Power Monitors
-
Product
SpaceWire Monitors
-
This section details the 4Links range of high-performance test equipment that is used to monitor SpaceWire networks. These devices are attached to your SpaceWire systems and then can be accessed via Gigabit Ethernet, using the standard TCP/IP family of protocols, so that they can be controlled remotely (for instance, by partners collaborating on a mission).
-
Product
PXI-4110, 3-Channel, 20 V, 1 A, 46 W, PXI Programmable Power Supply
779647-11
Programmable Power Supply
3-Channel, 20 V, 1 A PXI Programmable Power Supply—The PXI‑4110 is a programmable DC power supply. It is an excellent general-purpose, single-quadrant power supply for design validation and manufacturing test applications. The PXI‑4110 has two isolated and a single non-isolated supply channel, all capable of generating up to 1 A per channel. You can program the voltage setpoint and current limit as well as the voltage and current readback/measurement functionality. You can also combine channels for higher voltage or current.
-
Product
RF Safety Monitoring
MVG EME Guard Plus
-
The EME Guard Plus is designed to record EMF exposure near antennas while continuously monitoring potential over-exposure. Lighter than the previous model, the EME Gaurd Plus makes it easier for workers to wear on the job. The longer battery life and extended memory capacity enable more measurements to be recorded.
-
Product
High Power, Contact, Receiver, 150 Amps, 2 AWG
610149101
Power Contact (Receiver)
Primary mating contact 610150101. (May mate with other ITA contacts, as well.)
-
Product
Thermocouple Power Sensors
N8487A
Power Sensor
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
10 MHz to 18 GHz LAN Wide Dynamic Range Average and Peak Power Sensor
L2062XA
Power Sensor
The Keysight L2062XA is a fast, accurate and wide dynamic range 10 MHz – 18 GHz LAN peak power sensor.
-
Product
Automatic Concentration Monitoring
-
ACS is an on-line chemical concentration monitoring system that can provide for keeping an uniform chemical condition by an real time measurement of chemical concentration monitoring in the manufacturing process of display and semiconductor as well as in the control industry of high-quality chemical solution control industry. The close examination and measurement of manufacturing process is an essential to produce an integrated, high quality semiconductor and FPD. The uniform and safety of input chemical on the process of cleaning and etching are directly influence on the product quality.
-
Product
Cable Plant Monitoring
-
Promptlink Communications, Inc.
Cable Plant Monitoring (CPM) is a real-time network device management tool for your DOCSIS network. CPM handles all of your DOCSIS cable modems, Wireless CMs, eMTA and Cable Modem Termination Systems (CMTS) along with monitoring fiber nodes. This allows you to readily see network problems, troubleshoot customer access issues, and easily deal with difficult management efforts, including upgrading CPE firmware on a very large scale.
-
Product
Storage Resource Monitor
-
Storage resource management reporting for health, performance, and capacity of multi-vendor storage
-
Product
Multi Wavelength Monitor
LV5490/LV5480
-
The LV 5490 is a multi waveform monitor that supports 4K video format (4096×2160、3840×2160) based on 3G-SDI dual link or quad link, HD-SDI quad link, and 12G-SDI. The following two 4K video division transmission systems are supported. ・2-SAMPLE INTERLEAVE DIVISION ・SQUARE DIVISION
-
Product
Transformer Monitors
-
The Transformer Advantage is a precision temperature monitor for liquid-immersed power and distribution transformers. It is rugged, fully electronic and field configurable. With Transformer Advantage, users can extend transformer life, utilize maximum capacity and reduce maintenance costs.
-
Product
Monitoring Systems
-
Once a dynamic event is detected, the system instantly informs the control system or other external devices and acts as a digital recorder by capturing important data before and after the event. This information can be used to alert the operator to change process settings or schedule maintenance.
-
Product
Noise Monitoring System
NoiseTutor
-
Continuous monitoring of environmental data in remote areas has always presented a unique set of challenges. Typical solutions involve complex installations, frequent visits to remote locations to keep the system fully operational and require expert level attention to retrieve and share data amongst customers, consultants and project leads.
-
Product
Piezobalance Dust Monitor
3520 Series
-
The Kanomax Piezobalance Dust Monitor 3521/3522 is a unique respirable aerosol monitor, providing direct mass concentration of particulates using PIEZOBALANCE technology; ideal especially for oil mist monitoring. The Kanomax 3521 is equipped with 4 and 10µm impactors while the 3522 is equipped with a 2.5µm impactor. Unlike conventional dust meters, which count particles, a piezobalance dust meter like the 3521 or 3522 “weighs” mass concentration of particulates.
-
Product
SPM Monitor
CS-150
-
The CS-150 is a high-precision chemical concentration monitor designed for use with the SPM solutions used in semiconductor-manufacturing cleaning processes. Featuring fast response and a compact size, the CS-150 continually monitors the concentrations of the various components of the SPM solutions (H2SO4/H2O2/H2O) used to remove metal ions and organic substances. Feedback control based on the monitor output is used to keep the concentrations of the SPM solutions within the allowable ranges and to eliminate unnecessary replacement of chemicals.A short measuring cycle allows the accurate tracking of chemical concentrations, while the compact design facilitates integration with a cleaning device.
