Pulse Waveform
-
Product
Standard Pulsed Amplifiers
-
An electronic device designed to strengthen short, sharp bursts of electrical or radio-frequency (RF) signals without changing their original wave shape.
-
Product
14-bit, 125 MS/s Waveform Digitizer
ATS9146
-
ATS9146 is a 2-channel, 14-bit, 125 MS/s waveform digitizer capable of storing up to 128 Million samples per channel of acquired data in its on-board memory or streaming acquired data to motherboard memory. ATS9146 is a single-lane PCI Express (PCIe x1) Gen 1 card, which supports up to 200 MB/s bus throughput. ATS9146 is an ideal solution for many applications.
-
Product
High Voltage Pulse Attenuators
-
Barth High Voltage Pulse Attenuators are matched impedance coaxial attenuators for use primarily in pulsed 50 ohm systems, or where occasional transients would damage ordinary units. The attenuator design closely matches the impedance around each resistor, to that resistor. These attenuators feature an input impedance very close to 50 ohms, with characteristics as good or better than most microwave attenuators. These units are ideal for use in nuclear and high energy experiments. Extensive testing during manufacturing insures very high reliability for single-shot experiments. A voltage coefficient of the resistive film of less than .0001 %/V allows low voltage calibration of most systems.
-
Product
Attenuators And Pulse Limiters
-
A bidirectional attenuator, i.e. the attenuation and power capability specification is valid for both directions. There is a large variety of applications for this attenuator: The measuring range of a spectrum analyzer can be increased. Any kind of meter can be protected against overload; it can be used to control the linearity of a meter reading. It can minimize measurement uncertainty caused by mismatched impedances. During an EMI receiver calibration an attenuator directly at the pulse generator output is inevitable.
-
Product
Pulse Magnetic Field Generator
SKS-0902
-
Shanghai Sanki Electronic Industries Co., Ltd.
The technical parameters of the pulsed magnetic field generator SKS-0902 fully comply with the new standards of IEC61000-4-9 and GB/T17626.9; the pulse current output of up to 2000A can meet the needs of different user groups; it adopts a self-developed CNC high-voltage power supply, High precision, high stability, long service life; using self-developed high-voltage electronic switch as the main switch, high stability, smooth output waveform; achieving 0°~359° synchronous phase triggering.
-
Product
PCI-5421, 100 MS/s, 16-Bit Waveform Generator Device
778692-03
Waveform Generator
The PCI‑5421 can generate user-defined, arbitrary waveforms and standard functions, including sine, square, triangle, and ramp. This arbitrary waveform generator can generate signals from -6 V to +6 V and uses direct digital synthesis (DDS) to precisely generate waveforms. The PCI‑5421 also features advanced synchronization and data streaming capabilities.
-
Product
State, Event & Pulse Data Loggers
-
These data loggers can record rates from pulse output transducers, on/off or open close state changes or events.
-
Product
Waveform Amplifier 30 Volts Pk-pk
WA301
-
Extends the output range of function generators30 Volts peak to peak output swingDC to 1MHz bandwidthHigh impedance input, 0dB to +20dB gain50 Ohm and 600 Ohm outputs20dB switchable output attenuatorFully protected output
-
Product
Portable Multi-channel Waveform Monitoring Recorder
MR1200 Series
-
The portable waveform monitoring recorder is a device for recording and analyzing the change process of electrical signal related parameters of the power system.
-
Product
PCI & PXI Waveform Generators
-
Tabor’s PCI/PXI Arbitrary waveform generators are designed to enable a high level of integration, allowing it to implement its unique Arbitrary waveform generation technology in this platform.
-
Product
Autonomous Pulsed Doppler Wind LiDAR System
Galion
-
The Galion LiDAR, distributed by SgurrEnergy, has been optimised for collecting data for wind power applications. The all-sky scanning capability enables many more data collection opportunities than VAD scanning alone.
-
Product
Waveform Generators
-
SIGLENT's function generators / arbitrary waveform generators use advanced Digital Frequency Synthesis (DDS) technology to produce high quality standard function and arbitrary waveform signals. They also provide a wide range of analog and digital modulation functions.
-
Product
Nanosecond Pulsed Lasers
-
Our nanosecond pulsed lasers feature pulses in the ns range. For picosecond and femtosecond lasers please see Ultrafast Lasers.
-
Product
Pulse Air-Gun Ionizers
EC-G Series
-
Panasonic Industrial Devices Sales Company of America
With the new Pulse Air-Gun Ionizer from Panasonic, operators can comfortably neutralize static electricity while manually cleaning. The Pulse Air-Gun’s light-weight, ergonomic design combined with an oil and heat-resistant 2m cable makes it ideal for use at the production line.The Air-Gun Ionizer is equipped with a white LED on the front of the Gun to illuminate target objects. It has three air emission modes: long pulse, short pulse and continuous emission. Ionized air can be emitted at high pressure (range 0.05 to 0.50 MPa), neutralizing static charges and removing dust simultaneously and swiftly.
-
Product
Pulse Laser
-
Is a variable, pulsed high power laser source, a building block ideal for MOPA, LIDAR, OTDR laser systems development and applications. This fully integrated compact module contains a Distributed Feedback (DFB) laser and built-in optical amplifier stage, and a variable nanosecond pulse generation circuits. It provides up to 200 mW optical peak power in 1064 nm wavelength region, with a programmable pulse width from 10 ns to 1000 ns, and a selectable pulse repetition rate from 100 Hz to 1 MHz The optical pulse generation can alternatively be controlled via an external electrical trigger. In a compact design, NPL-CWDM-M is applicable for OEM integration or as a stand alone pulsed laser source. Contact Optilab for more information.
