Distribution Amplifiers
amplify each output from input's split.
See Also: Amplifiers, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Video Distribution Amplifiers
-
Product
Shortwave Power Amplifier
OM2501A (OM3501A)
-
The OM Power model OM2501A and OM3501A are designed for all short wave amateur bands from 1.8 to 29.7 MHz (including WARC bands) and all modes. OM2501A is equipped with a FU728F or GU84B ceramic tetrode and OM3501A is with GU78b ceramic tetrode.
-
Product
Class-D Audio Amplifiers
-
Analog Devices is a leader in Class-D audio amplifiers and audio signal processing, and we deliver audiophile-level performance with our proven analog and digital technology. We offer a wide range of audio amplifiers, including industry-leading microphone preamps, microphone drivers, line drivers, and receivers. Our Class-D amplifiers, in particular, are among the lowest power and lowest distortion in the industry. Our portfolio includes Class-A, Class-B, and Class-D audio amplifier offerings, along with a breadth of power ICs. Analog Devices amplifier products have been used in many high volume consumer products where the highest audio quality is expected. The lowest power consumption also enables this performance in many battery powered applications as well.
-
Product
DALI Distribution And Commissioning
UBi
-
Every UBi can create up to 6 branches of a DALI line. Simply put a DALI line into one of the 2-way pluggable terminals, and then use any combination of the 5 remaining terminal pairs to route your cable anyway you like. Or, if you want the UBi to be a power supply, simply power a UBi Power with 24VDC and it will power your DALI line with 21.9VDC 245mA and still give you 5 DALI connections – one for your DALI controller and four to branch however you like.
-
Product
Amplifiers
-
We have designed and manufactured amplifiers using all major semiconductor materials, LDMOS, GaN, GaAs, and InP, to produce narrow, wideband, and pulse, receive and transmit amplifiers from 1 MHz to 220 GHz and power levels from mW to over 10 kW.
-
Product
L-Band Separate Raman Fiber Amplifier
RFA6000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
High-Power Pulsed Amplifiers
-
High power pulsed amplifiers are capable of providing over 1KW of peak power above 10GHz. These SWaP-optimized, high-reliability products have been designed to withstand the toughest environments. For custom requirements, Mercury leverages its proven building-block design approach to rapidly deliver a solid-state power amplifier (SSPA) for your application.
-
Product
GaN Amplifiers
SBP-3233831838-KFKF-E1-HR
-
Model SBP-3233831838-KFKF-E1-HR is a power amplifier with a typical small signal gain of 18 dB and a nominal Psat of +38 dBm across the frequency range of 32 to 38 GHz. The DC power requirement for the amplifier is +30 VDC/2 A. The mechanical configuration is an inline structure with K(F) connector as its input port and output port. Other port configurations, such as K connectors and WR-28 waveguides for either the input or output, are also available under different model numbers.
-
Product
Load Cell DIN Rail Signal Amplifier
LCD20
-
Our intelligent strain gauge bridge amplifier is a compact, stackable microprocessor based unit specifically designed to control and monitor process applications. Flexible connection to most load cells, pressure or strain gauges over a wide range of sensitivities. The unit provides isolated current 4-20mA and voltage 0-10V analogue outputs and two digital inputs. Two set point relays can be configured to set thresholds such as net, gross, peak and valley. Powered from a wide ranging DC supply, the DIN rail amplifier is supplied with 2 part screw connectors for ease of installation.
-
Product
Amplifiers
-
low noise wideband current amplifiers (current to voltage converter) with a high gain and wide frequency band.CA261F2 and CA-461F2 are low noise voltage amplifiers which realize high precision signal processing and high density mounting by using single-in-line package which has six-surface strict shield.
