Modulation Analysis
Measure and analyze radio transmitters and communication systems.
See Also: Modulation, Optical Modulation, Modulation Analyzers, Modulation Meters, MER
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-020
Precision Resistor Module
The 40-297A-020 (PXI) and the 42-297A-020 (PXIe) are 9-channel programmable resistors with a range of 1.5 Ω to 472 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI Very High Density Multiplexer, 24-Channel, 8-pole
40-670C-022-24/8
Multiplexer Module
The 40-670C-022-24/8 is a 24-channel, 8-pole MUX and is part of a series of very high density multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
Product
PCI High Density Resistor Card 6-Channel, 24-Bit, 0 To 16M Ohm
50-295A-121-6/24
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI BRIC4 FIBO Matrix Dual 80x4 3pin brkout
40-592A-004
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
PXI 12-Slot BRIC Matrix, 630x12 1-Pole (15 sub-cards)
40-558-121-630X12
Matrix Switch Module
The 40-558-121-630x12 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI/PXIe High Voltage Multiplexer, Quad 11-Channel, 2-Pole
42-321-126-HI
Multiplexer Module
The 40-321-126-HI (PXI) and 42-321-126-HI (PXIe) are quad 11-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXI 8x9 RF Matrix 500MHz 50 SMB
40-725-511
Matrix Switch Module
The 40-725 is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz (50Ω version). The 40-725 is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connections, these disconnect the matrix from the external test fixture maximizing isolation and RF performance.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 2-Bank 6GHz SMA
60-802-002
Multiplexer Module
The 60-802-002 is a 4-channel, 2-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber, FC/PC Connectors, With Interlock
42-852A-118-M50-HI
Multiplexer Module
The 40/42-852A-118-M50-HI is a PXI/PXIe 8-channel multiplexer with FC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI/PXIe High Density 2A Multiplexer, 1-Bank, 4-Channel, 32-Pole
42-614D-020
Multiplexer Module
The 40-614D-020 (PXI) and 42-614D-020 (PXIe) 1-bank, 4-channel, 32-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI 4-Slot BRIC Matrix, 66x16 2-Pole (6 Sub-cards)
40-562B-022-66X16
Matrix Switch Module
The 40-562B-022-66X16 is a high density BRIC4 matrix module with a size of 66x16 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Resistor Module 2-Channel 1.5R to 1.02k with SPDT
40-293-121
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
LXI Microwave Multiplexer, SP4T, 9-Bank, 26.5GHz, 50Ω, SMA
60-803-309
Multiplexer Module
Our 60-803-309 is a 9 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXI 5W Programmable Resistor Module, 2-Channel, 1Ω to 239Ω
40-252-113
Programmable Resistor Module
The 40-252-113 is a programmable resistor module with 2 channels which can be set between 1Ω and 239Ω with 1Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
PXI High Voltage Programmable Resistor Module REDEL Connector
40-230-211-HI
Programmable Resistor Module
The 40-230-211-HI (PXI) and 42-230-211-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 62.1Ω with 0.25Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI Power Multiplexer, 16-Channel, 2 Pole
40-650A-002
Multiplexer Module
The 40-650A-002 is a PXI 16 Channel Power Multiplexer, suitable for switching inductive/ capacitive loads up to 5A at 250VAC.
-
Product
Single 32x6 1-Pole High-Density PXI Matrix Module
40-520-301
Matrix Switch Module
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PCI High Density Pecision Resistor Card, 18-Channel, 2Ω To 239Ω
50-298-013
Programmable Resistor Module
The 50-298-013 is a high density programmable resistor card with 18 channels which can be set between 2Ω and 239Ω with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI BRIC4 2Resource Distributor, 1Bus Matrix
40-569-021
Matrix Switch Module
The 40-569 PXI Matrix BRIC provides a range of high-density bus matrix inputs and resource distributor bussed configurations capable of switching up to 2A and up to 100VDC/70VAC. These large PXI matrix modules are available in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays.
-
Product
NI-9423, 24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module
779009-01
Digital Module
24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module - The NI‑9423 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels, can accept up to 30 V discrete logic levels, and has an LED that indicates the status. The NI‑9423 offers isolation between the input and output banks from channel to earth ground. The NI‑9423 is a correlated digital module, so it can perform correlated measurements, triggering, and sychronization when installed in a CompactDAQ chassis.
-
Product
PXI 8-slot BRIC Power Multiplexer, 8-Channel, 6-Pole (3 Sub-cards)
40-571A-401
Multiplexer Module
The 40-571A-401 is a 8-channel, 6-pole 3 Amp Power Multiplexer and is part of our BRIC family. The 40-571A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
Product
e Data Acquisition 32 ch. Module
CPCI-AD320-6U
Data Acquisition Module
The CPCI-AD320 module provides a 6U high performance data acquisition subsystem. There are 32 thirty-two 100/200 KSPS ADC’s for maximum performance. Or an opt low cost 16 channel version. The Local DSP can be usedto simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digital filtering, etc. Software can be downloaded to the DSP via the CPCI interface.
-
Product
PXI/PXIe High Voltage Programmable Resistor Module, D-Type Connector
40-230-141-HI
Programmable Resistor Module
The 40-230-141-HI (PXI) and 42-230-141-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 201kΩ with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP6T, 26.5GHz, 50Ω, SMA
40-784B-033
Multiplexer Module
The 40-784B-033 (PXI) and 42-784B-033 (PXIe) are triple SP6T 26.5GHz unterminated microwave multiplexers. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
PXI 4 Slot BRIC 276x8 Dual Analog Bus (6 sub-cards)
40-560A-021-276X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 2 Slot BRIC 64x12 2A 1-Pole Matrix
40-597-202
Matrix Switch Module
The 40-597 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-597 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI 12-Slot BRIC Matrix, 60x32 1-Pole (12 sub-cards)
40-562B-321-60X32
Matrix Switch Module
The 40-562B-321-60X32 is a high density BRIC12 matrix module with a size of 60x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Dual SP6T Multiplexer 18GHz 50, SMA, Terminated
40-785B-522-T
Multiplexer Module
The 40-785B-522-T is a dual 6-channel 18GHz terminated microwave multiplexer. The 40-785B range of multiplexers are available as a single or dual 6-channel panel mounted multiplexer with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI 4 Slot BRIC 60x16 2-Pole (4 sub-cards)
40-561A-022-60X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP12T, 18 GHz, 50 Ω, SMA, Remote Mount, Failsafe
40-788-221-E
Multiplexer Module
The 40-788-221-E (PXI) and 42-788-221-E (PXIe) are single failsafe SP12T 18 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
