Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
Product
Cable, 96-Pin Female, Screwlocks To 100-Pin Male, Screwlocks, 1.27mm Pitch, 1m
A096SFR-100SMR-5A100
Cable Assembly
The 96-Pin to 100-Pin 1.27mm pitch Adaptor Lead is constructed from 7/36 (28AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. M2.5 screwlocks are provided on the 96-Pin connector and 4-40 UNC screwlocks on the 100-Pin connector.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-415-005
Microwave Transfer Switch
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-010-013
Microwave Transfer Switch
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
PCI 50xDPST Reed Relay Card
50-115A-122
Reed Relay
This is the 50xDPST version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
- RS-422 to Fiber Optic Converter
Model 272A
-
FEATURES: Data Rate to 2.5 MBPS; Full Duplex TD and RD; ST Connectors; Extends RS-422 Network up to 2 km (6,600 ft). The Model 272A provides the capability of performing an interface conversion between full duplex, RS-422 signals and their equivalent for fiber optic transmission.
-
Product
Eurocard Plugbord
4614-3
-
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 96-pin DIN connector. Pad-Per-Hole both sides. Voltage and ground bus around board perimeter on both sides. For solder, Wire-Wrap or mixed wiring methods. Pad and bus surfaces solder-coated for user convenience. Row and column legends provided.
-
Product
CB-485A, 10-Pin Female RJ50 to 10-Pin Female Screw Terminal, DIN Rail, Serial Communication Terminal Block
778674-01
Terminal Block
10-Pin Female RJ50 to 10-Pin Female Screw Terminal, DIN Rail, Serial Communication Terminal Block - The CB-485A is a connector block for RS-485 serial communication over RJ50 cables that mounts to the DIN rail. It features ten screw terminals and a female RJ50 connector.
-
Product
PXI/PXIe Microwave Relay, Quad SPDT, 18 GHz, 50 Ω, SMA, Failsafe
42-780B-524
Relay
The 40-780B-524 (PXI) and 42-780B-524 (PXIe) are quad failsafe SPDT 18 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
Optical Switches
Optical Source
Fast and reliable optical switches to streamline your test procedures. Can be customized with a wide range of switch configurations, fiber types and connectors.
-
Product
GMCT 26-Pin RF Cable Assembly, 75Ω, Male To Unterminated, 0.5m, RG179 Cable
40-979-726-0.5m-FU
RF Cable Assembly
This 0.5m long cable assembly is part of a range of cables suitable for applications using the Positronic 26-pin GMCT 75Ω RF connector. It is constructed from RG179 silver plated copper clad steel cable with FEP insulation and a bandwidth of 500MHz. Screwlocks are provided to secure the connector to the associated product.
-
Product
LXI Microwave Multiplexer, SP4T, 8-Bank, 18GHz, 50Ω, SMA
60-803-108
Multiplexer Module
Our 60-803-108 is a 8 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
Power Supplies
CTI-700B
-
With dual 80mm smart fan cooling your system, the CTI-series keeps running smoothly. It comes with an automatic setting to adjust the fan speed according to the level of heat. The hotter your system, the faster the fan spins, and the faster your system cool. With great ventilation, you no longer have to worry about your system overheating. It is dual PCI-E connector ready (700W only) for your graphic rendered fun.
-
Product
Pico-ITX SBC With 4th/5th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, DisplayPort/LVDS, LAN And Audio
PICO880
-
The PICO880 is an extremely compact Pico-ITX SBC with onboard 14nm 5th generation Intel® Core™ i7/i5/i3 and Celeron® processors. The palm-sized PICO880 enhanced performance enables greater multitasking at low power meeting the needs of the growing retail mobile device marketplace. The industrial grade embedded SBC is built to withstand wide temperature conditions, ranging from -20°C to +70°C (-4°F to +158°F). Designed with expandability in mind, the tiny embedded board has a full-size PCI Express Mini Card slots with mSATA support. The Axiomtek PICO880 also provides two flexible board-to-board connectors that integrate audio, four USB 3.0, one PCIe x1, one DisplayPort, two UARTs, LED, and power on/off interfaces. The pico-ITX motherboard PICO880 is equipped with standard features such as one DDR3L SO-DIMM with up to 8 GB memory capacity; one USB 2.0 port; one SATA-600 interface, one 10/100/1000Mbps Ethernet port that supports Wake-on-LAN, PXE; one DisplayPort and LVDS display interface with integrated Intel® HD graphics 5500 and 6000 that delivers high-resolution Ultra HD 4K display support for immersive visual retail experience. The single board computer also offers two optional expansion boards, AX93275 and AX93276 for additional RS-232/422/485, USB 3.0, HDMI, VGA and LAN ports. This outstanding embedded SBC runs well with Windows® 7 and 8.1 operating systems.
-
Product
SP5T RF Pin Diode Switches To 12 GHz
-
Pulsar Microwave's 5-way RF switches cover bands from 300 MHz to 12 GHz in both absorptive and reflective configuration. These SP5T switches have a rating of 200 mW maximum input power and a switching time of 100 ns. They are specified with a minimum isolation of 60 dB and most models maintain a VSWR of 1.6:1 or better on all ports. The SP5T switches are driven by TTL logic control circuitry and require both positive and negative 5-volt supplies for operation. A 9-pin D-SUB connector provides the interface for the power and logic voltages.
