- Virginia Panel Corporation
product
VTAC Wired
VTAC Wired configurations reduce resistance and increase signal integrity with a seamless transition from wire to connector. This can be demonstrated in an example using the results of VPC quality and performance testing on VTAC patchcords. The results are reflected in the graph below. Insertion loss was tested on one-meter long patchcords with SFP+ terminations on either end. The second data line (red) shows the same patchcord, but bisected and terminated with VTAC connectors in its center. The...show more -
product
Multifunctional Safety Tests
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
-
product
Battery Analyzer
KT-97E
● ImpedanceRange: 6mΩ / 60mΩ / 600m Ω / 6Ω (auto-range)Accuracy: ±1.5% of reading ±3digits Resolution: 0.001mΩ● CapacityRange: 0 ~ 9999Ah Accuracy: ±1.5% of reading ±3digits Resolution: 0.001Ah● DCV Range: 6V / 60V (auto-range) Accuracy: ±0.5% of reading ±3digits Resolution: 0.001V● DCARange: 6A / 60A / 200A (manual) Accuracy: ±1.5% of reading ±3digits Resolution: 0.001A / 0.01A / 0.1A● Temperature Range: -20℃~100℃Accuracy: ±1.0℃ Resolution: 0.1 ℃ ● Set discharge end voltage manually.● Auto alar...show more -
product
Install and Development
Whether it is an error proofing application or a complete end-of-line (EOL) test solution, ARC services what we sell by providing quality onsite installation and development as required by the project. Whether it is a senior engineering resource or our expert team of engineering technicians, ARC can provide the best solution to get your application up and running at your site when completed.
-
product
Data Acquisition Processor Board
DAP 5200a
The DAP 5200a model brings many more real-time data acquisition and control applications within the scope of Windows systems. Its onboard 400 MHz processor substantially increases the real-time processing power of the top end of the DAP line. Real-time processing functions include smoothing, filtering, FFT, PID control, and responding to alarm conditions;
-
product
Rugged Amplifiers And Transmitters
Communications & Power Industries
CPI TMD began developing power supplies at the end on the 1980s, expanding its amplifier product line. By leveraging this expertise together with its proficiency in microwave tubes and the complexities of integration, CPI TMD has build a thriving amplifier and transmitter business to serve the needs of its defence and communications customers.
-
product
Digital I/O Board, 32 Isolated I/O Channels, 24V +special EEPROM & TTL IO Port
APCI-1500-PULS
PCI interface to the 32-bit data bus Connector compatible to PA 1500 Connector and software compatible to CPCI-1500 16 isolated input channels, 24 V, including 14 interruptible 3 software-programmable counters/ timers 16 isolated output channels, 10 to 36 V, output current 500 mA Timer-programmable watchdog for the reset of the outputs"-PULS" version has a special EEPROM and a TTL IO port added at end of cardDiagnostic report through status register in case of short-circuit, overtemperature, voltage drop or watchdog Interrupt triggered through watchdog, timer, error One ground line for all inputs and one ground line for all outputs
-
product
Automated Test Handler
In-Line Duomax
100 % Automated Fixture Change1.5 N x 8000 Test PointsICT FCT EOL IntegrationHigh ProductivityHigh QualityGreat ROINo PLC
-
product
Loop A Line
TX916
The Loop a Line has been a Telstra standard for 20 years. It is probably the simplest time saving device available for contractors and technicians. Once fitted to the far end of a line you can switch between Open, Short, Connect, 600 ohm, and Tone modes allowing all installation and fault location to be performed from the one end without having to go back and forward from one end of the line to the other.
-
product
Series and EOL Testing of Electric Motors
Highly automated EOL test system for blind motors*Test station with fully automatic mechanical and electrical contacting *Scanning the product coding with barcode scanner*Integrated label printing, additional error printer*Contact protection by light curtain
-
product
Fast LID Measurements for EOL
KMP
TechnoTeam Bildverarbeitung GmbH
The KMP is the solution to cost-effectively bring indirect light measurement technology to places with too little space for a BV room. Its lightweight and compact design allow it to be integrated into production lines, positioned next to production or in a small lighting lab.
-
product
Fiber Optics
The most complete line of Fiber Optic Products for end-to-end AV signal distribution over fiber optic cabling.
-
product
Cycle-ATV Dynamometers
EC997
The EC997 Series, our standard eddy current motorcycle chassis dynamometer, takes motorcycle performance tuning to the next level. The EC997 Series uses the industry’s most advanced electronics and Dynamic Load Control technology, featuring precision closed-loop torque feedback – a standard feature with every EC997 dyno. Competitor’s dynos on the market allow you to apply “percent % load” but Mustang has perfected the art and science of Dynamic Load Control and proudly offer the most sophisticat...show more -
product
CorEdge Box PC's
The CorEdge line of Box PCs were designed with “Edge Computing” in mind. Corvalent’s edge computing solutions cover a wide range of technologies built to solve problems in mission-critical industrial environments. CorEdge Box PCs support the infrastructure that exists close to the sources of data through expandable IoT embedded systems.Corvalent’s CorBox family is a full line of innovative, x86 processor based systems, providing the latest Intel microprocessor technology. The CorBox family of In...show more -
product
End of Line Noise Test System
End of Line Noise Test Systems from VIacoustics are designed to support end of line product noise testing on factory floors and quality assurance environments. Using the Limit Analysis features of the Nelson Acoustic Trident software, users can set noise emission maximum, minimum or control range criteria based on Awtd and/or 1/N octave band criteria. Criteria can be customized for most any type of product based on the noise emissions of known good and bad units. The large front panel Pass/Fail indicator allows operators to quickly determine if units meet the criteria. Data on units that fail can be exported for further analysis.
