Modulation Analysis
Measure and analyze radio transmitters and communication systems.
See Also: Modulation, Optical Modulation, Modulation Analyzers, Modulation Meters, MER
-
product
PXI 8-slot BRIC Matrix, 2A, 2-Pole, 456x4, 8 Sub-cards
40-574-108
The 40-574-108 is a 456x4 2-pole matrix and is part of a range of BRIC matrices providing high density configurations capable of switching signals up to 2 A. The modules are available in 2, 4 or 8-slot PXI sizes and are constructed using high quality electro-mechanical relays.
-
product
PCIe-6738, 16-Bit, 32 Channels, 1 MS/s Analog Output Device
785822-01
The PCIe-6738 is a high-speed, high-density analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications such as stimulus-response tests, including acoustic distortion testing, and simulation such as three-phase power simulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24-bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PCIe-6738 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
product
LXI 1GHz 75ohm 16x16 Matrix
60-730-003
The 60-730 is a family of integrated RF matrices suitable for use up to 1.5GHz. The construction of the 60-730 provides a cost effective alternative for RF switching based on microwave switching elements while maintaining a high level of matrix performance. The design is fully scalable, allowing a variety of matrix sizes to be offered in a single family.
-
product
PXI 8 Slot BRIC 348x6 2A 1-Pole Matrix
40-596-106
The 40-596 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 150VDC/100VAC. The 40-596 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
product
PCI Resistor Card 2-Channel 1.5 Ohm To 8.19k Ohm
50-293-024
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Switched Power Distributed Module, CAN Control
H730008xS
The intelligent Power Distribution Unit (PDU) H7300.08xx has two main functions: Distributing the power to each device in a system Switching on the devices sequentially, in order to minimize the inrush current from the switched power supplies, that might affect the contactors.
-
product
PXI 8x2 RF Matrix 1.5GHz 50 SMB
40-750-511
The 40-750-511 is an 8x2 RF Matrix Module suitable for switching frequencies up to 1000MHz. It has a 50Ω characteristic impedance with front panel mounted SMB coaxial connectors. The matrix intended for the easy construction of high performance bidirectional switching systems.
-
product
PXI 2 Slot BRIC 46x16 1-Pole (2 sub-cards)
40-560A-221-46X16
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays.As listed in the manual, page 33, using Slots 1 and 2. Slot 3 can be used only if it is programmed to be used.
-
product
PXI 8-slot BRIC Power Multiplexer, 12-Channel, 12-Pole (5 Sub-cards)
40-571A-303
The 40-571A-303 is a 12-channel, 12-pole 3 Amp Power Multiplexer and is part of our BRIC family. The 40-571A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
product
PXI/PXIe 15W Programmable Resistor Module
40-254-034
The 40-254-034 (PXI) and 42-254-034 (PXIe) are programmable resistor modules with 1 channel which can be set between 2Ω and 102kΩ with 2Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-045
The 40-297A-045 (PXI) and the 42-297A-045 (PXIe) are 6-channel programmable resistors with a range of 2.5 Ω to 2.97 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
16 Channel Power PXI Multiplexer, 2 Pole
40-650-002
A 16 Channel Power Multiplexer, suitable for switching inductive/ capacitive loads up to 5A at 250VAC. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids. It is suitable for applications requiring switching of either mains voltage or DC.
-
product
Signal, Module, Receiver, TriPaddle, 90 Series, 64 Position, w/ Right Angle Contacts
510104187
Primary mating module 510108101. (May mate with other ITA modules, as well.)
-
product
64-CH 16-Bit 250kS/s Multi-Function DAQ Card
cPCI-9116
- PICMG 2.0 Rev 2.1- 16-bit A/D and sampling rate up to 250kS/s- 64-CH single-ended or 32-CH differential input- On-board 1k-sample A/D FIFO
-
product
PXI 8x9 RF Matrix 500MHz 50 SMB
40-725-511
The 40-725 is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz (50Ω version). The 40-725 is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connections, these disconnect the matrix from the external test fixture maximizing isolation and RF performance.
-
product
LXI 75Ω 6:1 Microwave Multiplexer 4-bank 2.5GHz 1.6/5.6
60-820-004
Our 60-820 Microwave Multiplexer range is suitable for switching 75 ohm signals up to 2.5GHz. With the capability of supporting up to 16 banks of 6 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted DIN1.6/5.6 style connectors. A 50 ohm version, the 60-800, is also available covering frequencies to 20GHz.
