Organic LED
Light Emitting Diode with emissive electroluminescent layer composed of organic compounds.
-
Product
Multi-Wavelength Foresnic LED Light Source
HandScope LED
-
The only LED unit that changes and selects wavelengths like a forensic light source.
-
Product
Goniophotometer Test System For Led Lamp
LCG-1680B
-
Shenzhen Chuangxin Instruments Co., Ltd.
Design according to IEC61341the test method of central luminous intensity and beam angle for reflecting light, this instrument can be used to test the cross section luminous intensity distribution curve, central luminous intensity and effective beam angle of LED assembled luminaries and LED lens system with diameter less than 180mm.
-
Product
LED light sources
MLED4
-
Photocatalysis, ultraviolet analyzer biological genetic engineering, molecular genetics, medical and health, biological products, pharmaceutical research, health and epidemic prevention, dye chemical industry, petroleum chemical industry, textile industry, etc.
-
-
Product
LED Test Programmable DC Electronic Load
IT8912E Series
-
IT8900 series high accuracy LED specific testing electronic loads can simulate the real output of LED lights with different characteristics.Their specific circuit can realize CR-LED mode, adjustable frequency, duty ratio PWM dimming output port (frequency: 20Hz-2KHz), I-pp/I-max measurement function can test current ripple and start up surge current of LED constant flow source. Voltage and current testing speed can reach 50KHz. IT8900 series provides CR-LED / CC / CV + CC / CR /CW and other working modes, built-in USB / RS232 / GPIB communication interface. Widely used in LED driver power dimming test.
-
Product
Modular DC Electronic Load LED Simulator
6310/A
-
Chroma Systems Solutions, Inc.
Chroma 6310A Programmable Electronic Load integrates microprocessor capabilities into each load module and mainframe to provide simple and accurate parallel operation to optimize the speed and control among multiple load modules. All load modules may be configured to work synchronously, to test multiple outputs simultaneously, thus simulating real life applications.
-
-
Product
SparkFun LED Driver Breakout
TLC5940 (16 Channel)
-
The TLC5940 is a 16 channel PWM unit with 12-bit duty cycle control (0-4095), 6 bit current limit control (0-63), and a daisy chainable serial interface. This breakout board is a good way to take full advantage of this useful IC. All 16 PWM channels are broken out to standard 0.1" headers, which run alongside convenient voltage and ground rails. Also, because the TLC5940 can be daisy-chained, the breakout is designed to support that feature. On the left-hand side of the board all serial inputs are broken out to 0.1" headers and likewise with output on the right-hand side.
-
-
Product
Organic Elemental Analysis
-
Elementar Analysensysteme GmbH
Carbon, hydrogen, nitrogen, oxygen and sulfur are the basic elements of living nature. Their quantitative determination in the most versatile combinations of substances, the elemental analysis, is the origin and essence of the Elementar product portfolio.
-
Product
Organic Pollutant Monitor
OPSA-150
-
The OPSA-150 is a organic pollutant monitor that uses HORIBA's proprietary Rotary Cell Length Modulation, a measuring technique incorporating 25 years of expertise. The unit can be used as an organic pollutant monitor at drainage systems for determining compliance with COD monitoring regulations, for monitoring quality of water measuring levels of organic matter at water supply intakes, and as an organic monitor on process lines (phenol meter).*Pole mount, outdoor cover, and analysis panel are available as options.