-
product
Motion Reference Units And Wave Sensors
MRU And WS
The Motion Reference Unit (MRU) product line was first released in 2004 when Inertial Labs MEMS-based sensor solutions began to compete in performance with traditional FOG units. Easy integration of the MRU product line for the end user means competitive performance at no extra cost.
-
product
Crypto Devices
Confidential communications are essential to armed forces and government authorities. The Rohde & Schwarz crypto devices provide secure end-to-end encryption for the secure transmission of sensitive information over public communications networks or radio transmissions. Rohde & Schwarz crypto devices are interoperable with HF/VHF/UHF radios, satellite communications and line transmission equipment. They can encrypt and decrypt voice and data communications at the highest security levels. The crypto devices are ideal for stationary and mobile platforms in rugged terrain and in naval and airborne environments.
-
product
Multi-Purpose Probes
*For All your Functional Test Needs *Machine Building *end of line test
-
product
Flightline Pilot Static Test Set
ADTS-3350 Series
TestVonics™ ADTS-3350 Series Test Set is a portable, high precision, dual channel pitot static test system. This tester is designed to calibrate, test and troubleshoot air data instrumentation and aircraft pitot-static systems. The test set has been designed with functional and reliability features highly suited to withstand the harsh environmental and demanding conditions of the flight line environment, especially for military end users. The test set is designed for testing a wide range of comm...show more -
product
Graphical Power Quality Analyzer
PS5000
The PowerSight PS5000 Power Quality Analyzer is the premier member of the PowerSight line of compact, versatile, easy-to-use power quality analyzers. It provides the Most Efficient and Error Free Solution for doing Power Studies.The full color display eliminates the need for laptops to see waveforms and logs. Phasor diagrams provide quick verification of connections.The visual presentation of potential errors in connections and settings, via SureStart, minimizes the risk that the data will be incorrect at the end of the study.The graphical user interface allows easy changing of trigger thresholds.The large screen and “soft keys” allow quickly viewing all measurements of interest quickly.
-
product
Sound Harmonics and Current Analyzer
H74050100
This analyzer is used as end of line control for electro mechanic components with electric motors, with or without mechanical reduction. While the motor is running at nominal speed, a spectrum and temporal analysis of the sound as well as a current consumption test is performed. Statistical analysis of the data acquired is also performed real-time, expediting the PASS/FAIL decision of the DUT.
-
-
product
In-situ Wafer Temperature Monitoring
CI Semi's family of noncontact temperature monitors (the NTM line), offers high end pyrometry products for the measurement of wafer temperatures during process. CI Semi’s flag ship of the line, the NTM Delta, incorporates real-time, same point emissivity measurement and compensation making it the ideal solution for in situ monitoring for processes such as RTP, CVD and PVD. The NTM family is sold to leading tool manufacturers.
-
product
Digital Melting Point Apparatus
DRK8011
Shandong Drick Instruments Co., Ltd.
DRK8011 Digital melting point apparatus is fully in line with ‘humanize’ of the design concept, using photoelectric automatic detection, dot matrix image LCD technology, digital keyboard input, each measuring one sample, measure three times the average of the melting point of the automatic strike, and has a melting, melting end automatically, melting curve automatic recording function. Temperature system uses high inearity make platinum resistance sensing element, the use of PID regulationtechno...show more -
product
EOL Tester
Sterner Automation would like to introduce its new end of line (EOL) tester platform. Sterner Automation has been a supplier of calibration and test equipment to the automotive industry for over a decade and is now offering a standard hardware EOL platform that is configurable with a variety of software modules for seating plant applications.
-
product
BottleChek
The BottleChek Metal Detector Conveyor is designed to inspect pharmaceutical bottles or vials at the end of the packaging line for unwanted metallic particles. The system easily integrates into any production line for side-by-side transfers.
-
product
LXI WTB Terminator, 90.6 ohm
60-983-002
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
product
Product Testing And End Of Line
World-class integration of electronic test equipment, instrumentation, test fixtures, automation, load simulation,data acquisition, and software . In partnership with two major leaders in high-technology automation, three very capable machine shops, a custom cabling company, a rapid prototype circuit board fabrication house and two large automated sheet metal manufacturing facilities we offer custom process and test equipment designed and manufactured for convenience and precision. Each component of our systems is carefully consideredto provide you with maximum performance consistent with easy maintainability and long term return on your investment.
-
product
Acoustic Test Chambers
Small Device Test Chambers are used for >Basic sound level measurement of small products and equipment >Pre-compliance testing of small products and equipment >End of line manufacturing test on small products and equipment Small Device Test Chambers provide acoustic isolation from outside sounds and/or reduce the sounds from the device under test radiating into the host
