Voltage Interruption
-
Product
Meters for Current & Voltage
EE301-DCM-xx
-
LCD Current Readings:0-80.0 / 40.0 / 20.0. LCD Voltage Readings:0-50.0 / 150.0
-
Product
PC Controlled High Voltage Tester
Cablescan H8
-
The Cablescan H8 provide the PC-based power of the larger PC based testers, but in an economical package for users who do not require more than 512 test points. This analyzer is designed to operate under the control of your PC.
-
Product
Low Voltage Container Load Banks
-
Guangdong EMAX Electrical Co., Ltd.
Container load banks are portable, self-contained solutions for testing and maintaining large power systems, designed to be easily transported and deployed in a variety of environments, making them ideal for both temporary and permanent installations.
-
Product
High Voltage Amplifier
HA-400
-
*400Vp-p(±200V DC) *160mAp-p(±80mA DC) *Bandwidth: ≦600KHz(200Vp-p) *Slew Rate: 300V/us *Gain(AMPL): 0~90(10 Turn VR) *DC Offset: ≦0~±200V (10 Turn VR + SW) *Output Resistor: 50Ω
-
Product
Clamping Voltage Tester
MIG0603CLV2
-
The MIG0603CLV2 is a generator for clamping voltage testing of varistors. It has circuits with four different source impedances and up to 15 different measurement ranges. The instrument is used to perform varistor clamping voltage tests on up to 1000 V varistor types. The test impulse is a 8/20µs current waveform up to 500A which is maintained over the entire load range.
-
Product
Continuity of Insulation Tester (Low Voltage Method)
DYQ-005
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-5;Inspection standard: JB/T4279.12-2008Used to test the film continuity (namely the pinhole number of enamelled wire sample per unit length) of enameled round wires with nominal conductor diameter of0.050mmand below;The application of advanced SCM control allows for faster operation and stronger anti-interference capacity.
-
Product
Relay Testing Voltage Source
PTE-FCN
-
It is the easiest and most economical way of increasing the relay types that can be tested with the PTE-100-C. The PTE-FCN includes its own LCD display and a BUS-PTE connection, which makes it easier to operate and enables it for use in combination with any other test set in the PTE range. The PTE-FCN is included as standard in models PTE-100-C Pro and PTE-50-CE Pro.
-
Product
High Voltage Amplifier
HA-800
-
*800Vp-p(±400V DC) *70mAp-p(±35mA DC) *Bandwidth: ≦200KHz(400Vp-p) *Slew Rate: 200V/us *Gain(AMPL): 0~180(10 Turn VR) *DC Offset: ≦0~±400V (10 Turn VR + SW) *Output Resistor: 100*Ω
-
Product
120-600V Solenoid Voltage&Continuity Tester
1867
-
Peaceful Thriving Enterprise Co Ltd
Test voltage from 120-600V AC/DC polarity and continuity.
-
Product
LXI High Voltage Switching - 20xSPST Plugin Module
65-233-703-HI
General Purpose Relay Module
The 65-233-703-HI plug-in module is part of a scalable high voltage switch platform that provides a high voltage switching solution with capability up to 7 kV. Switch arrays are created by populating the 65-200-002 scalable chassis with plug-in modules that provide access to the switches on 51-pin front panel connectors. Users can specify as many or as few plug-in modules as they require and can field upgrade the chassis to extend the number of switches.
-
Product
LXI High Voltage Switching - 20xSPST Plugin Module
65-233-903
General Purpose Relay Module
The 65-233-903 plug-in module is part of a scalable high voltage switch platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
High Voltage Film Capacitor
STHVP/STHVE
-
High Voltage Pulse Current for medium frequency applicationHigh Voltage DC / AC Voltage applicationCapacitor can be discharged at rated voltage directly without any protective component and with ambient Temperature up to +105CHigh Voltage Decoupling and SnubberingVoltage MultiplierInduction heatingAct as discharge capacitor to trigger laser, X-Ray and Tesla CoilFor high voltage capacitor bank or arrayHigh Voltage Power Supplies
-
Product
AC/DC Withstand Voltage Test
WB2671A/WB2671B
-
• Output voltage: 0-5kV (AC/DC); • Cutoff current range: AC 0~20mA (WB2671A)/0~100mA (WB2671B); DC 0-20mA; • Test time: 1-60s; • Transformer capacity: 750VA.
-
Product
PXI 6x4 High Voltage Power Matrix
40-332-002
Matrix Switch Module
Designed for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VDC peak cold switching and 110VDC/250VAC hot switching. This range is available in 12x2 or 6x4(shown here)matrix configurations. Connections are made via a front panel mounted 37 pin high voltage D-Type connector.
