Disturbance
-
Product
Power, Energy and Disturbance Analysers
-
Designed for test and maintenance departments working in industrial or administrative buildings, it can be used to obtain a snapshot of the main features characterizing the quality of the electrical network.
-
Product
Disturbance Recorder
APR64
-
This equipment analyzes and records in real time from 0 to 96 analog channels and from 0 to 1536 digital channels. The APR64 equipment is a system that is completely modular and scalable by adding drawers (digital channels and local and/or remote analog channels by fiber optic, relay, synchronization)
-
Product
AC Power Source
6500 series
-
The global AC power testing requirements demand more sophisticated AC Power Source that is capable of simulating a wide variety of AC line conditions, harmonic waveforms, accurate power measurement and analysis. The Chroma 6500 series Programmable AC Power Source delivers the right solution to simulate all kinds of normal/abnormal input conditions and measure the critical characteristics of the product under test. It can be used for R&D design characterization, production testing, and QA verification of commercial, industrial, and aerospace electronic products. The Chroma 6500 series delivers maximum rated power for any output voltage up to 300 Vac, and at any frequency between 15Hz to 2000Hz. It is suitable for commercial applications (47-63Hz); for avionics,marine, military applications at 400Hz or higher frequency; or for electrical motor, air-conditioner test applications at 20Hz. All models generate very clean sine or square waveforms output with typical distortion less than 0.5%. The Chroma 6500 series has built-in Direct Digital Synthesis (DDS) Waveform Generator to provide user programmable high precision waveform. For testing products under AC line distortion conditions, clipped sinewave can be generated with 0% to 43% distortion and amplitude from 0% to 100%. It also can simulate all kinds of power line disturbances such as cycle dropout, transient spike, brown out, phase angle, voltage and frequency ramp up (ramp down), etc.. Up to 30 harmonic waveforms are factory installed, and testing for compliance to AC line harmonic immunity standards can be easily achieved in the field.
-
Product
Programmable AC Power Source
LSX Series
-
The LSX Series consists of a range of fully featured, single and three phase AC Power Sources. Available models range from 1.5kVA to 6kVA with an advanced programmable controller sporting a color touch screen user interface. Cost effective and fully programmable for both basic frequency conversion as well as advanced AC power line disturbance test and ATE applications. For applications not requiring advanced features, a basic function set M version of the LSX is available as well.Note: The LMX Series is not CE marked yet at this time.
-
Product
6 GHz ProBus2 Differential Probe with Dx10-SI Solder-In Tip
D610-A-PB2
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Stimulus Induced Fault Testing
SIFT
-
SIFT allows for the analysis of numerous stimuli to identify speed, fault, and parametric differences in silicon. The heart of the SIFT technique revolves around intentionally disturbing devices with external stimuli and comparing the test criteria to reference parts or timing/voltage sensitivities. Synchronous interfacing is possible to any tester without any wiring or program changes. The system can be based on either a motorized probe station or portable microscope stand for test head applications.
-
Product
NIST Calibration for D400A-AT
D400A-AT-CCNIST
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
MEGMET 500 D
PU 590
-
The instrument PU 590 is intended for measurement of the insulation resistances and voltages in insulated IT networks, signalling and safety systems or at presence of disturbing voltage. PU 590 can also be used for common measurements of the insulation resistances. It complies with the requirements of the CSN EN 61557-2 ed.2 and CSN EN 61010-1ed.2 standards.
-
Product
QuickLink Solder-In Starter Pack for use with Dx10 Amplifier
Dx10-QL-3SI
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Bandwidth-Controlled Seismic Source
eSource
-
Teledyne Bolt, Inc. has engineered a new type of airgun designed to reduce the potential impact of seismic acquisition operations on marine life while also delivering optimal bandwidth for subsurface imaging. eSource is designed to reduce the high-frequency components believed to have most potential for causing disturbance to marine life while retaining the low-frequency components critical to seismic exploration.
-
Product
Auto-Correlator
FR-103TPM
-
The FR-103TPM is a high resolution, easy-to-use Autocorrelator for Two Photon Microscopy. It can be introduced into the beam path without disturbing the optical alignment, with the detector package replacing the sample.
-
Product
NIST Calibration for D600A-AT.
D600A-AT-CCNIST
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
WaveLink Dx10-PT Adjustable Positioner Tip Kit. Includes XYZ Positioner Assembly
Dx10-PT-KIT
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
QuickLink Solder-In Starter Pack for use with Dx20 Amplifier
Dx20-QL-3SI
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Software
GüVü
-
For efficient field deployments, GüVü allows you to check the integrity of your installation instantaneously. GüVü displays waveforms, orientation, temperature and humidity data without instrument disturbance.
-
Product
AC Power Source
-
AC power source 61500 series sets up the new standard for high performance AC power source. It equips with all powerful features such as power line disturbance (PLD) simulation, programmable output impedance, comprehensive measurement functions, wave-shape synthesis and regulation test software.