-
product
Signal Module, ITA, QuadraPaddle, 480 Position, Fully Loaded With Round Posts (610 138 115)
510151108
QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .100” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
product
PXI 8 Slot BRIC 90X16 1-Pole (6 sub-cards)
40-561A-121-90X16
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI 3x3 20GHz Matrix with Loop-Thru
40-787-528-3X3-L
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scalable non-blocking or blocking microwave matrix for frequencies to at least 20GHz. The standard configurations provide up to a 4x4 matrix. More complex matrix can be constructed by adding further switching functions and other devices inside the module.
-
product
SIMRC - 8-Channel 1-Pole Multiplexer
1020-R-8-1-5/1D
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
PXI Precision Resistor Module 4-Channel, 1.5 to 472
40-297-120
This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
LXI Optical Switching - 4x4 Matrix Plugin Module
65-280-321
The 65-280-321 4x4 matrix is part of the 65-280 and 65-281 ranges of optical plug-in modules offering matrix & insert/bypass or multiplexer & SPST topologies respectively with all models based on MEMS fiber optic switches and available in various populations per plugin. In addition, a choice of different connector styles to suit most applications is offered: FC/APC (for optimal performance), FC/PC, SC/PC and ST for general applications and LC for high density applications. They use MEMS (Micro-Electro-Mechanical-Systems) based optical switches to route signals between terminals by redirecting the optical signal. This is achieved using micromechanical mirrors driven by a highly precise mechanism activated via an electrical control signal.
-
product
PXI 12-Slot BRIC Matrix, 308x4 1-Pole (7 sub-cards)
40-562B-321-308X4
The 40-562B-321-308X4 is a high density BRIC12 matrix module with a size of 308x4 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
LXI High Density 64x64 2 Matrix With BIRST
60-552-027
A high-density single pole LXI matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
product
NI-9222 , ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
783283-01
±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9222 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9222 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9222: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
product
PXIe-5673E, 6.6 GHz PXI Vector Signal Generator
781263-01
6.6 GHz PXI Vector Signal Generator—The PXIe‑5673E is a wide-bandwidth module that, when combined with the appropriate software, can generate a variety of signals. With the Modulation Toolkit for LabVIEW, it can generate different waveforms including AM, FM, CPM, ASK, FSK, MSK, PSK, QAM (4‑, 16‑, 64‑, and 256‑QAM), multitone signals, arbitrary waveforms, and many others. In addition, you can combine these vector signal generators with standard-specific software to generate signals for GPS, GSM/ EDGE/WCDMA, WLAN, WiMAX, DVB‑C/H/C, ISDB‑T, ZigBee, and others. With PXIe‑5673E stream‑from‑disk capabilities, you can generate continuous waveforms that are up to several terabytes in length.
-
product
PXI 12-Slot BRIC Matrix, 55x16 1-Pole (5 sub-cards)
40-562B-321-55X16
The 40-562B-321-55X16 is a high density BRIC12 matrix module with a size of 55x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
LXI 50Ω RF Matrix - 2.4GHz
Pickering's LXI 50Ω RF Matrix - 2.4GHz design permits any single Y input to be connected to any single X input, permitting the concurrent connection of 16 RF paths. All signal paths are bi-directional permitting any connection to be used as an input or an output. These matrices can be supplied in a variety of configurations based on Y axis sizes of 4, 8 and 16 and X axis sizes up to 32. The smaller matrix sizes in the range are factory reconfigurable up to the maximum size.
-
product
sbRIO-9227, Non-Enclosed, 50 kS/s/ch, 5 Arms, 24-Bit, 4-Channel C Series Current Input Module
781118-01
Non-Enclosed, 50 kS/s/ch, 5 Arms, 24-Bit, 4-Channel C Series Current Input Module - The sbRIO‑9227 was designed to provide high-accuracy measurements to meet the demands of data acquisition and control applications. It includes built-in anti-aliasing filters. When used with a C Series Voltage Input Module, the sbRIO‑9227 can measure power and energy consumption for applications such as appliance and electronic device test. You can not only measure and meter current and power but also look at quality factors such as noise, frequency, and harmonics. Non-enclosed modules are designed for OEM applications.
-
product
LXI Optical Switching - 1:1 Multiplexer (SPST) Plugin Module
65-281-380
The 65-281-380 1:1 multiplexer is part of the 65-280 and 65-281 ranges of optical plug-in modules offering matrix & insert/bypass or multiplexer & SPST topologies respectively with all models based on MEMS fiber optic switches and available in various populations per plugin. In addition, a choice of different connector styles to suit most applications is offered: FC/APC (for optimal performance), FC/PC, SC/PC and ST for general applications and LC for high density applications. They use MEMS (Micro-Electro-Mechanical-Systems) based optical switches to route signals between terminals by redirecting the optical signal. This is achieved using micromechanical mirrors driven by a highly precise mechanism activated via an electrical control signal.
