footspacing Kit
10759A
The Keysight 10759A Foots pacing Kit, included in the Keysight 55282A Flatness Accessory Kit, provides three precision baseplates with 50.8 mm (2 in), 101.6 mm (4 in) and 152.4 mm (6 in) pad spacing. As an accessory to the Keysight 5530Laser Calibration System, the kit simplifies the mounting of the flatness mirror used in flatness measurement applications. The Keysight 10759A minimizes the grid setup and data accumulation time required for plate calibration.
-
product
Meter Testing System
ASTel
Three-phase Meter Test Equipment of ASTeL 3.2x.x series system is a fully automatic system enabling simultaneous, multi-position calibration and legalization of electric energy meters. The automatics include power sources, reference standards, stand controllers, photoelectric scanning heads, separating transformers, and other elements of the system. All these elements are controlled through a Windows based executive program.
-
product
Electrical Calibrators
An electrical calibrator, or dc calibrator from Fluke Calibration includes many innovative and multi-functional solutions to help laboratories operate efficiently, increase throughput, and comply with today’s quality standards. Versatile models and options provide a wide range of possibilities to match a variety of workloads and budgets. Electrical calibrators include: Multi-product calibrators; multifunction calibrators; oscilloscope calibrators; power calibrators; pressure/temperature calibrators.
-
product
Test DVD For OmniMic Precision Measurement Systems
OMDVD Version 1
The Dayton Audio OMDVD Test DVD brings the ease of the OmniMic V2 system to measurements of 5.1-channel audio systems. It’s the essential tool for professional installers and home theater enthusiasts to ensure proper audio calibration and optimization of a home theater or multichannel music system for the highest possible performance. The full functionality of the OmniMic V2 measurement system is now available through every channel of a 5.1-channel audio system thanks to the OMDVD Test DVD’s suite of high-quality test tones, and an intuitive menu structure that has been optimized for ease of use.
-
product
Level System
Universal II
The Universal II level transmitter offers increased reliability, low maintenance and an intrinsically safe design for dependable level measurements in all kinds of process liquids, slurries, granulars and interfaces.Universal IIThe Universal II is a two wire level transmitter that eliminates the need for line power in the field and saves costs for additional hardware. It provides reliable level measurements in all kinds of process liquids, slurries, granulars and interfaces.When powered from an approved source this level transmitter can be made intrinsically safe. Its rugged contruction resists corrosion and abraision. The no moving parts design eliminates break downs.The Universal II level transmitter utilizes RF Admittance technology with manual calibration and a 4 – 20 mA output signal. The patented Cote-Shield circuitry ensures accuracy and reliability regardless of product build-up on the level transmitter.This level system is unaffected by changes in the process material density, pressure, or temperature variations.
-
product
Dimensional Calibration
Process Instruments certifies Gage Blocks with a state-of-the-art Pratt & Whitney Gage Block Comparator. Outside and Inside Micrometers, Depth Micrometers, Height Gages, Calipers and Dial Indicators can be repaired and calibrated to manufacturers'' specs.
-
product
LCR Meter
M162
M162 LCR meter is a great complimentary tool to most multi-meters. Regular multi-meters are good in many way. But they usually have rather limited or even no ability for capacitance, inductance, and sub-ohm resistance measurement. The addition of a M162 LCR meter will overcome this deficiency. The DIY kit version of M162 is very easy to build. No special calibration is required to achieve ~1% accuracy.
-
product
Explosion-Proof Oxygen Transmitter
OxyTrans-EX
The Edgetech Instruments Model OxyTrans is an easy to use, accurate and economical way to measure Oxygen at trace and % levels. A simple display and one point calibration allows for a quick start of the instrument.
-
product
Handheld Calibrators
These handheld calibrators are perfect for calibrating thermocouples and RTD's in cases where the sensors are fixed or need to be calibrated on the spot. Locations such as factory floor or in the lab.
-
product
HUM DETECTOR (DEMODULATOR)
HD-500
Matrix Test Equipment Incorporated
The MATRIX Model HD-500 is a detector-amplifier designed to demodulate the low frequency amplitude modulations on any RF carrier over the range of 5 to 1500 MHz. These modulations are usually the undesirable result of the 50 or 60 Hz power source and are not necessarily sinusoidal. The unit is calibrated to the SCTE definition of hum modulation, which is the ratio of the peak-to-peak hum modulation to the peak of the carrier.
