Electron
-
Product
Thermometer
S0842
-
Thermometer is designed for record of temperature. Values are stored to a non volatile electronic memory. Data transfer to the personal computer for further analysis is performed via USB, RS232, GSM or Ethernet interface by means of a proper adapter.
-
Product
Custom Solutions
SYSTEM 8 Custom
-
ABI Electronics offers a range of solutions to cover the most common test combinations. Including both analogue and digital test techniques, they provide an excellent starter package for a wide range of applications. Note that any combination of SYSTEM 8 modules is possible - do not hesitate to contact a member of the sales team to discuss your requirements.
-
Product
Networking Solutions
Bluetooth Solutions
-
Quickly introduce Bluetooth connectivity into sports and fitness, consumer electronics, beacons and smart home applications with easy-to-use and innovative Bluetooth SoCs, modules and software from Silicon Labs.
-
Product
Full System Simulator
Simics
-
Wind River Simics is a full system simulator used by software developers to simulate any target hardware from a single processor to large, complex, and connected electronic systems. This simulation enables the target software (board support package, firmware, real-time operating system, middleware, and application) to run on a virtual platform the same way it does on the physical hardware.
-
Product
PXI 12-Slot BRIC Matrix, 378x12 1-Pole (9 sub-cards)
40-558-121-378X12
Matrix Switch Module
The 40-558-121-378x12 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
High Voltage Differential Probes
-
High voltage differential probes provide high CMRR over a broad frequency range (up to 400 MHz) to simplify the measurement challenges found in noisy, high common-mode power electronics environments. The probe’s design is easy-to-use and enables safe, precise high voltage floating measurements.
-
Product
Alignment Sensors and Switches
-
The Touchswitch is an electro-mechanical limit switch with no moving parts, which detects tracking and misalignment problems on bucket elevators and conveyors. When a belt misaligns or a pulley moves over and contacts the sensor, the built in solid-state electronic circuitry detects the lateral force of the belt or pulley and activates a voltage free relay contact. This relay contact is used to immediately alarm and shutdown the machine.
-
Product
Electronic Product Testers
-
Infinity Machine International Inc.
Electronic Product Testers by Infinity Machine International Inc. - for applications such as connectors insert and extract testing machine, touch screen torsion, abrupt pull tester for power wire and headphone cable, double station electronic product cable tester, cord flexing rotary bending fatigue tester, button click electronic product tester simulation, and more.
-
Product
Digital Flux Meters
-
Digital Fluxmeter is instrument made by electronic integration principle and displays the magnetic flux digitally. It can test magnetic materials. It not only measures flux but also directly tests magnetic performance for the purpose of quality control. With the features of legible display and convenient operation, it is an ideal device for flux measurement.
-
Product
8-Slot BRIC, 252x12, 1 Pole, PXI Matrix (6 Sub-cards)
40-559-801-252x12
Matrix Switch Module
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
Design & Test Software
-
Industry-Leading Design, Emulation, and Test Software.Harness the power of digital twins, artificial intelligence, and automation to streamline workflows, break down silos, and accelerate test cycles.Find out why so many innovators trust Keysight to build their next breakthrough. With software spanning electronic design automation (EDA), instrument control, emulators, IT operations, and application delivery, your next project's only limitation is what you dare to dream.
-
Product
WIFI
-
A compact electronic component that enables devices to send and receive data wirelessly over a Wi-Fi network.
-
Product
Atomic Resolution Analytical Electron Microscope
NeoARM JEM-ARM200F
-
"NEOARM" comes with JEOL’s unique cold field emission gun (Cold-FEG) and a new Cs corrector (ASCOR) that compensates for higher order aberrations. The combination of a Cold-FEG and ASCOR enables atomic-resolution imaging at not only 200 kV accelerating voltage, but also a low voltage of 30 kV."NEOARM" is also equipped with an automated aberration correction system that incorporates JEOL’s new aberration correction algorithm for automatic fast and precise aberration correction. This system enables higher-throughput atomic-resolution imaging even at low accelerating voltages. Furthermore, a new STEM detector that provides enhanced contrast of light elements is incorporated as a standard unit.