-
Product
Hydrofluoric Acid Monitor
CM-200A/210A
-
The CM-200A/210A hydrofluoric acid monitors have been developed specifically to meet the stringent demands of semiconductor manufacturing. The CM-200A/210A provides a real time read-out of hydrofluoric acid concentration by measuring the electric conductivity of the sample solution. These superior units offer high repeatability even at low concentrations. The CM-200A/210A can be used for a variety of purposes ranging from monitoring etched wafer cleaning processes to any other industrial application of hydrofluoric acid.
-
Product
Gamma Air Monitor
Quant Air
-
QuantAir is a solution for measuring radioactive contamination in the air, it provides high-performance detection capabilities with accurate in-field quantification.
-
Product
Advanced Power System - Dynamic DC Power Supply, 20 V, 50 A, 1000 W
N7951A
DC Power Supply
The N7900 Series dynamic DC power supplies are designed for automated test equipment (ATE) applications where high-speed dynamic sourcing and measurement is needed.
-
Product
Advanced Power System - DC Power Supply, 9 V, 200 A, 2000 W
N6970A
DC Power Supply
The N6970A is designed for automated test equipment (ATE) applications where high performance is critical.
-
Product
Ocean Surface Monitor
Current Monitor™
-
sigma S6 Current Monitor™ is a radar-based monitoring system that delivers ocean surface current data from moving stations and both current and bathymetry from fixed locations with high spatial resolution. This greatly improves the management of marine-based activities such as predicting oil slick drift patterns, enhancing navigational safety, and protecting vulnerable coastlines.
-
Product
Branch Circuit Monitor
-
Multiple branches of load can be monitored togetherCan group the device as 3 phase load and single phase loadFaster communication through RS485 port (Modbus protocol)Simultaneous sampling of Volts and AmpsAccuracy Class 1.0 as per IEC 62053-21 & Class 0.5 as per IEC 62053-22 StandardsDisplays more than 25 parameters
-
-
Product
Surface Contamination Monitor
IMI Inspector Alert™ V2
-
The IMI Inspector Alert™ V2 measures alpha, beta, gamma and x-radiation using a 2-inch “pancake” GM detector with high sensitivity to common beta and alpha sources. The easy-to-read digital display shows readings in your choice of µSv/hr, mR/hr, CPM, or CPS. The Total/Timer feature allows timed readings from one minute to 40 hours for precise measurement of low level contamination. An audible alert sounds when the radiation reaches a user-adjustable level.
-
Product
Economical Monitoring Platform
Torque DVMon
-
The DVMon is an economical monitoring platform for digital television networks. Built on the latest compact 1RU hardware, the DVMon raises the bar in user experience through its distinct, flexible HTML5 GUI. Running on any standards-compliant web browser, it allows opening of any number of windows in any size. The DVMon also facilitates opening multiple viewing panels within each window, and eases zooming in or out on any chart axis.
-
Product
Laser Power Meter Monitor
11UNO
-
New 11UNO portable laser power meter brings unprecedented performance in a compact hand-held instrument. The one-finger navigation of the 11UNO laser power meter makes it our most simple to use monitor, and it has just the functions you need to take a fast and precise laser power measurement.
-
Product
Monitor SDR Boards
-
Multiple Access Communications Ltd.
MAC Ltd’s MONITOR product family includes a number of software-configurable digital signal processing platforms intended for use in radio frequency (RF) receiver and transceiver applications. The MONITOR products are available in assembled printed circuit board (PCB) form for integration into larger systems. They also form the basis of MAC Ltd’s CatchAll™ radio products. In addition to the standard products listed below, MAC Ltd is happy to discuss the customisation of existing products and/or the development of new bespoke hardware and software.
-
Product
RF Safety Monitoring
MVG EME Guard XS 6GHz
-
The EME Guard XS is an RF measuring device to alert workers near RF emitters for protection of climbers and other RF-exposed workers. It continuously scans for electromagnetic waves and, via its built-in alarm and visual system, alerts users whenever the acceptable pre-selected limits have been exceeded. This RF Safety PPE is extremely easy to use and supports a safer working environment in the areas of installation and maintenance.
-
Product
Under/Overvoltage Monitors
-
Contacts to control an external horn or light, or to signal your PLC are now available on independent accessories for any power supply. These modules can be used on power supplies with DC voltages from 5 to 125 Vdc. SPDT relay contacts switch if the power supply’s output deviates by:*1.0 volt or more (for 5 volt outputs)*2.0 volts or more (for 6 to 48 volt outputs)*3.0 volts or more (for 49 to 125 volt outputs)
-
Product
Monitoring & Management
Avocent®
-
The Vertiv ™ Avocent® (ADX) ecosystem is a series of IT Management devices and software that provides solutions in edge, enterprise and engineering lab environments. Built upon a secure common architecture the Avocent ADX ecosystem seamlessly integrates and scales to create an open yet resilient IT management fabric.
-
Product
Power, Patchcord, ITA, 72", Micro Power, 12 AWG White, Single Ended (22 Amps)
7-251912000-072
Power Patchcord
Power, Patchcord, ITA, 72", Micro Power, 12 AWG White, Single Ended (22 Amps).
