Limiters
-
Product
Building Vibration Software Module
-
Metra Meß- und Frequenztechnik Radebeul GmbH & Co. KG
*Measurement and evaluation of vibrations in buildings to DIN 4150-3 for the determination of their effects on structures*Convenient user guidance requires only short training*Comparison with limiting values to DIN 4150-3*Simple generation of reports*Detection of the main frequency*Recording of vibration events and real-time signals*External Messengers*Offline measurement*Available as kit: VM-STRUC Kit with accelerometer KS823B
-
Product
Repeat Durability Tester
TIQ1000
-
It is a device to measure repeated endurance such as limit bending test of board, endurance test of mounted board, endurance test of connector, etc. Continuity data and load data can be obtained during the cyclic endurance test. Conforms to JEITA ET-7407 "Environmental and durability test methods for mounted CSP/BGA packages".
-
Product
4/5 Pin Trailer Harness Checker / Towing Maintenance Kit
#8026
-
Innovative Products of America
Test, clean and restore 4/5 pin trailer connections. Tester will verify tow vehicle is sending proper signal to the connector, while cleaning tool removes corrosion and verifies proper pin size on both male and female truck/trailer plugs. For use with 4/5 flat connectors. Patented. Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardsKit Includes: #7866: 4/5 Pin Trailer Harness Checker, #8021: 4/5 Pin Cleaner, and #8030: 2 ml DeoxIT Cleaner
-
Product
XLR Barrel Version of the same Switchable Soft-Clip Limiter
Over-Killer
-
An Over-Killer is an XLR barrel version of the same switchable soft-clip limiter found on our revered audio interfaces. Designed to get more out of your digital copy by allowing you to push levels while limiting the level of a balanced analogue signal to +18dBu.
-
Product
BACnet / Modbus
-
BACnet™ MS/TP and Modbus RTU communicating sensors provide an easy-to-install and cost-effective means to measure temperature and humidity anywhere on your network. They’re especially effective where there is limited controller inputs or the application is for monitoring only. All BACnet™ sensors are BTL Certified.
-
Product
Wire Crimp Pull Tester (Motorized)
WT3-201M
-
The WT3-201M motorized wire crimp pull tester is designed to measure pull-off forces of up to 200 lbF [1 kN] for wire and tube terminations. The tester conforms to numerous UL, ISO, ASTM, SAE, MIL, and other requirements for destructive testing. Non-destructive testing is also possible, such as pulling to a load or maintaining a load for a specified period of time, as per the requirements of UL 486A/B. Programmable pass/fail limits with red and green indicators and audio alerts help identify non-conforming samples.
-
Product
Power Line Meter
-
The Line EMI Meter measures electromagnetic interference in a single-phase AC power line. It plugs into a wall outlet (mains socket) and requires no battery. It immediately displays total line noise in millivolts (range 1999 mV, resolution 1 mV) in the frequency range 10 KHz 10 MHz (the frequency limits at which sensitivity is of the maximum sensitivity). A speaker plays the sound of the EMI, amplitude demodulated, in order to identify the EMI source (such as an AM or shortwave radio station vs. a motor vs. an electric arc).
-
Product
Online Conductivity Controller
LD-LOCC-A10
-
Online Conductivity ControllerLD-LOCC-A10features 3 points conductivity calibration system, TDS measurement mode, and 4 to 20 mA output signal transmitter. The large and clear back light LCD displays Calibration and setup values, Temperature values, ATC (automatic temperature compensation) values, high and low limit of measurement. This controller measures Conductivity and TDS values in µS/ cm, and mS/ cm units.
-
Product
Absolute Length Gauges For Measuring Stations And Multi-gauging Fixtures
ACANTO series
-
*High system accuracy: ±2 µm / ±1 µm*Serial data transmission*Interface: EnDat 2.2*Protection rating of up to IP67*Compact design for limited installation space*Various plunger actuation possibilities
-
Product
MultiGas™ TFS™ Gas Monitor For Multi-Compound Gas Analysis
-
The MultiGas™ TFS™ Monitor is an online, multi-compound, trace gas monitoring system in a stand-alone 19-inch rack enclosure. It uses an innovative tunable filter spectroscopy technology enabling high selectivity and stability measurement. Low detection limit (sub-ppm levels for most gases) is achieved through the use of high throughput optics coupled with a long-path gas cell and a high sensitivity detector.