-
Product
Voltage Probe
VOL-PBE
-
• EMI Receiver equipped with voltage probe can test disturbance voltage from load terminals or control terminals
-
Product
MP CI set
-
The MP CI set up to measure coupling impedance is used to determine EMC characteristics of connectors and cables. The coupling inductivity defines the coupling inductance of external disturbance on the shield or on the ground with the desired signals. If the coupling inductivity is considered in the construction set-up and the pin or wire assignment of connectors or cables, then the connectors or cables will be more interference-resistant. The MP CI set-up for measuring coupling impedance can be used for following measurements at connectors or cables: 1. measurement of a single signal (common mode) 2. measurement of a symmetrical signal (common mode) 3. measurement of a symmetrical signal (differential mode)
-
Product
Power Quality Software
-
Save Time and Improve Accuracy When Troubleshooting AnswerModules® are proprietary algorithms that convert raw power quality event data into precise answers to determine the source and cause of the disturbance. Read More
-
Product
Static Control Devices
-
Panasonic Industrial Devices Sales Company of America
There are many production processes where electrostatic charges disturb smooth operation. To eliminate static, Ionizers are used.Whether the application is for the Semiconductor industry where the components are extremely sensitive and can even be damaged by high electric static charges or for the packaging industry, where plastic sleeves or foils tend to stick to each other, Panasonic has a solution to neutralize electrostatic charge.
-
Product
WaveLink Temperature Extension cables for Dx10
Dx10-HiTemp
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Smaet LDV III
-
A Laser Doppler Velocimeter (LDV) measures fluid velocity by utilizing coherence of laser light. It detects the Doppler shift frequency of the scattering light of particles in the fluid and calculates the velocity of the particles (fluid). With a LDV system, non-intrusive measurements without disturbing the measuring object, liquid or gas flow, are achieved. No calibration is necessary and reverse flow measurements at a high resolution is also possible. The LDV system provides the absolute value of the flow velocity with accuracy.
-
Product
Signal Analysis
Synchronous Accumulation (Order Analysis)
-
Order analysis is one of the most convenient and efficient methods for diagnostics and balancing of rotating mechanisms and transmission gears. With an RPM sensor and a vibration sensor, it is possible to study the time characteristics of gear vibration signals. It is a well-known fact that a signal from a vibration sensor is affected by signals from other sources. To tune out from the disturbing signals, the synchronous signal accumulation method is used. For each shaft rotation, the RPM sensor provides a rotation mark. This signal serves as a triggering strobe for the vibration sensor signal sweeping. The obtained signal sweeps are combined. All the sources of the signals related to the shaft frequency (frequency of rotation) are accumulated and increased in the accumulator linearly proportionally to the N number of rotations. All other signals that are not correlated with the shaft frequency are accumulated proportionally to N1/2 and in case of a greater number of averagings, the useful signal exceeds the interference level.
-
Product
Low Power Programmable AC Source with Transients
61500 Series
-
Chroma Systems Solutions, Inc.
Power:500VA (61501)1500VA (61503)2000VA (61504)4000VA (61505)Voltage range: 0-150V/0-300V/AutoCompact size and weight attributable to advance PWM technologyAC+DC output mode for voltage DC offset simulationProgrammable slew rate setting for changing voltage and frequencyLow output impedance for testing IEC 61000-3-2 (61505)Programmable output impedance for testing IEC 61000-3-3LIST, PULSE, STEP mode function for testing power line disturbance (PLD) simulation capabilityIEC 61000-4-11 voltage dips, short and variation simulationHarmonics, inter-harmonics waveform synthesizer for testing IEC 61000-4-13Programmable voltage, current limitComprehensive measurement capability, including current harmonicsHigh output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlTTL signal which indicates output transientAnalog programmable interface3 units combined to 3-phase power outputEasy-use software for operation and IEC regulation testOptional GPIB and RS-232C interface
-
Product
20 Bit / 2 MS/s Waveform Digitizer
WFD20
Waveform Digitizer
The WFD20 is a 20 bit Waveform Digitizer for medium-speed / high resolution waveform capturing and analyzing. The module combines an excellent dynamic performance with a very high DC accuracy. The module features a fully differential input path to reduce common-mode level disturbances.
-
Product
6 GHz ProBus2 Differential Probe with Adjustable Tip
D600A-AT-PB2
Differential Probe
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
EFT Immunity Measurement
EFT61000-4
-
EFT immunity tester EFT61000-4 is specially designed according to the characteristics and requirements of EFT measurement and it is an ideal disturbance source of EMS measurement. They have fine performance, such as high stability, high reliability, easy to use etc. It meets the standard requirements of IEC 61000-4-4, EN 61000-4-4, GB/T17215.301, GB/T17215.322 and GB/T17626.4. EFT61000-4 has LCD display in both English and Chinese.
-
Product
Multi-Function Recorder
TR-2000
-
For all types of power system events, the TR-2000 Multi-Function Recorder provides all the information you need to capture the complete picture. With the true integrated functionality of the TR-2000, you have one place for all your answers. Simultaneously perform: transient recording, disturbance recording, phasor measurements, power quality analysis, and sequence of events recording.
-
Product
NIST Calibration for D620-A
D620-A-CCNIST
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Ionizers
-
Panasonic Automotive & Industrial Systems Europe GmbH
There are many production processes where electrostatic charges disturb smooth operation. To eliminate static, ionizers are used. One typical field of application is the semiconductor industry where the components are extremely sensitive and can even be damaged by high electric static charges. Another example is the printing industry: Here friction between the rollers and the paper generates static. The static makes the paper cling and not move correctly through the printing machine. Especially when printing on vinyl or plastics, electrostatic charges need to be removed. In the packaging industry, plastic sleeves or foils tend to stick to each other, which can be prevented with an ionizer eliminate static. A general problem in assembling processes is the adhesion of dust and dirt particles. Contamination of workpieces can be prevented by having static eliminators neutralize and blow away undesired particles.