-
Product
PXI/PXIe High Voltage Multiplexer, Dual 23-Channel, 2-Pole
42-321-128-HI
Multiplexer Module
The 40-321-128-HI (PXI) and 42-321-128-HI (PXIe) are dual 23-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
Low Voltage Differential Oscilloscope Probes
-
Differential signaling used in high speed serial standards requires very accurate characterization. The industry-leading bandwidth and signal fidelity found in a Tektronix low voltage differential oscilloscope probe ensures that you see every possible detail. Tektronix offers TriMode™ architecture which streamlines measurement acquisition by enabling you to make differential, single-ended, and common mode measurements with a single connection!
-
Product
Process Voltage & Current Data Loggers
-
Monitor and log virtually any process voltage or current output from your transducers.
-
Product
High Voltage Differential Probe
DP750-100
-
Shenzhen Micsig Instruments Co., Ltd.
*The leads and probe are with shielded design, interface ends are integrated in a compact box, no need to twist the cables, leads to a lower noise floor and has less interference. *Support one-press Zero calibration and automatic overrange alarm.*Directly powered by Micsig UPI interface, realise auto scaling setup, can also powered by oscilloscope via USB cable.
-
Product
Voltage And Current Amplifier
KINGSINE KA30 / KA60
-
KINGSINE Electric Automation Co., Ltd.
KINGSINE's KA30 / KA60 voltage and current amplifier is high accuracy, high power, Panel-mounted type real time simulation power amplifier with four-phase voltage and three-phase current.
-
Product
PXI/PXIe High Voltage Multiplexer, Single 23-Channel, 2-Pole
40-321-127-HI
Multiplexer Module
The 40-321-127-HI (PXI) and 42-321-127-HI (PXIe) are single 23-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
100-600V AC Non-Contact Electric Voltage Detector With Buzzer
1969
-
Peaceful Thriving Enterprise Co Ltd
*With cUL and RoHS Approval.*Check voltage on 100-600V AC.*Two LR44, 1.5V batteries which is included.*Audible and visual indication for easy operation.*Four-section power and sensitivity switch (H, L, M and off).*Locates breaks along live, insulated wires and power cords.
-
-
Product
DC Voltage Generator
MON8P
-
Mezzanine MON8P is designed to generate DC voltage in the range of ± 10 V through eight galvanically isolated channels from each other and from the case, which allows to reduce the level of interference and increase the safety of the device.
-
Product
High Voltage Dry Reed Relays For up to 10kV
Series 67 & 68
-
Series 67 PCB mounting with switch and coil connections in a Single-in-Line format.Series 68 PCB connections on the underside for coil connections. Flying leads from the top face for high voltage connections.The Series 67 and 68 are constructed using former-less coils. The absence of a coil supporting bobbin allows a device smaller than the industry norm. The unusual package design gives some interesting possibilities for high density packing.The option of flying leads for the high voltage connections makes it possible to keep this away from lower voltage circuitry on the pcb.Form A (energize to make) contacts are available with the option of 5, 12 and 24 volt operating coils.
-
Product
Voltage and Current Measuring Technology
-
HIGHVOLT Prüftechnik Dresden GmbH
Designed for the measurement of alternating current (AC), direct current (DC), lightning (LI) and switching (SI) impulse high voltages (HV) as well as AC and impulse high current (HC) according to IEC 60060, IEC 61083 and IEC 60052, available as indoor and outdoor design.
-
Product
Voltage Pulse Generator
LSG-65C
-
Shanghai Sanki Electronic Industries Co., Ltd.
The waveform parameters of the voltage pulse generator LSG-65C fully meet the requirements of IEC60065 and GB8898; the pulse voltage output of up to 10kV can meet the requirements of different test levels of users; the self-developed high-voltage electronic switch is adopted , which has high stability, low noise and long service life. Long; digital display mode, intuitive and easy to operate.
-
Product
Ultra High Voltage DC Power Supply
-
Output control can be switched between remote control and local control. The output display and output indicators are located directly on the front panel and can be directed to an external remote display. The high voltage output terminal has overcurrent, overvoltage, short circuit protection and arc protection.
-
Product
Voltage Indicator
-
Small installation devices for measuring both alternating and direct voltages.
-
Product
Safety Voltage Detector
325 SVD
-
Standard Electric Works Co., Ltd
● Compact, easy to wear and convenient in use● Designed for indoor and outdoor use● Water-proof design. (IP65)● Equipped with self-testing functions● Able to sense all kinds of AC High Voltage System● Low power consumption● CE Certifiedright LED visual indication
-
Product
Dual Voltage Buffer with Current Drive
BUF-01
-
The BUF-01 Voltage Buffer is a dual channel buffer capable of driving up to 50 mA of current on each channel at up to ±10 V output. The buffer has a 2nd order low pass filter with 3 dB point of 119 kHz to remove high frequency noise. The unit’s differential inputs are built to withstand high DC over-voltages up to ±50 VDC and greater than ±100 V transients. Gain of the unit is 1 allowing for minimal insertion issues.
