Counting
-
product
PXI/PXIe Very High Density Multiplexer, 198-Channel, 1-Pole
40-675B-002-198/1
The 40-675B-002-198/1 (PXI) and the 42-675B-002-198/1 (PXIe) are 198-channel, 1-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems.
-
product
Wireless In-Circuit Test Fixtures
Higher density more complex circuit boards complicate testing requirements while smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in standard long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board or T-Board®. Circuit Check’s wireless fixture technologies reduce test program debug and maintenance times while easing the ECO process. Thus allowing for the higher level of test performance, the ability to probe smaller denser targets and achieve ultra-high node counts.
-
product
PXI/PXIe High Voltage Multiplexer, Dual 23-Channel, 1-Pole
40-321-108-HI
The 40-321-108-HI (PXI) and 42-321-108-HI (PXIe) are dual 23-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
product
LXI WTB Adaptor, Terminated
60-982-002
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
product
500W to 2000W - Single Output
ALE-OEM Series
*Reduced package size*New patented inverter*On-board PFC*Reduced parts count*Remote control*High EMI-RFI immunity*Medical safety approvals
-
product
FMC for High Speed Optical Communication Dual QSFP+ FMC
FMC424
Sundance Multiprocessor Technology Ltd.
The FMC424 is a dual QSFP+ FPGA Mezzanine Card. Electrically compliant with the VITA 57.1 standard the FMC424 is compatible with 4DSP FPGA carrier cards offering High Pin Count connectors. It also allows for the option to stack an additional FMC over it. Any of the 4DSP FMC that use LVDS and single ended signaling only can be mounted over the FMC424, thus offering users with the ability to build a complete high speed data acquisition, waveform generation and optical communication solution while using a single FMC site on an FPGA carrier card.
-
product
Wireless Connectivity Digital Multimeter 4000 Count / NCD / SPT / Wide Frequency
MS-WP4DMM1E
This is a compact, slim, light weight, pocket size external wireless connectivity Digital Multimeter integrated with 4000 Count, True RMS auto and manual measurement.
-
product
Power Clamp Meters (TRMS)
2736
Kusam Electrical Industries Limited
Voltage Function : 6000 counts LCD display Power, Ohm & Hz functions : 9999 counts LCD display, ACA clamp-on function : 4000 counts LCD display
-
product
Density Meter
Count on solutions from the source – Anton Paar has always been at the forefront of innovation in laboratory density and concentration measurement ever since we introduced the world’s first digital density meter. Today we offer a whole series of density meters, covering most requirements in various industries and R&D – from instruments with three-digit accuracy to the world’s most precise six-digit density meter, from handhelds to benchtop instruments. Anton Paar offers the right instrument for every application requirement – choose the density meter that best fits your needs.
-
product
CamTrac Z-Axis Test Fixture Kits
CT Serie
The CT Series Mechanical Kits, utilizing the patented CAM mechanism1, offset the same precision linear motion. The 'Z' axis motion is ideal for a larger point count mechanical test applications.The CT Series features a hinged 3/8" FR4 probe board, tooling holes for precision alignment, removable sides, precision shafts and cam slide block assemblies, and a pan latch assembly.
-
product
3 3/4 Digit Autoranging Digital Multimeter w/Bargraph
HH2204
High Accuracy (Basic Accuracy 0.5%). Jumbo LCD display 3260 count, 27mm figure height. Auto Ranging or Manual Ranging at your choice. Higher Voltage test up to AC 750V and DC 1000V. Higher Current test up to 20A. Resistance test up to 30MΩ. Frequency test range up to 3000Hz. Diode test, audible continuity check and Transistor test
-
product
IP Pulse
IP Compatible card with 4 programmable pulse generators. TTL or RS422 / RS485 compatible outputs. Programmable pulse - nS to seconds. Programmable count or free
-
product
PXI-2575, 196‐Channel, 1-Wire PXI Multiplexer Switch Module
778572-75
196‐Channel, 1-Wire PXI Multiplexer Switch Module —The PXI‑2575 is a high‐density PXI multiplexer switch module that is ideal for high‑channel‑count automated test applications. It uses electromechanical relays and can route hundreds of signals to measurement devices or from source units. The PXI‑2575 also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
Digital Multimeter
6420 DM
Standard Electric Works Co., Ltd
● 4000 counts LCD with a maximum display of 3999.● Angled display design helps the user to identify the reading of value easier.● Auto ranging designed.● Bar graph LCD display.● Range change function.● Relative/Maximum/Minimum modes.● Peak hold mode.● VAHz mode measures frequency in voltage or current mode.● 40M Hz frequency counter.● Auto Power off.● Continuity check.● Data hold function.● Low battery indication.● Over range indication.● Fuse protection.● Special hook design used to hang the meter for ease of use.