-
Product
LED Power Driver ATS
8491
-
1. DC Electronic Load : Chroma 6310A/6330A Series2. Transducer Unit/Module*1 : Chroma A849101/A849102, A849103, A8491043. Time/Noise Analyzer : Chroma 80611 & 80611N card4. Sytem Controller*2 : Industrial PC5. DC Source: Chroma 62000P Series6. Digital Power Meter : Chroma 66200 Series7. OVP/Short Circuit Tester : Chroma 806128. ON/OFF Controller : Chroma 80613*1 : A849101 transfers UUT output signal to voltage signal, and measure by 84911 LED power driver measurement card (200kHz). The optional 80611N Noise card is required for 20MHz ripplecurrent measurement.*2 : The controller includes both 84911 LED Power Driver measurement card and 84903 control card.- 84911: Measure rms current, dimming current/frequency/duty, timing, power & ripple current (200kHz)- 84903 : Provide BL control signal(DC level, PWM, SM bus), and enable ON/OFF signal.C Source : Chroma 6500/61500/61600 Series
-
Product
LED LIGHT DISTRIBUTION TESTER
-
Essential elements among LED inspection categories are the light quality and intensity. Accurate measuring for optical characteristic requires diverse photo-measurement technology which fits into production lines. This system extracts conditions necessary for optical measuring optical characteristics on production equipment through accurate measurement both of the quality and of intensity of LED light distribution characteristics.
-
Product
LED Driver Aging Rack
LEDRACK-100W192P
-
• Application range: LED driver and multi channel driver power aging. It has equipped with computer operation and monitor system. The working condition can be set by the computer, and the computer will record real time data to do statistical analysis. • The parameters of load can be set freely on the software, to monitor the real time voltage, current, and power etc • Load mode: CC, CV, CR, CP, and LED • Aging Control System includes: ON/OFF control signal output; Signal of relay switch control; K type thermocouple temperature acquisition • The channels are parallel connected under arbitrary load mode, which can allow product power expansion • The LED Driver Aging rack will design according to customer’s LED driver power and aging quantity per time • Automatic current switching function (optional) • AC power meter to measure modules, and test power input characteristics (optional) • Temperature monitoring function at product zone (optional) • PWM dimming and two sets of logic control signal function (optional)
-
Product
LT-300A Aging-Life Test System For LED Luminaires
-
Hangzhou Everfine Photo-E-Info Co., LTD
LT-300A system is widely used for normal /accelerated aging, lumen maintenance measuring, chromaticity shift measuring, lifetime evaluation and temperature characteristic testing for LED luminaires, arrays, and modules. The extrapolation of lifetime by programmable models is also available to estimate the lifetime of LED luminaires.
-
Product
Fuorescence LED Illumination System
pE-2
-
The pE-2 is a fluorescence LED illumination system which provides repeatable and controllable light with a choice of 20 different LED peaks. It is perfect for the researcher who has a specific set of tests to conduct. The user can specify a wavelength configuration matched to their particular fluorescence requirements. It is modular, allowing LED wavelengths to be exchanged as requirements vary or additional experiments are added. Manual control is via a remote control pod with instant on/off and intensity control from 0-100%. Additionally, the system is fully integrated under many imaging software packages.
-
Product
LED tester
-
Ecopia's LED tester is good to measure both electrical(I-V curve) and optical(Spectra, Light intensity) properties of LED chip, LED lamp, SMD type at the same time.It also makes it possible to see LED sample's construction , seeing through microscope. LED tester main body flow input current ,and emitted light from the LED sample is focused on lens of microscope.From this process, our LED tester can provide repeatable tested results and minimize error values and improve convenience of how to use.
-
Product
Non-Contact Voltage Tester w/ LED Flashlight
LVD1A
-
Non-contact AC voltage detector and LED flashlight combined in one convenient, compact design. With exclusive dual-sensitivity. The voltage detector glows blue when it's near AC voltage, and glows red when it's at the source.
-
Product
LED CIRCUIT TESTER, 6-12V AND 24V
MD1646
-
Checks high and low voltages on 6-12V and 24V circuits. Connect the red lead to a power source and the black lead to a ground source. Tester will light up red for power and green for ground during testing.
-
Product
SMD LED Aging Test Machine
CX-6100
-
Shenzhen Chuangxin Instruments Co., Ltd.
