Nanosecond
-
Product
Nanosecond Pulsed Lasers
-
Our nanosecond pulsed lasers feature pulses in the ns range. For picosecond and femtosecond lasers please see Ultrafast Lasers.
-
Product
UV Nanosecond Lasers
-
355 nm wavelengthPower: 0.5W* to 5W*Air-cooled design, water cooled optionAll-in-one (AIO) single box design for 0.5 & 1W modelPatented intracavity UV generationCompact, rugged, monolithic laser headTotal pulse controlTEM00 beam with typical M² < 1.2Pulse rates from 1Hz to 300kHzRS232 computer controlField replaceable pump diodes
-
Product
Diode Pumped Actively Q-switched Lasers
NL120 Series
-
NL120 series electro-optically Q-switched nanosecond Nd:YAG lasers provide up to 10 J per pulse with excellent stability. The innovative, diode‑pumped, self‑seeded master oscillator design results in Single Longitudinal Mode (SLM) output without the use of expensive narrow linewidth seed diodes and cavity‑locking electronics.
-
Product
Motor Termination Units
-
Since the rise time of IGBTs are in the range of a few tens of nanoseconds (between 50ns-200ns), even short cables between PWM motor drives and motors cause voltage doubling at the motor terminals due to Travelling Wave Phenomenon as in transmission lines. The insulation of motor windings are prone to failure due to high voltage spikes if necessary precautions are not sufficiently taken. RC Type Output Filter Modules reduce these high voltage spikes to protect motors by connecting to stator terminals.
-
Product
Jitter Free I/O Access Fast Data Acquisition
TiCoBasic
-
Shortest available reaction time for fast data acquisition, open- and closed-loop control! This focus of Jger Messtechnik is greatly intensified by the new TiCo processor, which enables real-time processing in the scale of nanoseconds. The TiCo (Timing Controller) being implemented into a Xilinx FPGA enhances the approved ADwin systems by a close-to-I/O, extremely fast pre-processing.
-
Product
Pulsed X-ray technology
-
Golden Engineering X-ray generators are based on Pulsed X-ray technology. Pulsed X-rays generate a high intensity X-ray burst (pulse) in a very short period of time (10 to 50 nanoseconds depending on the model). The output dose of each pulse is 3-6 mR measured 12 inches from the front of the X-ray generator. The operator varies the overall dose of each exposure by changing the pulse setting. The pulse rate varies from 10 pulses per second to 25 pulses per second depending on the model. The generators can fire up to 200 pulses before a four-minute rest period.
-
Product
*Tunable Wavelength
-
*Wide range of OPO and OPA systems*Ultra-broad tuning from 192 to 16 000 nm*Femtosecond, picosecond & nanosecond pulse durations*Narrow bandwidth models
-
Product
Single Photon Detector System For Near-Infrared (0.7 - 2.3 Um Wavelength)
-
*Frequency range includes coverage into higher frequencies than other photon counters on the market.*Short dead time (10 nanoseconds) compared to long dead time (microseconds) of alternatives. Therefore rapid repeition rate of 10s of MHz possible, whereas alternative have maximimum repetition rate of 1-10 kHz.*Very small dark counts (10/second) compared to high dark count (1,000s / second) of alternatives. Does not require gated mode unlike alternatives. Operates in continuous operation mode.
-
Product
GPS NTP Time Server - SYNTIME
-
Signals & Systems India Private Limited
Your product description goes hGPS NTP Time Server (SYNTIME) for Network Time Synchronization is a highly accurate time server. It generates time protocols to synchronize NTP/SNTP clients (Simple Network Time Protocol)/PTP clients (Precision time protocol IEEE 1588) over the network and operates at a speed of 10/100/1000Mbps. The NTP server accepts the time and frequency signals from sources like GPS or GLONASS. It achieves nanosecond accuracy and the system clock operates at stratum 1 when synchronized with time sources. It is a sleek, rack-mountable unit that synchronizes and maintains equipment/device time and avoiding any time drifts due to local RTCs. NTP output from time server supports unicast, broadcast, and multicast methods based on selection and behaves like a reference clock for the network. Apart from time synchronization protocols, it supports MD5 (Security key), SNMP, SSH, HTTP (Configuration), TELNET, FTP, and SYSLOG. IP address of the LAN ports can be field configurable.
-
Product
Dual Channel Driver Card
40461
-
Two channels of 8 to 10 MHz drivers (25 V amplitude). The output voltage range is ±25V, with independent high and low voltage settings. The inputs to the Card are optically isolated. The card also contains voltage and current sense capability, which allows muxing of the current or voltage output measurements from all the Driver Channels in the system to a single DVM. The card allows independent programming of the rise and fall time of each channel as low as one nanosecond increments.
-
Product
Intensified Cameras - Ultra-Sensitive CMOS Cameras from Deep UV to NIR Spectrum
iCameras
-
The cameras are equipped with a high-resolution sensor with high frame rate for excellent quality of image production, which is well‐suited to detect high speed moving objects or ultra-fast phenomenon.The mechanical architecture of the iCamera is small, compact and light-weight, especially designed for easy integration into any system.The iCamera features an exceptional sensitivity based on high QE image intensifier - ultra-fast gating technology down to a few nanoseconds, which allows it to be coupled with a laser source to perform high fidelity active imaging.
