Masters
See Also: Slave, Master Jumpers
-
Product
Homogenizers
Sample Preparation
-
Sample preparation is critical to master molecules extraction from biological samples. Bertin Instruments offers efficient and flexible Precellys homogenizers for grinding any samples prior to analysis.
-
Product
Modbus TCP Gateway
SI-485MB
-
SI-485MB is a Modbus gateway to convert bi-directionally Modbus RTU/ASCII of serial interface to Modebus TCP of Ethernet. The firmware for gateway process supports Modbus TCP master mode and Modbu TCP slave mode and supports all the current ModbusRTU/ASCII register and command conversion. The robust metal body, broad range of temperature, wide input voltage range, and the support for installation by options such as 35mm DIN rail and wall bracket allow you to use it for factory automation without worry.
-
Product
Audio Mastering Magnetic Recording Heads
-
International Electro-Magnetics, Inc.
*Tape and Film*Standard Replacement*Instrumentation Quality*Custom Formats
-
Product
IO-Link
-
The IO-Link® interface simplifies communication to smart sensors and actuators, combining signaling with power-over-cable technology. It has become one of the key devices as industrial automation systems are growing more interconnected and intelligent to accommodate demands for centralized control and optimized production. Analog Devices implements both device PHY and master PHY interfaces (COM1/COM2/COM3). Designing with harsh industrial environments in mind, the master 4-port IO-Link power and communications interface, as well as the IO-Link transceivers featuring Integrated Step-Down Regulators and LDO with ±60V cable interface protection provide the required ruggedness. Optimum EMC performance is achieved with adjustable current limit and slew rate transmitters. Automatic wake-up request (WURQ) generation and an output supply current boosting capability for device startup are also available. Additional components integrate a 300 mA step-down (buck) regulator and a 150 mA LDO to supply all the power required for internal electronics in an connected sensor or actuator.
-
Product
AS-Interface Masters
-
*Simplified system installation by means of AS-Interface wiring system*AS-Interface - perfectly complements for different field buses or industrial Ethernet*Graphic user interfaces for clear configuration and diagnostics*High-performance controllers and gateways
-
Product
XCITE 1100 Field Test Series
-
The Xcite 1100 Field Test Series uses the same Exciter Heads and Master Controller as the 1100 Laboratory Series but replaces the 5 GPM 3-Phase Hydraulic Power Supply with a field portable 1.2 GPM Single Phase Power Supply. While providing the same 3000 PSI pressure, the field test unit is switch selectable from 110 V (20 A) to 220 V (10 A) single phase power.
-
Product
Sand And Dust Test Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Sand and dust test chamber is also referred as dust-proof chamber, which is able to simulate the sand storm by putting the test piece in the chamber to judge the damage of sand-and-dust weather to products. Equipment is mainly applicable to determination of sealing performance of product shells based on the IPX5 and IPX6 degrees. Testing machine features a flow of air carrying dust in a vertical circulation, resulting in cycle use of sand during the test. Sand and dust testing has great significance to master the specimen’s performance to defend the penetration of dust particles, to withstand the abrasion of sands.
-
Product
PXIe-8623, 4-Port, 100/1000BASE-T PXI Automotive Ethernet Interface Module
787992-01
-
PXIe, 4-Port, 100/1000BASE-T PXI Automotive Ethernet Interface Module - The PXIe-8623 is a 100/1000BASE-T unshielded twisted pair (UTP) PXI Automotive Ethernet Interface Module that helps you develop applications with the NI‑XNET driver. With the PXIe-8623, you can develop applications that require Ethernet to test and validate automotive electronic control units (ECUs). The PXIe-8623 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, making synchronization with an external network as well as the rest of a PXI system possible. Additionally, the PXIe-8623 features LEDs on the front panel to help you monitor the network link and activity.
-
Product
VME Data Acquistion System
ADM-31
-
The VME-based ADM31 data acquistion system supports up to 48 differential or up to 96 single-ended analog inputs. The ADM31 control card is an intelligent A/D subsystem master or slave device that controls the analog A/D cards. Up to two A/D cards can be configured with the control card to complete the A/D system.
-
Product
Local Bus Master & Target Bridges
PCI 9052
-
The PCI 9052 PCI I/O Accelerator provides low cost connectivity for PCI slave designs. It is specifically targeted at easing the transition of existing ISA designs to the more feature rich and performance oriented PCI bus.
-
Product
One Phase Electric Power/Energy Calibrator
MC133
-
The MC133 master unit model is a one phase electric power/energy calibrator. It can supply the device under test with single phase precise voltage and current with calibrated phase shift along with DC voltage and current capability. Output voltage can be set in five ranges up to 280V and output current in six ranges up to 30A. Simulated electric power can be set independently for each phase. Frequency can be set from 15Hz to 1 kHz with resolution 0.001Hz to 0.01Hz. The MC133 Calibrator is equipped with 5 1/2 digital DC meter with DC ranges 20mA or 10V for direct calibration of various types of power transducers and wattmeters.