-
Product
Lock-In-Amplifiers
-
Current and voltage inputWorking frequency up to 45 kHzAdjustable sensitivity, time constant and phaseLocal and remote controlCompact and EMI-shielded case
-
Product
DR Range Broadband Power Amplifiers 10 KHZ - 400 MHZ
DR Series
-
Class A solid stateBroadband (instantaneous single band): 10 kHz 400 MHzTypical output power : 60 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 40 W and H<-20 dBc up to 250 MHz andP1dB > 25 W and H<-20 dBc from 250 MHz to 400 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
Product
Small Signal RF/Microwave Power Amplifier
-
R&K’s small signal amplifier series are to amplify various high frequency signals such as CW/Pulsed/AM/FM/N-DCMA/W-CDMA/OFDM , etc.
-
Product
Femtosecond Multipass Ti:sapphire Amplifier
MPA 50
-
MPA 50 is a multipass Ti: sapphire amplifier based on a two-mirror confocal design and containing a pulse stretcher, a pulse compressor, a pulse picker, synchronization electronics, and the Faraday isolator.
-
Product
High Voltage Op Amplifiers ≥12V
-
High supply voltage op amps are used in systems that demand the widest dynamic range with the best signal-to-noise ratio. Engineers turn to Analog Devices for high voltage amplifiers that deliver industry-leading performance. Increasingly, new high voltage amplifiers also offer features to improve system performance, cost, and robustness while easing the complexity of system design. New features include integrated input overvoltage protection (OVP), on-chip electromagnetic interference (EMI) filtering, higher electrostatic discharge (ESD) immunity, and greater resistance to latch-up in both powered and unpowered operations.
-
Product
Slim & High-Performance Charge Amplifier
6001-A, 6002-A
-
Measuring a wide variety of vibration: automotive, rail transportation equipment vibration, motor/pump vibration, vibration response during vibration test. Also available for a vibration test device for calibration of equipment.
-
Product
Gain Shape Linearizer Amplifiers
-
Gain Shape amplifiers are used in a number of applications where it's necessary to flatten the gain characteristic of the preceding or following component. This would include flattening the attenuation of a long cable run or perhaps changing the input gain response to a MPM (Microwave Power Module) or TWT (Traveling Wave Tube) to compensate for the gain variation within the tube.
-
Product
LT Range Broadband Power Amplifiers 20 MHZ - 1000 MHZ
LT Series
-
Class A solid stateBroadband (instantaneous single band): 20 MHz 1000 MHzTypical output power : 90 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 60 W and H < -20 dBc from 20 MHz to 80 MHz andP1dB > 75 W and H < -20 dBc from 80 MHz to 500 MHz andP1dB > 45 W and H < -20 dBc from 500 MHz to 1000 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageUpgradable to LT 160 possibleReliable, efficient and robust19" Rack3 years standard warranty
-
Product
High-Voltage Amplifiers
-
Power amplifiers are a must in applications requiring both complex signals as well as high voltage throughput. However, this is uncommon in high performance instrumentation, therefore an external amplification device must be used. In these cases, a high voltage amplifier is used to increase the size of a signal by some factor.
-
Product
High Voltage Amplifier
WMA-100A
-
The WMA-100A model is our cost-effective, compact, general purpose high voltage amplifier. With its high quality and small form factor, it is the ideal choice for any experiment that requires an all-round, reliable high voltage amplifier. It can also be used as a stand-alone low noise high voltage power supply. Two WMA-100A amplifiers and a WMA-IB-HS phase inverter - buffer can be used to double the output voltage.
-
Product
10mA One-Channel Amplifiers
-
USB connected devices have become common in lab environments. The nano box USB is a standalone piezo amplifier with 16 bit D/A resolution. Its small size and powerful amplifier includes a USB 2.0 interface that offers a variety of helpful commands.
-
Product
Microwave Power Amplifier 1/4 Watt, 10 MHz to 40 GHz
GT-1040A
-
The Spanawave/Giga-tronics GT-1040A Microwave Power Amplifier incorporates broadband MMIC-based architecture. These state-of-the-art amplifiers are based on solid-state parallel MMIC design with exceptionally wide bandwidth and high power. The unique circuit topology is highly reliable, with performance that excels where extremes of bandwidth and power are demanded.
