Synchronization
See Also: Synchronizers
-
Product
Dual Channel Multi-function Decommutator
LS-55-DD
-
The Lumistar LS-55-DD PCI Dual Multi-function PCM Decommutator offers two multifunction decoms and two optional bit synchronizers (LS-45) in a single PCI card slot. The multi-function decoms are implemented in FPGA using a next generation design based on the LS-50-P. The simulators,decommutators, time code reader and time code generator are achieved on the main board and the bit synchronizer is achieved through a low-profile daughterboard. CVSD voice, h.261 video, and IRIG Chapter 8 decoding are achieved through software.
-
Product
PCI-6110, 4 AI (12-Bit, 5 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device Multifunction I/O Device
777475-01
Multifunction I/O
4 AI (12-Bit, 5 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device - The PCI‑6110 is a simultaneous-sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6110 is ideal for a variety of applications, such as stimulus/response applications that require synchronization among analog input (AI), analog output (AO), and digital I/O. It is also ideal for 42 V automotive applications, radar, sonar, and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6110 dimensions require chassis slots that can accommodate full-length PCI modules.
-
Product
WAN Adapters
FarSync T2Ee
-
The FarSync T2Ee PCIe card provides high performance 2 port low profile synchronous communications with multiple signalling modes for Linux and Windows systems.
-
Product
2nd Generation PCI Multi-function Decommutator
LS-50-D
-
The Lumistar LS-50-D PCI Multi-function PCM Decommutator offers a PCM decom, PCM simulator, time code reader/generator, and optional bit synchronizer in a single short PCI card slot. The multi-function decom and simulator are implemented in FPGA using a next generation design based on the LS-50-P. The simulator, decommutator, time code reader and time code generator are achieved on the main board and the bit synchronizer is achieved through an optional low-profile daughterboard. CVSD voice decoding, h.261 video decoding, and IRIG Chapter 8 decoding are achieved through software.
-
Product
65 GSa/s Arbitrary Waveform Generator
M8195A
Arbitrary Waveform Generator
Sample rate up to 65 GSa/s High channel density: 1, 2 or 4 channels per module, synchronization of up to 16 channels on 4 modules with the M8197A multi-channel synchronization module Built-in frequency and phase response calibration Embedded DSP enables real-time waveform and impairment generation(in conjunction with the 81195A optical modulation generator software)
-
Product
Airborne Receivers & Bit Synchronizers
-
The Lumistar LS-28-DRSM Series Multi-Mode Multi-Band Receiver/Combiner/TM Processing Unit is designed using ruggedized packaging to survive severe airborne conditions. The LS-28-DRSM is available in several configurations: 1) Airborne receiver only (RF to bits), 2) Airborne bit synchronizer only, 3) RF to TM Processing and Display (RF to bits to UDP decom to LAN Client Displays). Models with receivers are available in any band form 200 MHz to 7 GHz with S, lower L and C bands as standards. Other RF bands are available, please consult the factory for details. This unit can be mated with other Lumistar products to provide a complete air-to-ground re-transmission system.
-
Product
6-Channel 200 MHz A/D and 4-Channel 800 MHz D/A with Virtex-7 FPGA - 6U VPX
Model 58720
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Three or six 200 MHz 16-bit A/Ds- One or two DUCs (Digital Upconverters)- Two or four 800 MHz 16-bit D/As- 4 or 8 GB of DDR3 SDRAM Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connectionsto the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Automated Engine Testing System
-
Automated engine test system is intended for comprehensive testing of electrical motors with shaft rotation frequency up to 70 000 rpm. Such engines include:*high-voltage motors;*traction engines;*internal combustion engines;*AC motors;*DC motors;*synchronous engines;*asynchronous engines;*asynchronous engines with short-circuit rotor.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 20 MS/s on 48 Channels
DN6.592-48
Digitizer
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
VFD Dual-display 4 1/2-digit Digital Multimeter
-
Shenzhen Chuangxin Instruments Co., Ltd.
