-
Product
JFET Input Amplifiers
-
Analog Devices JFET input op amps or FastFET high speed (>50 MHz) input op amps provide high input impedance and ultralow input bias currents for high speed applications. The majority of our FET input op amps feature wide supply ranges from +5 V to 12 V or higher and feature rail-to-rail outputs enabling wide dynamic range.
-
Product
Wideband GaN Amplifiers
-
The Teledyne RF & Microwave family of GaN-based amplifiers maximizes power density and efficiency, and establishes a new benchmark for small size in the 0.1 to 6.0 GHz range that operates over multi octave. With dimensions of 2.5"L x 2"W x 0.42"H at only 2.1 cubic inches, these modular, non-ITAR GaN amplifiers maintain the rugged design characteristics needed for harsh airborne and land based requirements.
-
Product
Erbium Doped Fiber Amplifier
EDFA
-
Optoplex designed and produced high power single-mode and polarization-maintaining EDFA, which met MSA compatible requirements. C-band MSA EDFA Module with +23 dBm Output Power is Optoplex standard product. Optoplex designed Pre-EDFA provides more than 35dB gain with -40dBm input power. The Double-Cladding pumped EDFA produces 2W output power.
-
Product
Wideband Power Amplifiers
-
Krohn-Hite Wideband Power Amplifiers are designed to meet today's industrial needs where wideband, precision performance is required. Applications include: meter calibration, piezo transducer driving, bridging applications requiring high input and low output impedance, low distortion ac power source, ion beam deflection, vacuum tube driver, ink jet testing and design and many more.
-
Product
DC-Coupled Pulse Amplifiers
-
These DC-coupled pulse amplifiers are available in a simple DC-power module format, and are also available in an AC-powered benchtop instrument format. All models will drive a 50 Ohm load.
-
Product
Power Operational Amplifiers
-
ST offers a portfolio of power op-amps characterized for high output current, low drop and high gain. This makes them suitable for a wide range of applications and, in particular, for driving inductive loads such as motors and lamps, as well as in automotive applications offering superior performances. Our op-amps are available in insertion and surface-mount packages to meet different environmental requirements.
-
Product
Transconductance & Transimpedance Amplifiers
-
Measurements International Ltd.
0 to 100 Amps – AC, 0 to ± 100 Amps – DC, Voltage Compliance ± 5 Volts, IEEE-488 Interface, Resistive, Capacitive, Inductive Loads.
-
Product
Low-PIM, High-Power Filter Solutions for Monitoring Broadband Emissions
-
Enables monitoring of PIM to 13 GHz; 100W CW and 1KW peakNear-end monitoring: Carriers rejected -90dB by the notchtravel through the bandpass filter to the low PIM termination.Far-end monitoring: Carriers rejected -90dB by the highpass,IM products passed are monitored by the spectrum analyzer.
-
Product
Millimeter-Wave Amplifiers
-
When your application requires operating at Ka-band and above, trust Mercury Systems’ millimeter wave amplifiers to perform. With standard designs up to 65GHz and custom products available, Mercury is ready to support your high frequency requirement.
-
Product
Pulsed Fiber Amplifier
MOPA
-
These light sources are compact Master Oscillator - Power Amplifier (MOPA) structures that can be directly modulated in a defined operating range of repetition frequency and pulse power. The standard products operate in the wavelength range around 1.5 µm at a repetition frequency > 6 kHz and a pulse energy of 10 µJ/50 ns (200 W peak power).
-
Product
Very Broadband Seismometer
KS-54000/KS-1
-
Geotech's Model KS-54000 is a borehole, Model KS-1 a vault, three-component seismometer, designed for ultra low-noise monitoring for frequencies from 0.003 to 5 Hz, being below the Low Noise Model for frequencies up to 5 Hz.
-
Product
High Power Amplifiers
-
Solid State Power Amplifier (SSPA) technology continues to offer opportunities to displace Travelling Wave Tube Amplifiers (TWTA) from radar, communication and Electronic Warfare (EW) applications.
-
Product
High-Power CW Amplifiers
-
Our family of solid-state power amplifiers (SSPAs) utilizes proprietary technology and a proven building block approach that enables rapid customization to specific requirements. The world-class design team understands the tradeoffs between GaAs versus GaN and FET versus MMIC to quickly achieve the right design for the right problem. Whether you need a connectorized compact GaN SSPA or an integrated SSPA assembly, we have the technical know-how to deliver on-time and on-budget.
-
Product
High-end Cable DAC & Amplifier
Impacto essential
-
Beyerdynamic Digitalize high-end headphones.
-
Product
Five Channel Amplifier
-
Teledyne RF & Micrrowave designed the Five Channel Amplifier specifically for a custom space application. Each independent channel used dedicated RF Input/Output and DC bias connections. Each channel's RF performance was tailored differently to meet the application requirements. All components were manufactured and screened per MIL-PRF-38534, Class K. Additionally, to meet mission requirements The top assembly was also tested for RF and DC parameters during MIL-STD-202 thermal cycling and random vibration environments. This effort required disciplined development, manufacturing and program management efforts to meet challenging mechanical and RF engineering requirements.