-
Product
Electronic Resistance Store
MEMS2-4L
-
The mezzanine serves as an electronic store of resistance to direct current, the value of which is set by software, through two isolated channels.
-
Product
16-Channel VME Analog Output/Thermocouple Simulator Module
V470
-
The V470 is a 6U VME module that provides sixteen independent, isolated analog outputs that may be user-programmed to operate as voltage outputs or thermocouple simulators. Users may write temperature or voltage values at VMEbus speed, and the microprocessor will transparently do all necessary calculations and update the channel electronics.
-
Product
5U centrifugal blower
CB-360A
-
5U centrifugal 330 cfm blower for pressurizing consoles, computers and electronic systems with cool, filtered air.
-
Product
Electrical Safety Test Equipment
-
Making a product “safe” requires an understanding of “hazards” that exist in each electrical product. Electrical shock is one of the four fundamental hazards. Because of that, it must be a part of any product electrical safety evaluation. Even though a product requires an electrical power source and uses electrical or electronic components, it should not present an electrical shock hazard to the user.Ground bond or earth continuity testing prevents electrical shock hazards. Similarly to a fault to earth, test instruments generate a high current. The standard requires that the resistance between protective earth and any conductive surface on the equipment does not exceed 0,1 Ohm. The test is performed by applying a DC current between the conductive surface and protective earth. By measuring the voltage drop, it calculates the resistance.RMO-E instruments are ideal for testing the protective bonding (grounding) of equipment following the standard IEC 61010-1. Applying current up to the value of 100 A and the ability to provide in the Contin menu (continuous operation) test current for the pre-set test duration (equal or exceeding 1 min) gives a user a possibility to easily check the protective bonding/grounding of the equipment. The full load voltage of 12 V assures proper measurement and accurate result. Finally, an instrument displays pass/fail classification according to user-preset parameters.
-
Product
Semiconductor Device Parameter Analyzer and Measurement Modules
B1500A Series
-
Keysight B1500A Semiconductor Device Analyzer of Precision Current-Voltage Analyzer Series is an all in one analyzer supporting IV, CV, pulse/dynamic IV and more, which is designed for all-round characterization from basic to cutting-edge applications. It provides a wide range of measurement capabilities to cover the electrical characterization and evaluation of devices, materials, semiconductors, active/passive components, or virtually any other type of electronic device with uncompromised measurement reliability and efficiency. In addition, the B1500A’s modular architecture with ten available slots allows you to add or upgrade measurement modules if your measurement needs change over time.
-
Product
PXI Digital IO
-
The Keysight M9187A Digital I/O provide static digital input and output channels which can be used in applications that require the monitoring of digital states and the controlling of external devices. These are typically used in aerospace/defense, automotive, and electronic test applications. The module offers configuration flexibility with programmable input thresholds and flexible output drive capability.
-
Product
Volkswagen Oxygen Sensor
KS60113 - Volkswagen
-
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
Product
Ambient Light Sensors
-
The Ambient Light Sensor (ALS) products from ams provide measurements of ambient light intensity which match the human eye’s response to light under a variety of lighting conditions. Each device has a specific operating range of performance, from very low light up to bright sunlight. High sensitivity coupled with wide dynamic range make these ALS products ideal for operation behind dark inked glass. They enable consumer electronics device manufacturers to implement display dimming and brightness control functions, helping to reduce power consumption and extend battery run-time.
-
Product
Cable Harness EM Solver
MHARNESS
-
Electro Magnetic Applications, Inc.
MHARNESS to Complete the Last Mile of EM Coupling Simulation Traditionally, electromagnetic effects simulation has focused on the transients induced on the overall cable bundle of complex systems. MHARNESS is a transmission line solver that reveals the EM transients on the most critical element of systems: the pin interface to electronics systems. Now, EMA3D and MHARNESS can co-simulate in one self-consistent simulation.