Digital multimeter TH1941 4 1/2-digit is voltage/ current /resistance tester with multi functions and low cost. The instrument can stably perform measurement at high speed as several times as other instruments at the same level. It provides excellent performance, such as maximum reading of 12,000 counts, maximum DC voltage accuracy of 0.02%, and low cost to give you a best choice. Having VFD dual-display with high brightness. TH1941can synchronously display measurement parameters, such as AC/DC voltage or current, AC voltage/current and frequency to improve measurement efficiency and display results clearly.
-
Product
4-Ch 500 MHz A/D with DDC & 4-Ch 800 MHz D/A with DUC, Virtex-6 FPGA - 6U VPX
Model 58651
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 500 MHz 12-bit A/Ds- Four multiband DDCs (digital downconverters)- Two DUCs (digital upconverters)- Four 800 MHz 16-bit D/As- Two multiboard programmable beamformers- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
AdvintDAQ™ Data Acquistion
MAKO
-
The Mako platform is based upon use of NI CompactDAQ (cDAQ) product line consisting of a chassis, NI C Series I/O modules, and a Windows host computer connected over USB, Ethernet, or Wi-Fi. Mako systems provide an easy, flexible, expandable platform to meet the needs of any electrical or sensor measurement system. They control the timing, synchronization, and data transfer between a host computer and up to eight (8) C Series I/O modules. A single Mako can manage multiple timing engines to run up to seven separate hardware-timed I/O tasks at different sample rates in the same system. Multiple units can also be daisy changed together for larger applications.
-
Product
Power System Recorder
TESLA LITE
-
ERLPhase Power Technologies Ltd
The new TESLA LITE is an economical user-friendly multi-timeframe power system recorder: Economical yet complete power system recording for custom applications in smaller substations. Easy to use intuitive software Simultaneous transient fault, dynamic swing and trend recording and event logging Fault location derived from single and calculated currents IRIG-B clock synchronization (modulated and unmodulated) Smallest footprint among recorders allows easy retrofit and installation 12 current, 6 voltage and 38 digital inputs
-
Product
2-CH Encoder Card With Real-time Trigger I/O
AX92352
-
*Synchronizes devices via real-time I/O*Applied to area scan and line scan applications
-
Product
DPX-LED Controllers
-
Enables vibrant, synchronized lighting with up to 4,096 LEDs, customizable patterns, and real-time adjustments - perfect for slot machine designs
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 1 Channel, High Voltage Outputs
M2P.6570-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
4-CH, 14/16-Bit, Up to 2MS/s Simultaneous-Sampling Multi-Function PXI Modules
PXI-2000 Series
-
ADLINIK PXI-2010, PXI-2005 and PXI-2006 are simultaneous-sampling multifunction PXI modules to meet a wide range of application requirements. These products can simultaneously sample 4 AI channels with differential input configurations to achieve maximum noise elimination. They also provide 2-CH 12-bit analog outputs with waveform generation capabilities, which can be performed together with analog input functions. If more analog input or output channels are required, multiple modules can be synchronized through the PXI trigger bus. This makes the PXI-2000 series ideal for stimulus/response tests. The PXI-2000 series also feature analog and digital triggering, 24-CH programmable digital I/O lines, and 2- CH 16-bit general-purpose timer/counters. The auto-calibration feature adjusts the gain and offset to a specified accuracy, eliminating the need to calibrate the modules by adjusting trimpots.
-
Product
cRIO-9805, 4-Port, 802.1AS Ethernet Switch Expansion Module for CompactRIO
786993-01
Module
4-Port, 802.1AS Ethernet Switch Expansion Module for CompactRIO - The cRIO-9805 is a 4-port Ethernet switch that provides additional ports with 802.1AS network synchronization capability over the 1000 Base-TX network interface. This module supports TCP/IP and UDP network protocols in DHCP + link-local, DHCP, static, and link-local network IP configurations. The cRIO-9805 auto-negotiates communication rates of 10, 100, or 1000 Mbps with its four internally switched ports.
-
Product
IRIG-B TTL TO RS485 Converter
SPC - INS - 1010
-
Signals & Systems India Private Limited
The IRIG-B TTL signal is a time synchronization protocol that can be transmitted up to 50m maximum using coaxial cable. So the relay which is to be received the IRIG-B TTL signal may be far away from the IRIG-B source. The relay may be not able to synchronize with the GPS. To avoid such an incident in the field, some of the relays have provision to receive IRIG-B RS485 signal. The IRIG-B RS485 signal can able travel up to 1200m without any booster. All Time source equipment may not be supplied with IRIG-B RS485 signal output. The converter will act as a bridge between GPS Time source and Relays for time synchronization.