-
Product
XCITE 1100-5 Inertial Mass Excitation System
-
The 1100-5 Inertial Mass Modal Excitation system allows the testing of structures where backup fixturing is not available or possible. Accelerating an internal mass with the closed loop hydraulic excitation system generates the inertial forces. The compression control of the Xcite Master Controller maintains a constant force over a frequency sweep by continuously altering the drive signal to maintain the required dynamic force level.
-
Product
PCI Express, Analyzer Software Included, IEEE 488 GPIB Instrument Control Device for Windows - Low Profile, Onboard GBIP Analyzer
780936-01
-
The PCIe‑GPIB+ combines an IEEE 488 controller and an analyzer on one device for computers with PCIe slots. You can use this device to integrate an instrument into your system using GPIB as well as to troubleshoot and solve GPIB hardware and software problems. The PCIe‑GPIB+ achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
SparkFun MicroMod GNSS Carrier Board (ZED-F9P)
-
With GNSS you are able to know where you are, where you're going, and how to get there anywhere on Earth within 30 seconds. This means the higher the accuracy the better! GNSS Real Time Kinematics (RTK) has mastered dialing in the accuracy of their GNSS modules to just millimeters, and that's why we had to put it on this board! With the flexibility of the MicroMod's M.2 connector, you can easily test and swap out different MicroMod processor boards for your application. Simply match up the key on your board's beveled edge connector to the key on the M.2 connector and secure the boards with a screw. This means solderless access to the ZED-F9P modules features via UART1, UART2, SPI, and I2C ports!
-
Product
USB-8452, 3.3 MHz I2C, 50 MHz SPI I2C/SPI Interface Device
781964-03
-
The NI USB‑8452 is a master interface for connecting to and communicating with inter-integrated circuit (I2C) and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8452 is a bus-powered, portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices, toggling LEDs, or strobing convert and data ready lines common to analog converter chips. You can physically place the USB‑8452 more closely than PCI interfaces to I2C/SPI devices, which reduces I2C bus length and minimizes noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
Wire Harness Tester
Panther4HT Master- Slave DSU
-
Qmax Test Technologies Pvt. Ltd.
The Master- Slave DSU based Panther4HT Wire Harness tester is designed for testing and verifying electrical connections in a cable, harness, backplane or any other wired assembly. It offers unique Qmax MASTER - Slave concept and SATELLITE UNIT Options to avoid looping back of cable to the ATE. All Satellite Units communicates the measurements through LAN interface which is very useful for on-board applications in Aircrafts / Ships and similar applications where large cable looms are used. This innovative concept will eliminate the long adapter cables and hence storing, maintaining and re work of these kind of cables are avoided. Furthermore single Master Controller Unit (MCU) is used to control not only all the satellite units , but also communicate with all satellite units through Ethernet Communication port. A single reference Cable is used to link the all the satellite units with the Master Controller in controlled loop manner is a value add to the product.
-
Product
Comprehensive Simulation of Master, Slave and End Nodes in A 2 B ® Networks
Infotainment Test Device ITD 1024
-
The complexity, cost and weight of audio systems are significantly reduced with the Automotive Audio Bus (A 2 B ® ) from Analog Devices Inc. Regardless of their hierarchical structure or use as master or slave, all A 2 B ® products must be adequately tested before use. This applies, for example, to HiFi amplifiers/loudspeakers, head units, eCall systems, microphones, vibration/noise suppression units, actuators or sensors.Our small and very compact infotainment test system ITD 1024 takes on this task for you: It comprehensively and extremely reliably tests all A 2 B ® signals and communication in all phases of the product development process - during development, for validation and in production.
-
Product
Analysis Tool
CANalarm
-
The CANalarm is a low priced analysis tool that can be installed in the bus permanently. It makes it possible to build up a separate and redundant monitor without change of configuration and program of the master controller. It works passive and is therefore non reactive
-
Product
Highly Shielded Phase Stable Assemblies
PhaseMaster® Enhanced
-
Does your application require cable assemblies offering some combination of phase stability and low loss, significant shielding effectiveness and increased durability?Consider Phase Master® 190E as your design-in option.Compared to similar phase stable cables, the Phase Master® 190E’s enhanced, multilayer shield construction yields:- A high level of phase stability vs. temperature- Reduced insertion loss & increased amplitude stability - Increased shielding effectiveness (120 dB @ 1 GHz, min)- Increased mechanical durability, especially torsion resistanceGreater connector retention (>40 lbs straight pull with SMA connectors)
-
Product
10A Continuity Tester
EQUITEST
-
EQUITEST is connected to its master unit via C2050 cable and to the mains for power supplying.Please refer to the user manual of your HT installation safety tester for the compatibility to EQUITEST.