-
product
Current Sensing
voltage-output, current-sensing amplifier family that integrates an internal shunt resistor to enable high-accuracy current measurements at common-mode voltages that can vary from 0 V to 36 V, independent of the supply voltage. The device is a bidirectional, low- or high-side current-shunt monitor that allows an external reference to be used to measure current flowing in both directions through the internal current-sensing resistor sensor. The integration of the precision current-sensing resistor provides calibration equivalent measurement accuracy with ultra-low temperature drift performance and ensures an optimized Kelvin layout for the sensing resistor is always obtained.
-
product
3 Wire (Analogue) Earth Resistance Tester
1805 ER
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● Test test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Battery check function.● Calibration performed with supplied test leads.
-
product
Temperature Calibrators
Fluke Temperature Calibrators simulate process sensors for testing temperature instrumentation. Specifically designed for the field, these lightweight compact tools are EMI tolerant, dust and splash resistant and offer an easy to use single push button interface. When paired with a temperature sensor they can take high accuracy temperature measurements to verify process temperatures and ensure the highest product quality and safety. There are a variety of different temperature calibrators designed for your unique calibration and testing requirements.
-
product
PCI Strain Gauge Simulator Card, 2-Channel, 3k
50-265-102
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
Noise Generator
NG 600
The NG 500 noise generator is an external module with dual power supply for different applications: to calibrate filters, switchboards, to the distance of a fault caused by the impedance mismatch, to test the cable efficiency.
-
product
Automated Systems
At Tinius Olsen we have taken a fresh look at how our customers use materials testing machines and software to meet their specific needs in today’s commercial environment. Accuracy, resolution, data rates, control, precise adherence to test standards, calibration, measurement of uncertainty and traceability are all essential parameters tuned to the highest standards and capabilities in Tinius Olsen testing machines and software. We can configure an automated system to match your exact requirements, saving time and making you money.
-
product
Decade Capacitor
GenRad 1423-A
The GenRad 1423 decade capacitor is a versatile tool for calibration laboratories and production-line testing. With it a bridge can be standardized to an accuracy exceeded only by that of the highest quality, individually certified laboratory standards such as the GR 1404 Reference Standard Capacitors.Used with a limit bridge, such as the GR 1689 Digibridge, the 1423 facilities fast and accurate production-line measurements of arbitrary capacitancevalues with minimum setup time.
-
product
Bluetooth® Enabled Dissolved Oxygen (DO) & Temperature Pen
UltrapenX2™ PTBT5
*Industry Leading Accuracy*Display DO in Concentration, % Saturation, or Both*Adjustable for Altitude and Salinity*3 Calibration Methods: Air, Water and 0 ppm DO*Dynamic Membrane Temperature Correction*Measurement Storage with Time, Date and Location*Export Stored Measurement Data Via Email*Live or Hold Mode – User Selectable*Proprietary Sensor Design*Rugged Design with Aircraft Aluminum Body*Durable, Epoxy Encapsulated ElectronicsWaterproofPowered by One N Type Battery (Included)
-
product
High Precision Compression Type Load Cell
ZR
A high-precision compression-type load cell is a sensor that accurately measures compressive (pushing) forces, designed for applications requiring very tight accuracy and reliability. It works by converting a downward force into an electrical signal, often using strain gauges to measure deformation, and is used in demanding fields like calibration, manufacturing, and medical equipment.
-
product
Calibrators
Portable and user friendly calibrator, ideal for checking sound level meters and dosimeters on the measurement site, or in the laboratory.
-
product
Hardness Test Blocks
Used to verify the hardness tester's performance and provide data in order to calibrate the hardness tester.
-
product
Temperature Calibrators
We offer temperature calibrators in different shapes. We offer temperature dry blocks that can generate an accurate temperature, for example for temperature sensor calibration. We also offer electrical temperature calibrators that can measure and simulate various temperature sensors (RTDs and thermocouples). We also offer high-accuracy reference temperature probes.
-
product
Humidity Generator
VAPORTRON®
Buck Research Instruments, LLC
The Vaportron is a humidity generator for calibrating a wide variety of humidity sensors. It is extremely accurate and stable over a wide range of temperatures and humidities. It has numerous options for a wide variety of calibration applications.