-
Product
SH37F-P-4, 37-Pin Female to Pigtail Shielded I/O Cable, 12ft
778620-04
Multifunction Cable
37-Pin D-SUB Female to 37-Pin Bare Wire Female, 12 ft, Pigtail I/O, Shielded Multifunction Cable - The SH37F-P-4 connects compatible CompactRIO modules to accessories or cables with bare wire connectors.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-215-001
Microwave Transfer Switch
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
Near Field Probes 1GHz - 10 GHz
SX set
-
The SX1 set consists of 3 passive near field probes for making measurements in the development phase of E-field and magnetic field with a high clock frequency in the range from 1 GHz to 10 GHz. The probe heads of the set SX allow for measurements close to electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors, to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through trained use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They have an internal terminating resistance.
-
Product
Standard Mechanical Calibration Kit, DC To 3 GHz, Type-N, 75 Ohm
85036B
Mechanical Calibration Kit
The Keysight 85036B calibration kit contains precision 75 ohm type-N standards used to calibrate Keysight network analyzers for measurement of devices with 75 ohm type-N connectors. Standards include fixed terminations, open circuits, and short circuits in both genders. This kit is specified from dc to 3 GHz.
-
Product
200-Pin LFH Cable Connector, Male
92-961-200-M
LFH Male Connector
This connector is designed to allow users to directly terminate with soldered connections to the 200 pin LFH connector. Please note; This product is supplied without the backshell shown in the image above.
-
Product
LXI Microwave Multiplexer, SP4T, 13-Bank, 67GHz, 50Ω, SMA-1.85
60-803-813
Multiplexer Module
Our 60-803-813 is a 13 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXI Single 2 x 2 Fibre Optic (M Mode)SCM62.5
40-860-212-M62.5
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber.
-
Product
Rugged PC Compatible
SYS-ITX-P-3800
-
WINSYSTEMS’ SYS-ITX-P-3800 Series embedded computers pack an impressive feature set into a small form factor Pico-ITX design. The SBC’s are based on the Intel E3800 processor family which provides CPU and graphics performance. The SYS-ITX-P-3800 is a perfect choice for applications requiring low power and Intel performance in a small form factor package with industrial connectors and I/O.
-
Product
Digital I/O Board, 32 Isolated I/O Channels, 24V +special EEPROM & TTL IO Port
APCI-1500-PULS
-
PCI interface to the 32-bit data bus Connector compatible to PA 1500 Connector and software compatible to CPCI-1500 16 isolated input channels, 24 V, including 14 interruptible 3 software-programmable counters/ timers 16 isolated output channels, 10 to 36 V, output current 500 mA Timer-programmable watchdog for the reset of the outputs"-PULS" version has a special EEPROM and a TTL IO port added at end of cardDiagnostic report through status register in case of short-circuit, overtemperature, voltage drop or watchdog Interrupt triggered through watchdog, timer, error One ground line for all inputs and one ground line for all outputs
-
-
Product
Active Splitter for CATV/SATV
HGS02
-
Hangzhou Huatai Optic Tech. Co., Ltd.
*Excellent, zinc alloy die-casting chassis. *All ports can be passed by DC.* 75ΩBritish F-type connector.* With separate holes for easy installation. *Low noise, high isolation design. *Frequency 950-2150MHz.
-
Product
Ethernet Flying Lead
-
Qualified 100m Subsea Ethernet jumpers designed for data transmission and real-time situational awareness and monitoring. The typical Ethernet harness system consists of wet-mateable, Nautilus connectors, Nautilus penetrators, and pressure balanced, oil-filled (PBOF) hose conduits. Internally, the Ethernet signals are transmitted over custom Ethernet cabling sealed to seawater ingress by two independent barriers. Seven and 12-way configurations are available. Subsea connection of the harnesses may be accomplished by ROV, Diver-Mate or Stab-Plate applications. For Ethernet needs above 100 meters, see Extended Ethernet Flying Leads.
-
Product
8 Ports 1GbE RJ-45 Module
NMC-0806
Network Mezzanine Card
Ideal for multi-segment network deployments and inline security monitoring. 2x Intel® i350_AM4, 8 ports RJ45 connector, 2 x PCIe x4, Gen2.
-
Product
Cable Assembly, Receiver, 36", QuadraPaddle to 2 x 78-Pin Female D-Sub Connectors
540112050240
Cable Assembly
Cable Assembly, Receiver, 36", QuadraPaddle to 2 x 78-Pin Female D-Sub Connectors
-
Product
Cable, 96-Pin 1.27mm Pitch Female, Spring Latches To 2 X 50-Pin, Female, Adaptor Lead, 0.5m
A096SFR-02F050Z5A050
Cable Assembly
The 96-Pin Pitch to 50-Pin Adaptor Lead is constructed from 7/36 (28AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Metal Spring Latches are provided on the 96-Pin connector and strain relief is via latch clips for the 50-Pin connectors.
-
Product
PXI/PXIe Microwave Relay, Triple SPDT, 12.4 GHz, 50 Ω, N-Type, Remote Mount, Failsafe
42-780B-513-E
Relay
The 40-780B-513-E (PXI) and 42-780B-513-E (PXIe) are triple failsafe SPDT 12.4 GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