-
Product
Dual Channel HV Amplifier with Phase Inverter
A800DI
-
This unit contains two independent A800 amplifiers that share common ground reference and power supply. Please see A800 page for technical details.It features also a low voltage phase inverter that inverts the signal applied to the input of channel 1. The resulting signal can then be connected to the input of channel 2 by means of a short BNC cable (supplied). As a result the two outputs operate in counter-phase.
-
Product
QuickLink Solder-In Starter Pack for use with Dx10 Amplifier
Dx10-QL-3SI
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Video Distribution Systems
VDU-100 Series
-
Systems Engineering & Management Company
SEMCO'S tactical military products have been developed in response to the requirement for near real-time, high-quality, encrypted video and sensor data capture, transmission and distribution in support of covert and overt military operations. These products provide for unprecedented audio-video and data communications from warrior-to-warrior as well as from warrior-to-command. Transmission modes include tactical and handheld radios, wireless and wired LAN, SATCOM, wireless Mesh, and Cellular, with full motion video capability in as low as 125 Kbps bandwidth. Video resolution, bandwidth and frame rates are adjustable, with high quality video frames capable of being transmitted in bandwidths as low as 9 Kbps. These products include video recording, with both local and remote download capability, as well as remote video enhancement, pan, tilt and zoom control, and multiple NTSC/PAL camera and imaging device interfaces. With administrative and password control, these products provide for unlimited remote viewing on PCs, Androids, iPhones and iPads anywhere in the world.
-
Product
Panel-mounted Amplifier(Power System Simulation )
PA30Bi-H
-
PA30Bi-H is the panel-mounted type power amplifier model which can produce 3-phase current, with maximum RMS phase current of 30A and maximum output power of 450VA, and 4-phase voltage, with maximum RMS phase voltage of 250V and maximum output power of 75VA.
-
Product
Distribution Transformer Tester
DOC-2000™
-
The DOC-2000™ is a test instrument designed for distribution networks transformers up to 167KVA. It can determine the presence of short circuits or an open circuit in the distribution transformer primary winding & also short circuits on the secondary winding. The DOC-2000™ is designed to be operated from an arial device or from the ground at the end of a hot stick without disconnecting the transformer’s secondary windings.
-
Product
Linear Amplifiers
-
Macom Technology Solutions Holdings Inc.
MACOMs linear amplifiers offer high IP3, power up to 2.5 W and are offered in a variety of DIE and package types to simplify point-to-point wireless, SATCOM/VSAT, and radar system design.
-
Product
Galvanic Isolation Amplifier
X005 Series
-
The X005 Galvanic Isolation Amplifier provides a regulated and resistively limited +5V dc power supply required by the sensors, it can be connected in three or five wire modes. Used in five wire mode positive and negative sense inputs enable the X005 to dynamically adjust the sensor supply thus ensuring the correct voltage across the sensor. Connected in this way the X005 can compensate for 15 conductor resistance. The sense terminals are linked internally so the end user can use the X005 in three wire or five wire mode without the need to fit or remove external links.
-
Product
FTTx PON Optical Amplifier (1540~1563nm)
HA5800B (2RU)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5800B (2RU) series is a low noise, high performance, FTTP high power, multi-ports optical amplifier with gain spectrum band within 1540~1563nm. Each output port for optical amplifier has built-in well-performed CWDM. Every external up-link optical port of optical amplifier can connect with OLT PON port very conveniently. Each 1550nm (CATV)'s output optical port multiplex 1310/1490n's data stream, in order to reduce the quantity of the component and improve the index and reliability of the system.
-
Product
High-end Cable DAC & Amplifier
Impacto essential
-
Beyerdynamic Digitalize high-end headphones.