Designed to measure the aging-life and color comparisons of 50pcs 5050 SMD LED and 100pcs 3528 SMD LED.• 150 separate constant current supply• Aging functions: constant current, impact pulse, on-off mode• Range of forward voltage(VF): 5.0V• Range of forward current(IF):1) constant current: 0-100.0mA2) Impact pulse: 0-200.0mA• Range of impact pulse frequency: 10-9999Hz; Duty ratio: 1%-99%
-
Product
LED Light Measurement System
-
RayClouds Photoelectric Technology Co.,Ltd.
The LED optical measurement system includes Blue Light Analyzer, Glare Analyzer, LED Light Intensity Measurement, LED Goniophotometer, Lighting Electrical Measurement System, LED LightBar Measurement System, LED Photochromic Tester.
-
Product
Power Meter and LED Source
PM23 and LS20DV
-
The PM23 and LS20DV power meter and LED source are top of the range units for multimode testing of multimode libre links. The PM23 power meter is also calibrated as standard at 1550nm making it suitable for measuring singlemode links when used in conjunction with a suitable source. The LS23DV has 850nm and 1300nm switchable outputs from 1 port and a visible tracer from the other.
-
Product
SMD LED Aging Tester
-
Shenzhen Chuangxin Instruments Co., Ltd.
LED life tester with 150 independent constant current to aging-life and color comparisons of 50pcs 5050 SMD LED and 100pcs 3528 SMD LED.
-
Product
LED Luminous Intensity Distribution Tester
LS860
-
LS860 Luminous Intensity Distribution Tester is a precise electronic instrument for measuring LED luminous intensity. It’s strictly designed according to LED standard requirements of CIE 127-1997 A or B Condition.
-
Product
LED Optical Aging Test Instrument
LEDLM-80PL
-
LEDLM-80PL LED Lumen Maintenance and Aging Life Test System is designed according to standards of IES-LM-80, IES-LM-82, TM-21 and GB2312-80, and the software is developed base on Arrhenius model. LED has the features of long life, but with the different working condition and drive current, its life will be different, but generally the life will be around 50K hours. Differ from the traditional lightsource, LED light will decay gradually rather than extinguish instantly, so in the standard of LM-80, it introduces L70, L50 and etc.
-
Product
Light Meters For LEDs
-
Photometers for the measurement of visible LEDs and radiometers for UV , visible and NIR LEDs.
-
Product
6-24V Multi-functional Auto Tester With LED Display
6510A
-
Peaceful Thriving Enterprise Co Ltd
Test the automotive electrical system within 6-24V. In order to save the testing hours for the automotive electrical system, the tester is designed to test the system without re-connection between the vehicle battery and the testing components. For the testing and safety purpose, the tester contains short-circuit protection, which can also check the ground connection without voltage drop test. The short-circuit protection system contains the recoverable fuse, so the technician will not waste the fuses during the testing. The extension cable is long enough for a technician to test the whole system for the vehicle. Therefore, the technicians do not have to search for ground connection constantly.
-
Product
LED Drivers led Switching Power Supply
-
Dongguan Longwei Electronic Technology Co., Ltd.
LED drivers led switching power supply
-
Product
Total Organic Carbon
-
Teledyne LABS’ brand of Total Organic Carbon (TOC) analyzers provide unparalleled accuracy, precision, throughput and robust construction for water samples varying in quality from semiconductor-grade to municipal wastewater. All our pharmaceutical instruments have available 21 CFR Part 11 software tools for your compliance needs, as well as validation documentation, services and training.
-
Product
Instrument Systems LED And Display Measurement
-
Konica Minolta Sensing Americas, Inc
Instrument Systems is a frontrunner in developing state-of-the-art light measurement equipment, software, and accessories, taking great pride in constructing products that provide fast, accurate readings to ensure precise data for laboratory, production and quality assurance testing. All Instrument Systems products have stringent quality and performance requirements to ensure that customers get the highest quality equipment. As a leading supplier world-wide, they provide cost-sensitive support to a diverse clientele to help them measure luminance, flux, intensity, illuminance, and chromaticity of LEDS, lamps and displays throughout all aspects of product development and production.