-
Product
PXI-5124, 150 MHz, 200 MS/s, 12-Bit PXI Oscilloscope
778757-04
Oscilloscope
150 MHz, 200 MS/s, 12-Bit PXI Oscilloscope—The PXI‑5124 high-resolution PXI oscilloscope samples up to 200 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for both time-domain and frequency-domain applications that require high-resolution measurements with up to 150 MHz of analog bandwidth. The PXI‑5124 also features PXI synchronization and data streaming capabilities.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 4 Channels
M2P.6566-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
2-Ch 1 GHz A/D and D/A with Virtex-7 FPGA - 6U VPX
Model 58730
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One or two 1 GHz 12-bit A/D- One or two 1 GHz 16-bit D/A- 4 or 8 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface up to x8- Dual-µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
PCI Direct Digital Synthesizers
SYNTH300-TRIG-HS
-
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
Product
PXI Infrastructure PXI Mainframe / Components
OTP2 module no.182
Mainframe
PXI offers the optimal approach to validation and production testing. You can meet timing, synchronization, and throughput requirements across devices. PXI is a robust PC-based platform for measurement and automation systems, supported by software. PXI combines PCI electrical bus characteristics with CompactPCI's modular Eurocard packaging, and then adds special synchronization buses and important software functions.
-
Product
NI-9361, 32-Bit, 8-Channel C Series Counter Input Module
783407-01
Counter Input Module
32-Bit, 8-Channel C Series Counter Input Module - The NI‑9361 is a differential or single-ended input module. With this module, you can expand beyond the four counters in CompactDAQ to reach up to 64 counters per 8‑slot chassis. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal switchable 1 kΩ pull‑up resistor. The NI‑9361 counters can perform encoder position and velocity measurements. You can synchronize the counters with other analog, digital, and counter measurements in your chassis.
-
Product
IC-3173, 2.20 GHz Intel Core i7 Dual-Core Processor, 4-GigE Port, 2-USB 3.0 Port Industrial Controller
784970-01
Controller
The IC‑3173 is a high-performance, fanless industrial controller for developers who require a high level of processing power and connectivity for automation and control applications in extreme environments. The IC‑3173 provides connectivity for communication and synchronization to EtherCAT and Ethernet CompactRIO chassis, EtherCAT motion drives, GigE Vision and USB3 Vision cameras, and other automation equipment. In addition, this controller has onboard isolated, TTL, and differential digital I/O, so it can perform synchronization and control tasks without additional tethered I/O.
-
Product
PXIe-6672, TCXO PXI Synchronization Module
780063-01
Synchronization Module
PXIe, TCXO PXI Synchronization Module—The PXIe‑6672 is a system timing controller module. It can drive the PXI star trigger lines, import and export PXI backplane clocks and triggers, generate a high-resolution direct digital synthesis (DDS) clock, and generate a high-stability temperature-compensated crystal oscillator (TCXO) 10 MHz Reference Clock for instrumentation. The PXIe‑6672 allows you to synchronize multiple PXI Express systems, synchronize a PXI Express system with external instruments and equipment, and increase the accuracy of instruments within a PXI Express system.
-
Product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - 3U VPX
Model 52791
-
- Accepts RF Signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Two FPGA-based multiband digital downconverters- Xilinx Virtex-7 VX330T or VX690T FPGAs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x4- Clock/sync bus for multimodule synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
PXI Digital Reconfigurable I/O Module
ITA
PXI Digital Reconfigurable I/O Modules feature a user-programmable FPGA for onboard processing and flexible I/O operation. You can completely control the synchronization and timing of all signals and operations along with custom onboard decision making. The PXI Digital Reconfigurable I/O Module is suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware-in-the-loop (HIL) test, custom communications protocols, bit error rate testing, and other applications requiring precise timing and control.
-
Product
USB-6366, 8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
782263-01
Multifunction I/O
8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6366 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6366 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