-
product
PXI 3A Power MUX BRIC, 4-Channel, 24-Pole
40-571-102
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
PXI Programmable Resistor Module 18x8 Bit, 0 Ohm to 255 Ohm
40-295-121-18/8
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
product
Autoranging Digital Multimeter
HH2205L
High Accuracy 0.8%. Jumbo LCD display 4000 count, 22mm figure heigh. Full Auto Ranging with symbolic display. Rated CAT II 1000V. High Voltage test up to AC 750V and DC 1000V. Higher Current test up to 10A (fuse protected)
-
product
Advanced Multimeter
7117
Peaceful Thriving Enterprise Co Ltd
This is a low power consumption, high accuracy and stable hand held 6000 counts multi-meter; with special designed IC to support true RMS measurement. It performs measurements of DC voltage/current, true RMS AC voltage/current, resistance, capacitance, frequency, diode, continuity, temperature and non-contact voltage sensing.
-
-
product
Bidirectional Weight Indicator
480
Large 0.8 in LED 6-digit Display• 100,000 displayed graduations• 523,000 internal counts• Powers up to 10 Load Cells• Tension/Compression operation• NEMA 4X stainless steel enclosure• Measurement Rate up to 40Hz• Selectable filter settings• 0.1uV/graduation signal sensitivity
-
product
PXI BRIC4 FIBO Matrix Dual 31x4 2pin brkout
40-592A-011
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
Bench Digital Multimeters
High accuracy Bench HMM with Interface4000 counts LCD display with 42-segment bargraph, backlit and unity annunciators.AC/DC powered allows carrying to the site built in storage compartment for accessories True RMS AC current/voltage measurement
-
product
Rapid Test Development
TestEZ® Development Suite
Count on the Test EZ® Development Suite for complete, efficient, cost-effective test development and execution for electronic test systems.
-
product
Clamp on Meters
2000 counts LCD displayData hold for easy readingAuto-power offSafety as per IEC1010-1, Cat.II 1000V
-
product
PXI-2597, 26.5 GHz, 50 Ω, 6x1 (SP6T) Terminated PXI RF Multiplexer Switch Module
778572-97
26.5 GHz, 50 Ω, 6x1 (SP6T) Terminated PXI RF Multiplexer Switch Module—The PXI‑2597 is ideal for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules. The internal termination of the PXI‑2597 helps prevent high-power reflections that arise from open channels on the module. You can use the PXI‑2597 onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
Multiple-Input Multiple-Output (MIMO) FRF Testing
EDM Modal MIMO FRF Testing includes a dedicated test setup and operation process flow using multiple simultaneous shakers to acquire FRF signals. Using a large channel count data acquisition system (i.e., Spider- 80X or Spider-80Xi), this shaker excitation method provides much higher efficiency and accuracy for the FRF measurements while minimizing local stresses on the test article.
-
product
Tachometers, Counters & Displays
Displays Include; Rate, Time In Process, Product, Sum, Difference, Ratio, Draw Process, Batch, or Total Counting. Field Adjustable, Full Diagnostic Functions. Built-In Relay Testing Capabilities. Highly Programmable. Single-Channel or Bi-Directional Counting. Setpoint and Start Delay Functions. Multiple Relay and Analog Output Options. Keypad Lockout
-
product
PXI 3A Power MUX BRIC, 15-Channel, 16-Pole
40-571-205
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
PXI FlexRIO Signal Generator
The PXI FlexRIO Signal Generator combines analog I/O and a user-programmable FPGA into a single, customizable instrument. The instrument enables RF signal generation up to 2.9 GHz with 12 bits of resolution. The PXI FlexRIO Signal Generator uses FPGAs from Xilinx alongside LabVIEW and Vivado programming options for custom algorithm implementation and real-time signal processing. Using this instrument with NI-TClk, you can synchronize modules in one or more PXI chassis at up to picosecond‐level accuracy for high‐channel‐count applications.
-
product
Digital Fiber Multiplexers & Wavelength Shifters
FiberSaver Series
We don’t always have unlimited amounts of fiber at our disposal. Whether working in pre-fibered event venues, houses of worship or moving camera signals across busy metropolitan areas, fiber counts can quickly add up – especially when bi-directional optical transmission is required. MultiDyne’s FiberSaver Series is built for the system designer who needs a robust yet compact solution for signal links where fiber strands are limited, or where fiber feed requirements exceed budgets. FiberSaver products help technicians send and receive more optical signals over fewer fibers. Wavelength-agnostic inputs will multiplex just about any digital optical coming from SMPTE cameras, Network Switches, etc., and combine them with several optical matrix inputs. Scalable in increments of six channels, content producers now have a cost-effective solution to carry extra signals for sports production, distance learning and remote broadcasting.
