Showing results: 1186 - 1200 of 1830 items found.
-
1RA470 -
Le-tehnika, d.o.o.
Cable tracer is designed to trace wires without damaging the instalations. It has wolume control to increase sensitivity. Power supply is standard 9V battery.
-
Snap Shot™ -
T3 Innovation
Accurately finds cable length, impediments in the cable and conditions at the end of every wire in your data, power, or communications/video system up to 3,000 ft.
-
Circuit Check, Inc.
Higher density more complex circuit boards complicate testing requirements while smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in standard long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board or T-Board®. Circuit Check’s wireless fixture technologies reduce test program debug and maintenance times while easing the ECO process. Thus allowing for the higher level of test performance, the ability to probe smaller denser targets and achieve ultra-high node counts.
-
AI-5620 -
Advent Instruments Inc.
The AI-5620 simulates a single port two wire analog TE (Terminal Equipment) or CPE (Customer Premise Equipment) device. It is designed to measure and analyze signals generated by a CO (central office) line card, VoIP terminal adapter FXS port, or any device utilizing a SLIC (subscriber line interface circuit).
-
#TP150 -
NSI Industries
Make cable tracing easy with Platinum Tools’ Tone and Probe Set. With its steady tone, push-to-scan button and a clear loudspeaker, quickly trace and identify cable locations on jacks or through walls. Wire bundles are easily penetrated with the tapered probe tip and the probe volume is controlled with a thumbwheel. With common send and […]
-
Santronics, Inc.
This sensor can be used to troubleshoot any DC circuit with voltage ranging from 6-50 volts DC. It features an audio and visual alert and a sharp, rust-proof, stainless steel tip that works great for penetrating insulated wires. This sensor also features an extended ground lead with an extra-large alligator clip to ensure a good connection.
-
Shenzhen Everbest Machinery Industry Co.,Ltd.
Non-contact detection of 50 to 1000V ACRugged and double molded caseSuitable for outlets or against wire insulation testingFlashing red LED light indicatorBuilt-in bright flashlight with on/off buttonConvenient size with pocket clipAuto power offSystem self testUse on 50/60Hz circuitsComplete with two AA batteriesCATIII 1000VDimensions: 158 x 21mmWeight: 48g
-
General Tools & Instruments
Stud Sensors such as the MSV100 and MSV350D comprise a category of their own. Each uses electromagnetic induction to sense the presence of (and thereby locate) a stud, pipe, batten, current-carrying wire or other metallic object behind a wall or above a ceiling. The two instruments differ in their choice of the display technology (LED or LCD) used to pinpoint position.
-
MCT 192 -
REINHARDT System- und Messelectronic GmbH
MCT 192 is an easy-to-use high-speed cable tester for testing multi-wire cables and complete backplanes. The multi-contact board is equipped with contacting sockets and connectors common in industries. Fixturing is therefore unnecessary. In case you use connectors which are not supplied with the multi-contact board, you can mount and wire these connectors on a raster plug-in board.
-
34938T -
Keysight Technologies
Use Keysight's 34938T terminal block for the Keysight 34938A 20-channel 5-amp form A switch for discrete wiring. It supports up to 20 AWG wire size typical for < 100 connections or 24 AWG for > 100 connections. The 34938T terminal block is detachable with screw-type connections that provides a flexible method for connecting external wiring.
-
THW-L2 -
Thermtest Instruments
Designed with speed and operational simplicity in mind, the Transient Hot Wire (THW-L2) Liquid Thermal Conductivity Meter is an advanced measurement system for direct determination of the thermal conductivity of liquids and pastes in accordance with ASTM D7896-19. In less than 2 seconds, a single measurement of small volumes of liquids and pastes can be accurately and precisely measured for thermal conductivity. Using a non-stationary measurement approach, the THW-L2 uses rapid test times to limit convective effects for samples with a wide range of viscosities. The THW sensor consists of a 60 mm heating wire that is fully inserted into an isothermal sample. A constant current source (q) is used to heat the sensor wire and the temperature rise is recorded by monitoring the change in electrical resistance of the wire. The slope (m) is determined from the plot of temperature rise vs. logarithm of time and is used in the calculation of thermal conductivity (λ). Liquid samples of high thermal conductivity will have a lower slope, while liquid samples with low thermal conductivity will have a higher slope.
-
MK Test Systems Ltd.
A modular test system, RTS (real time scanner) provides instant test results with minimal interface cables to check wiring during installation.It tests wire harnesses in real time using our micro switching technology, reducing the need for high cost interface cables by around 90%. an innovative best-in-class solution for FAL testing, RTS also offers many benefits for wire harness and sub-assembly manufacturers.
-
8019-1 -
VECTOR Electronics and Technology, Inc.
Single sided board, circuit pattern one side only, holes not plated thru.Ideal for common busses, signal line running longer distances, for hard wire of test circuits or discrete components. Tracks run close to board edges. 3U X 160mm Eurocard size will fit into 3U DIN Metric subrack.
-
Series 152FB -
Aries
Fusion Bonded Cable Jumpers. Aries Series 152FB Fusion Bonded Cable Jumpers are flexible...plug them directly into PC boards or sockets. Stranded wire conductors are fusion bonded with an overcoat of tin for easy soldering or socketing. Each jumper is shipped with protective tabs on both ends for maintaining proper conductor spacing.
-
Celadon
Cables are designed and manufactured by Celadon. Cables are available in lengths custom to the half-meter, and can be manufactured with a variety of industry standard connectors, such as coaxial, triaxial, Type8, Edge 24/48 or 35/70, DSub 9, 15, 25, or 50; or advanced multi-contact. Depending on the overall size of the final product, an anti-abrasion sheath may be used to prevent wire wear.