-
Product
Single Space Electro-hydraulic Servo Universal Testing Machine
WAW-F Series
-
Jinan Testing Equipment IE Corporation
WAW-F series single space Servo-Hydraulic Testing System Computerized is suitable for testing tension, compression and other strengths of various metallic or nonmetallic materials with high strength. The ultra-large testing space & dual-action actuator with longer stroke enable it to test not only standard specimen, but also longer ones with long elongation every so often. Equipped with the electronics, computer &software packages, it is capable of controlling the test procedures by the predetermined programs. The Servo-Hydraulic Testing System Computerized can also display, record, process and print the test results. The test curves can be drawn automatically in real time. The Servo-Hydraulic Tester of Single Space is easy to operate and is versatile in the applications of metallurgy manufacturers such as steel mills & alloy, reinforced bar, aircraft industry, research institutes, laboratories, calibration institutes etc.
-
Product
Digital Image Correlation System for Complete 3D Warpage, Thermal Expansion, and Strain Analysis of Materials and Components in the Heating and Cooling Phase
Q-400 TCT
-
The Q-400 TCT system is designed for complete three-dimensional and highly sensitive warpage, thermal expansion measurement and strain analysis of materials and components in the heating and cooling phase. Areas from 50 mm x 70 mm down to 2 mm x 3 mm can be investigated. Measurements can be done from room temperature up to 300°C and down to -40°C. The system is specially suited for thermal expansion measurement of electronic components and is frequently used in the development and testing of complex anisotropic materials, components, and structures in electronic applications.
-
Product
Simulation Systems
System
Bloomy offers Simulation Systems for Hardware in-the-Loop (HIL) and open loop test of electronic controls and mechanical actuators for all types of transportation and defense systems including aircraft, rail, automobiles and ships. These systems, now deployed at major aerospace, locomotive and military manufacturers and research facilities worldwide, provide world-class, high-fidelity simulated environments for use in both closed-loop and open-loop testing. Because Bloomy’s Simulation Systems are largely constructed from COTS components, time to first test can be reduced significantly, and their highly-customizable nature allows your test system experts to provide your unique IP to differentiate your product from your competitors.
-
Product
VME
-
One of the world's leading architectures for high reliability electronics applications is the VME platform.The VME standard is managed by the VME bus International Trade Association, VITA.Embedded computing's most successful bus standard, VME bus, shows no signs of slowing down as it maintains it's position as the industry's de facto standard into the 21st century. The foundation of VME's longevity, namely it's steady rate of technological evolution combined with a commitment to backward compatibility with legacy hardware and software, has been the linchpin of it's popularity for nearly twenty-five years. Today, innovative enhancements to the standard, through the VME Standards Organisation (VSO), continue to improve VME bus' speed, performance and reliability, strengthening it's position as the ideal solution for today's increasingly stringent commercial, industrial and military system requirements (Source: VITA).Data Patterns has implemented a number of standard VME boards, driven by Customer needs for Processor and I/O requirements in this platform. Today, standard modules are available covering the needs of:
-
Product
Semiconductor Lifecycle Management
-
Defense and space applications no longer drive the semiconductor industry. There is such a mismatch between the market life of a modern semiconductor, which can be measured in months to a couple of years, and the platform needs of defense and space platforms, measured in decades.Semiconductor Lifecycle Management (SLiM™) from Teledyne e2v HiRel Electronics solves this headache. We have many years of experience partnering with customers to save cost and lower risk when dealing with platform extensions.
-
Product
Digital DC Micro Volt meter
-
PGP Electronics Private Limited
PGP Electronics Digital DC Micro Voltmeter is a precision measuring tool for the measurement of low DC Voltages. This unit can measure low DC voltages, typically in the order of Micro Volts. This instrument is designed to with stand rugged operation.
-
Product
High Speed Free Space Optical Detectors
-
High speed optical detectors use special photodiodes with high speed electronic circuits to convert fast optical pulses to electrical signals for measurement. Unlike our optical receivers, these detectors do not include a transimpedance amplifier.
-
Product
Electronic Loads/Sinks
-
An electronic load offers the possibility of testing the specimen under different loads. Various load changes are simulated, as they can occur in normal operation. For this purpose, the relevant load current is set in a defined range and electronically controlled. For the test, different operating states are either programmed or entered into the system via an interface (USB, RS-232, GPIB...). For easy handling and quick use, there are four operating modes.