-
Product
Pulse Generators
-
Active Technologies Pulse Generators can be used to set up continuous or triggered pulse streams and offers flexibility to address the most challenging applications like big physics, automated testing, microwaves, modulators, wireless communication, medical and chemistry.
-
Product
Pulse Characterization Sensors
-
Pulse Characterization Sensors provide the ability to see and measure the temporal characteristics of pulsed and CW laser beams. Ophir Fast Photodiode Detectors are designed to convert optical signals into electrical signals which are then measured with third-party instrumentation such as oscilloscopes and spectrum analyzers. Accessories are available to connect to IS6 integrating spheres or fiber optic cables.
-
Product
VXI Precision PLL Waveform Synthesizer
3152B
-
The Racal Instruments™ 3152B Waveform Synthesizer combines 250 MS/s waveform generation performance, versatility, and compact size into a single-slot VXIbus format.The 3152B is a greatly improved version of a fi eld-proven instrument ideal for VXI test stimulus generation. It replaces the 3152A which is standard on many military and commercial test platforms
-
Product
125MS/s PCIBus Arbitrary Waveform Generator
5300
Waveform Generator
Model 5300 is a Single-Channel Arbitrary Waveform / Function Generator that combines many powerful functions in one small package. Supplied free with the instrument is ArbConnection software, which is used for controlling the 5300 and for generating, editing and downloading waveforms from a remote computer.
-
Product
HyMPulse Pulsed Field Magnetometer
-
Metis Instruments & Equipment NV
Geometry independent M-measurement (patent pending): One probe fits all, no pole shoes per magnet geometry. Measure the actual magnet instead of a prepared standard size sample. Measurement of industrial shapes like segments, cylinders, bricks,... with one probe
-
Product
Transient Pulse Generator
8282-1
-
The Model 8282-1 Transient Pulse Generator was designed for screen room use in making conducted spike susceptibility tests. It provides all the waveshapes required by MIL-STD-461B/C and many other military EMI specifications
-
Product
125MS/s PXIBus Arbitrary Waveform Generator
5201
Waveform Generator
Model 5201 is a Single-Channel Arbitrary Waveform / Function Generator that combines many powerful functions in one small package. Supplied free with the instrument is ArbConnection software, which is used for controlling the 5201 and for generating, editing and downloading waveforms from a remote computer.
-
Product
Waveform Function Generators
-
Teledyne Test Tools generate fixed or arbitrarily defined waveforms and signals for use in the development, testing and repair of electronic systems.
-
Product
Pulse Adapter
CV5P350
-
Frothingham Electronics Corporation
The CV5 P350 station is the first mid power pulser in a series of exponential pulse generators that can be connected to an FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of high power exponential pulses. For exponential pulses up to the 10/1000, the CV5 P350 can produce up to 5KW, 500A, or 350V whichever is most limiting. It can also test all of the usual FEC200 tests in the same test program.
-
Product
Isolation Pulse Transmitter
PA-330Z
-
The PA-330Z receives the square wave signals from the rotary encoder, and converts it to low impedance signals suitable for long distance transmission after wave-shaping and amplifying via photo couplers which provide isolation between input and output.A 12VDC external power supply is provided for use with the DC powered RP series encoder.The case is sealed construction which allows closely mounting to the encoder.
-
Product
4-axis Pulse Train Motion Control Modules
HSL-4XMO
Motion Controller
HSL-4XMO is an advanced 4-axis remote motion control module via HSL bus. Combined with HSL I/O and motion control modules, it can meet many requirements in machine automation (MA) field. HSL-4XMO offers two models - HSL-4XMO-CG-N/P and HSL-4XMO-CD-N/P. HSL-4XMO-CG-N/P is suitable for steppers and linear motors. HSL-4XMO-CD-N/P is suitable for servo motors with transfer cable. Except the advanced motion control library (refer to PCI-8164), ADLINK also provides two extra features for users. Motion Point Table Managements can let users assign the points into the module in advance. Then, users can issue command to continuously move the points without consuming CPU resource. Motion Script Download provides users a easy interface to program the application. With this script, the DSP inside HSL-4XMO can decode the file and execute itself.
-
Product
Wireless Pulse Input Transmitter Module
T24-PA
-
The T24-PA transmitter module collects and processes pulse related measurements, such as speed of rotation, proximity, flow and count, forming part of the T24 modular telemetry system. The data transmitted by the T24-PA can be received by multiple T24 receivers that include displays, handheld readers, analogue outputs, relay modules and computer interfaces.
-
Product
SparkFun Pulse Oximeter And Heart Rate Sensor
MAX30101 & MAX32664 (Qwiic)
-
The SparkFun Pulse Oximeter and Heart Rate Sensor is an I2C based biometric sensor, utilizing two chips from Maxim Integrated: the MAX32664 Biometric Sensor Hub and the MAX30101 Pulse Oximetry and Heart Rate Module. While the latter does all the sensing, the former is an incredibly small and fast Cortex M4 processor that handles all of the algorithmic calculations, digital filtering, pressure/position compensation, advanced R-wave detection, and automatic gain control. We've provided a Qwiic connector to easily connect to the I2C data lines but you will also need to connect to two additional lines. This board is very small, measuring at 1in x 0.5in (25.4mm x 12.7mm), which means it will fit nicely on your finger without all the bulk.
-
Product
Pulsed Injection-Locked IMPATT Amplifiers
Pulsed ESR/EPR
-
Insight Product Company offers pulse injection-locked IMPATT amplifiers for pulse ESR/EPR experiments. Pulsed injection-locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate the amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
Product
Pulsed IV
AURIGA 4850
-
Pulsed IV (current-voltage) measurements have emerged as the preferred method of capturing current-voltage characteristics of active devices such as field effect (FETs) and bipolar junction (BJTs) transistors.