-
Product
Switch Filter Bank
-
Corech Microwave’s Switch Filter Bank frequency covers DC to 50GHz, featured with multi-channels (4 to 8 channels), high power handling, and fast switching options. Pin Diode Based Switched Filter Banks provide the highest level of signal isolation, higher operating power levels, and lower insertion loss and achieve switching speeds of < 40 nanoseconds.
-
Product
BCD to Binary Converter
BCD250
-
Computer Conversions Corporation
The BCD Series of BCD to Binary Converters will convert 4 digits of scaled BCD angle data with a full scale of 359.9degrees into 12 Bits of binary angle data (MSB=180degrees). These units are entirely digital, require no timing or control signals and do this conversion in less than 500 nano-seconds. Logic levels are TTL/DTL compatable and +5V DC power is required. They are packaged in a 2.6 x 3.1 x .82" H PC board mounting module.
-
Product
Binary BCD Converters
-
Computer Conversions Corporation
The BCD Series of BCD to Binary Converters will convert 4 digits of scaled BCD angle data with a full scale of 359.9degrees into 12 Bits of binary angle data (MSB=180degrees). These units are entirely digital, require no timing or control signals and do this conversion in less than 500 nano-seconds. Logic levels are TTL/DTL compatable and +5V DC power is required. They are packaged in a 2.6 x 3.1 x .82" H PC board mounting module.
-
Product
Pulse generator
9355-1
-
Solar Model 9355-1 Pulse Generator is designed to provide impulse excitation by means of an injection probe placed around interconnecting cables or power wires. The unit uses a charged transmission line (50 ohms) to generate a pulse with less than 2 nanoseconds rise and fall time, and duration of approximately 30 nS, calibrated in a 50 ohm fixture to deliver up to 5 amperes at a rate of 30 p.p.s. for one minute as required by MIL-STD-461D/E, test method CS115.
-
Product
Pulse Characterization Sensors
-
Pulse Characterization Sensors provide the ability to see and measure the temporal characteristics of pulsed and CW laser beams. Ophir Fast Photodiode Detectors are designed to convert optical signals into electrical signals which are then measured with third-party instrumentation such as oscilloscopes and spectrum analyzers. Accessories are available to connect to IS6 integrating spheres or fiber optic cables. Attenuating filter accessories are also available to increase their dynamic range. Different models offer silicon, UV enhanced silicon and InGaAs PIN photodiodes, covering a combined spectral range of 193 nm to 1700 nm. Rise times range from 25 picoseconds to 3 nanoseconds. The fast rise times are achieved by an internal reverse bias voltage circuit. Power is supplied by internal batteries and/or an external power supply depending on the model. Detectors should be connected to a 50Ω impedance in order to maintain their nominal rise times. They can be connected to higher impedance loads, but this will result in a significant increase in the rise time. If higher output voltage is required, it is recommended to connect the detector to a trans-impedance amplifier with an Input impedance of 50Ω
-
Product
Manage Power, Thermal & Control Planes In Real Time
Platform Manager 2 & L-ASC10
-
*Full fault coverage – monitor all rails and temperature nodes*Manage from 10 to 80 supplies using just the required number of L-ASC10 hardware management expanders*Minimize fault propagation by enabling individual hardware management sub-blocks (power, thermal & control path) to respond to faults in other blocks within nano-seconds*Save CPLD I/O pins by eliminating the need to monitor power-good signals of DC-DC converters*Reliable power & thermal fault detection in hardware, as opposed to software routines
-
Product
GPS Time Synchronization Unit
-
Signals & Systems India Private Limited
GPS Time Server – GPS-DRM-1010 is a compact DIN rail mountable unit that synchronizes and maintains the timing and frequency requirement of power and process industry equipment using a signal obtained from different external sources such as GPS and GLONASS. It provides nanosecond accuracy when external time references are not available. It has a storage facility to store the system log file. It delivers NTP, SNTP, IRIG-B, PFC-Pulse, RS232 & RS485 outputs. The system enables configuration and monitoring through a Web-based application.
-
Product
Pulse & Delay Generators
-
The benchtop pulse generators feature a fast risetime and low jitter. Our most popular digital delay pulse series 575 and 577 generators are now available with selectable time references. With up to eight channels of delay and width control, each individual channel's reference can be set either to the trigger or to any other channel. So look below if you require a picosecond pulse generator or nanosecond pulse generator for your application.
-
Product
Hawk - E Co Processor
9322 E
-
Basic Hawk Co-Processor card set with 2.0 Mbyte memory and microcoded instructions for Nova 4X and Eclipse S280. Executes ALU instructions in 275 nanoseconds. ISA bus compatible, two slots required. Approximate CPU performance of actual S280.