-
-
Product
I²C/SPI Interface Device
-
The I²C/SPI Interface Device is a master or slave interface for inter-integrated circuit (I²C), or master interface for serial parallel interface (SPI) devices. With plug-and-play USB connectivity, the I²C/SPI Interface Device is a portable solution to communicate with consumer electronics and integrated circuits. The I²C/SPI Interface Device can be physically located more closely to I²C/SPI devices than PCI interfaces, reducing I²C bus length and minimizing noise problems. The I²C/SPI Interface Device supports I²C rates up to 250 kHz and SPI rates up to 50 MHz, and it also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I²C devices or toggling LEDs.
-
Product
Interface Adapter
DMX-10
-
DMX-10 is, all-in-one ready to use PCIEx to I2C/SPI/GPIO Interface adapter based on system with FPGA and 1x PCIEx PHY. DMX-10 converts PCIEx transactions into the I2C, SPI master or slave transactions and GPIO control functions. DMX-10 turns your PC running Windows, DOS, Linux, MacOS or any embedded OS with PCI support into comprehensive general purpose bus master or slave adapter.
-
Product
Modbus RTU Analog Input Modules
-
The Datexel range of Modbus RTU analog input cards for both RS485 and RS232 with Modbus or ASCII protocol can be combined with the DAT9000 series of Modbus Masters. A choice of input cards or modules are available and have various optional inputs such as Voltage, Current, Thermocouples, RTD, and Resistance. Also a choice of 2, 4, 8 channel options are available. The DAT3011 is a Modbus RTU Slave with 1 selectable universal input (Thermocouples, RTD, mV, RTD's or Resistance), 2 x 4-20mA or 0-10V input and 2 x4-20mA outputs. The DAT3011 also has 3 digital inputs and 3 relay outputs. Each module is isolated from each other and is set up using the DAT3000 software Development package which is free of charge from the Datexel download web page. Datexel also has universal input modules. An 8 channel analog input card is available making the DAT3000 series a very economical solution to large and small scale Data Acquisition. Combining these analog input cards with the analog output cards, the digital input/output cards and the communication devices make Datexel the smart choice where Data Acquisition is required.
-
Product
Pronto For Windows
-
Pronto for Windows is Outram’s full-featured Windows-based power quality software designed to extract data from the Outram Power Master family of data loggers and power quality analysers and present it graphically for analysis.
-
Product
PXI Automotive Ethernet Interface Module
-
The PXI Automotive Ethernet Interface Module communicates with Automotive Ethernet so that you can use the NI‑XNET driver or standard networking drivers to develop applications that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). It provides up to four independent endpoints or up to two network terminal access points (TAPs). With onboard hardware timestamping and the ability to act as 802.1AS masters or slaves, the PXI Automotive Ethernet Interface Module can synchronize with an external network as well as the rest of a PXI system.
-
Product
Cylindrical Inductive Proximity Sensor (Built-In Amplifier)
GX-300
-
Panasonic Industrial Devices Sales Company of America
The GX-300 Series of Cylindrical Inductive Proximity Sensors provide state-of-the-art features, enhanced basic performance, improved operability, and an extensive model lineup including IO-Link compatible models that are capable of transmitting sensor data and status information to a host controller through an IO-Link master.
-
Product
Waveform Generators
-
Highland offers waveform generators across a wide range of forms and performance. From simple 4 channel function generators to our flagship arbitrary waveform generators with interchannel modulation, system mastering capability, and unlimited synchronization capability, all of our waveform generators are designed to allow synchronous signal generation for easy integration into end systems.
-
Product
Wireless Test System
WTS-80
-
CETECOM offers a wide range of services and solutions to help companies develop and execute product testing plans to determine a product’s compliance status and master the increasingly complex regulatory issues of the internationalmarket.
-
Product
EtherCAT Master Multi-Axis Motion Controllers
DMC-500x0
-
The DMC-500x0 EtherCAT Controller is Galil Motion Control's newest entry in its latest generation of digital motion controllers. Incorporating all of the features of our flagship Accelera series controller and designed with compatibility and flexibility in mind, the DMC-500x0 allows integration of remote EtherCAT drives into new and existing applications with just a handful of configuration commands. The DMC-500x0 is offered in 1 through 8 axis formats. Axes 1 - 4 can be configured as either local or EtherCAT drives while axes 5 – 8 can be configured for additional EtherCAT drives. Unique to the motion control industry, this ability to mix and match local and EtherCAT drives on the same controller provides increased flexibility for any application. In addition, the DMC-500x0 is fully compatible with Galil’s internal servo and stepper motor amplifiers as well as third party external drives.