-
Product
GPS Filter Amplifiers
-
Mercury Systems’ family of GPS filters/amplifiers is the right choice for your high reliability GPS receiver. Whether your application is ground, airborne, missile or launch/reentry vehicle, you can trust the technology behind these advanced products. Custom designs including multiple outputs and integrated receiver protection limiters are also available.
-
Product
Low Noise Amplifiers
-
Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a variety of applications but are primarily suited to airborne, maritime and ground based radar systems. LNAs are primarily intended to minimise added noise whilst providing high gain so design focusses on the parameters associated with the noise response of the amplifier. They are usually the first amplifier in the Radar detection chain and will have the lowest noise figure.
-
Product
Bench-Top Type Amplifiers
-
– A variety of wavelength bands– Most models have the RS232C / IEEE488.2(GP-IB) interface as default– customization is available– Development of next-generation optical communication systems– Amplification for evaluation of transmitted signals– Detection of faint signals in optical measurements & sensors
-
Product
Combustible Trip Amplifier Module
TA102A
-
The TA102A is a single-channel Combustible Gas Trip Amplifier Module designed for use with one General Monitors intelligent transmitter to monitor combustible gases and vapors within the lower explosive limit (LEL) and provide status indication and alarm outputs. Microprocessor-based electronics allow all options to be user selectable through a front panel interface (mode / select switch and digital display).
-
Product
Low Noise Amplifiers
WA Series
-
WA series low noise amplifiers are the balance type LNA with alarm capability in some of the products. Besides offering very low noise figure and wide bandwidth, the LNA have high linearity with unconditional stable design. The noise figures are from 0.40 dB to 1.0 dB and IP3 from 30 dBm to 40 dBm.The amplifiers cover the frequency bands of VHF, UHF, Cellular, GSM, DCS, PCS, 3G, C, and wireless LAN. The built-in alarm capabilities include Branch 1 and Branch 2 alarms, Soft Failure alarm, Hard Failure alarm, Soft alarm Open-Collector, and Hard alarm Open-Collector.
-
Product
High Voltage Amplifier
HA-405
-
* 400Vp-p(±200V DC)* 400mAp-p(±200mA DC)* Bandwidth: ≦1MHz(200Vp-p) *Slew Rate: 500V/us *Gain(AMPL):0~90(10 Turn VR) *DC Offset: ≦0~±200V(10 Turn VR+SW) *Output Resistor: 50Ω *Microprocess Control Protection
-
Product
Four Quadrant Power Amplifier
PAV3000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
Low-Noise Amplifiers
-
Broadband, narrowband, high-frequency, our extensive portfolio of LNAs is ready to tackle the toughest requirements. Don’t see exactly what you need? We have a vast library of pre-engineered building blocks ready to support any custom design.
-
Product
Broadband Calibrated Noise Sources
-
Fairview Microwave’s calibrated noise sources cover frequency bands from 10 KHz to 18 GHz. Their performance specifications include output ENR levels ranging from 15 dB to 30 dB and typical VSWR levels as low as 1.25:1. Depending on the model, calibrated frequency points are at 10 MHz, 100 MHz, 1000 MHz, 2000 MHz and 1 GHz steps. The temperature coefficient of these noise sources is < 0.01 dB/°C and noise output variation is < 0.1 dB/%V.
-
Product
Single-Ended Amplifiers
Op-Amp
-
For designs requiring single-ended amplifiers (op amps), Analog Devices' portfolio of high speed op amps and precision op amps provides a broad choice of products that deliver unmatched performance. Explore op amps by parameters, and find expert system-level advice on design problems with our amplifier reference designs (Circuits from the Lab®), design tools, selection guides, calculators, and SPICE models.
-
Product
Broadband Power Amplifier
PAS-00260-10
-
* Solid State Power Amplifier* Gain : 49 dB typ.* High IP3, 50.0 dBm typ.* Bench Top Case* Internal Cooling Fans* Type N Connectors
-
Product
3-Ch Sensor Amplifier
PS-1300
-
The PS-1300 3-Ch Sensor Amplifier is designed to be compact and light weight, and able to be used in combination with a tri-axial accelerometer. Each channel can also be used independently and connected with a single axis accelerometer. The PS-1300 has built-in integration function and enables to optimize the input signal to vibration data analysis devices connected.
-
Product
Amplifiers & Buffers
-
Renesas amplifiers are among the industry's highest-performance, highest-value amplifier ICs on the market. Our broad operational amplifier (op amp) portfolio provides for a wide range of next-gen precision instrumentation, medical, communication and industrial process control applications where innovation, reliability and dependability is central to the analog designs.
-
Product
Distribution Amplifier
-
Also referred to as a splitter, the distribution amplifier sends one computer, video, or audio signal to multiple devices while maintaining signal integrity.
-
Product
40mA One-Channel Amplifiers
-
Piezo amplifiers/controllers are designed for high precision low to mid-speed positioning of low-voltage piezo actuators. These amplifiers are tuned for extremely high output stability and extremely low signal noise at the output. A low amplifier signal-to-noise ratio is very important because it determines the total resolution of the actuator. The nearly unlimited resolution of piezo-electric actuators using these amplifiers results in ultra-precise movement.