-
Product
Diode Laser Driver
D200
-
The D200 is a compact, DC-coupled fast laser driver, providing up to 4 amps of regulated constant current. A built-in edge-triggered pulse generator produces up to 1 microsecond pulse widths and 2 nanosecond transition times, capable of driving lasers with forward voltages up to 9 volts. A pulse-follower mode is also provided, accommodating externally-defined trigger widths up to 100% duty continuous-wave (CW). Power, pulse width, drive current and differential triggering functions are accessible through a ribbon cable header for embedded OEM applications. A low-inductance laser drive interface permits direct laser connection or custom interposer and flex-cable attachment.
-
Product
SP1T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave manufactures pin diode RF switches that are controlled by TTL logic. This configuration is known as single pole, single throw and is often abbreviated SPST or SP1T. They have been engineered to function in 50-ohm systems, and are designed to operate from 40 MHz to 18 GHz. They have a switching time of 100 nanoseconds and input power rating of 200 mW (23 dBm). Performance of 1.6:1 or better VSWR and minimum isolation of 60 dB is typical of most models.All switches of this type require both +5VDC and -5VDC to operate. Typical current consumption is +/- 30 mA. TTL control logic of 0 to +5VDC is required. Units comes standard with SMA connectors.
-
Product
IRIG B to NTP/SNTP Converter
-
Signals & Systems India Private Limited
IRIG B TO NTP/SNTP CONVERTER – SPC-INS-1010 is a compact DIN rail mountable protocol converter unit which synchronizes and maintains the timing and frequency requirement of power and process industry equipment using IRIG-B signal obtained from GPS receiver. It provides nanosecond accuracy when external time references are not available. It has the storage facility to store the system log file. It delivers NTP, SNTP, PFC-Pulse, RS232 & RS485 outputs. The system enables configuration and monitoring through Web-based application. It supports a wide range of power supply input either 90V-260V AC/DC or 18-36VDC or 36V-72VDC.
-
Product
High Level of Customization at an Affordable Price
TLP
-
The Impulse transmission line pulser (TLP) discharge networks are easily integrated with other instruments for a custom system matched for your device and process applications. Specifications include 1-10 nanosecond rise times, up to 40 amps peak, for 10-500 nanosecond pulse widths. It is a proven design incorporating 15 years of hardware and device development experience. Reliable performance over hundreds of processes, and thousands of products. All TLP systems are built by special request, contact us with your specifications or application.
-
Product
SP2T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave's 2-way switches are available in absorptive and reflective designs from 20 MHz to 18 GHz. They are also referred to as single pole, double throw and abbreviated SPDT or SP2T. These switches have a typical VSWR performance of 1.6:1 or better and input power handling of 200 milliwatts maximum. Switching time is 100 nanoseconds, and isolation of 60 dB or greater for most models. Supply voltages are +5V and -5V, with TTL logic control voltage of 0 to 5 volts.Both absorptive and reflective SPDT switches are packaged into Pulsar Microwave's SW2 outline. Configuration is standard with SMA female connectors. Voltage is applied with wire wrap feed thru terminals. The housing serves as electrical ground, and two turret terminals are installed for wiring.
-
-
Product
Dual Channel Driver Card
42460
-
Two channels of 32 MHz clock drivers with up to 20 volt amplitude. The output voltage range is ±20 V, with independent high and low voltage settings. The inputs to the Card can be optically isolated. The card also contains voltage and current sense capability, which allows muxing of the current or voltage output measurements from all the Driver Channels in the system to a single DVM. The card allows independent programming of the rise and fall time of each channel one nanosecond increments.
-
Product
SPDT PIN Diode Switches
-
Fairview offers a comprehensive selection of 23 different models of SPDT PIN diode switches that cover frequencies ranging from 10 MHz to 67 GHz. The high isolation levels up to 80 dB ensure that unwanted signals will not leak into the desired signal path. Other critical performance features include low insertion loss as low as 1.1 dB and fast switching speed performance as low as 50 nanoseconds. Both absorptive and reflective designs are available and every model utilizes integrated TTL compatible high speed driver logic circuitry. These SPDT switches are constructed using MIL-Grade rugged coaxial packages and several models support field replaceable connectors. All models are EAR99.
-
Product
Intermittent Fault Detection & Isolation System
IFDIS
-
The IFDIS™ uses patented Intermittent Fault Detector technology that simultaneously and continuously monitors every circuit path within a Unit Under Test (UUT) - such as a Line Replaceable Unit (LRU) chassis' interconnects - for intermittent continuity failures that occur for as short as 50 nanoseconds. This state of the art technology is combined with an environmental chamber and vibration table, which simulate the UUT’s operational environment and cause intermittent faults to manifest, creating a system that is unsurpassed in intermittent fault detection.
-
Product
Digital Delay Generators
-
Highland has introduced three unique features to digital delay generation: a "Queued Updates" feature allows time settings to be changed without corrupting ongoing timings; a "Train" feature allows multiple pulses to be generated from each trigger; and a "Frames" feature allows complex delay sweeps and pulse scenarios to be pre-loaded and rapidly executed. Digital delay and pulse generators are available in 1-6 channels, with square, Gaussian, and arbitrary waveshapes, and insertion delays as low as 10 nanoseconds.