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting Holes
LBC SERIES
-
The LBC Series (Load Button) load cells are offered for compression only applications where space is limited. The matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Counter bored mounting holes are provided for fastening down from the top. These sensors are manufactured from heat treated 17-4ph stainless steel and sealed for use in most industrial environments.
-
Product
Harness Design and Manufacture
-
When designing an underwater cable harness, there are some factors which need to be considered, and we have produced the following list as a guide for customer information:Component considerations:- Electrical requirements- Mechanical considerations- Quality requirements- Reliability- Design redundancy (contact count)- Connector selection (type and form)- Locking requirements- Backpotting requirements- Waterblocking in moldings- Cable specification- Cable jacket material and compatibility with elastomers- Abrasion resistance- Stiffness profile at termination- Connector format (straight or right angle)- Molding format (straight or at an angle)- Clearance allowance for molding and cable routing- Elastomer compatibility (eg oil filled units)- Metalwork selection re: corrosion and cathodic delamination- Surface finish for metalwork as appropriateOperational considerations:- Operating depth profile (not just max. depth)- Tensile loads- Torsional loads- Bending loads- Bend control requirements (to limit bending at termination)- Deployment and recovery loads- Dynamic loading-Flow turbulence effects.
-
Product
PCI Smart Bus Extenders
Live Insertion PCI Bus Extenders
-
The Ultraview PCIEXT64 extender series offers excellent PCI signal integrity, due to high speed trace layout, including high impedance signal traces and minimal ground inductance, as well as active bus isolation, to ensure minimal effect on the board-under-test. Power monitoring and current limiting features allow a robust debug and test environment. The capabilities of Ultraview's two models of Universal 66/33MHz 64/32-bit PCI extenders are as follows:
-
Product
Battery Chargers
BAC Series
-
Battery charger BAC series is a portable and universal battery charging solution. It is primarily intended for charging Lead-Acid, Ni-Cd and Li-ion batteries from 1 V DC to 300V DC level. However, the unit can charge the string of any battery type by one of the available charge modes:IU (constant current + constant voltage)UU (constant voltage + constant voltage with a current limit)Charging modes provide a safe regulation of charging procedure and achieves fast recharge and low risk of overcharge.Variety of implemented protections, such as thermal, overcurrent, undervoltage, and overvoltage, assure the charging process will be safe for the battery and the instrument itself.A user doesn’t have to switch off the main charger in order to use BAC series charger. Just the opposite, the BAC series charger should support the main charger to speed up the process. An alternative use is to quickly recharge a battery following a discharge test.The provided display enables users to monitor all relevant information during the charging process and to adjust charging parameters and limits in real-time.The instrument offers the best power-to-weight ratio in the market, weighing only 10 kg / 22 lbs with the maximum output power of 2,7 kW.The maximum charging currents for lead-acid, Ni-Cd and Li-ion batteries, at various battery voltages, are presented in the brochure.
-
Product
CAM/TRAC Test Kits
Series 41
-
The Series 41 dual well mechanical kits provide a test solution where Z axis and the testing of two PCA’s is required. These can be similar devices, or devices that are used together in a functional test. The Series 41 Kits have the same available features and options as the Series 40 Kits. (Limited sizes available.)
-
Product
Limit Controllers
-
Limit Controllers shut down power to heating and cooling circuits in the event of an out-of-range hot or cold condition. Disables a redundant coolant valve to protect against primary coolant valve failure. Easily read and set by the user. The large LED display indicates temperature and system status.
-
Product
Calibrator, 0 to 24 mA, Current, 185 mm, 78 mm, 38 mm, ± 0.5%, 265 g
72-6694
-
*Adjustable 0 to 24 mA current source*Current calibrator drives loads up to 500 Ω*Large LCD display*Sampling Time : Approximately 0.4 seconds*Over Input Indicator : 1*Operating Temperature : 0°C to 50°C ( 32°F to 122°F)*Size : 185 × 78 × 38 mm (7.3 × 3 × 1.5 inches)*Weight : 265 g (0.58 lb) including battery*Requires one 9 V battery - not included*12 month limited warranty *view Terms & Conditions for details
-
Product
FMC Mezzanine Module, 4 or 8 Channel
NES-FMCSER
-
Sundance Multiprocessor Technology Ltd.
The FMC specification was developed to enable FMCs to be supported on a wide range of existing form factors including but not limited to, PCIe, VME, CompactPCI, VXS, VPX, VPX-REDI, AdvanceTCA and AMC. Up to three FMCs can be fitted on a 6U VPX carrier.
-
Product
Nano Spotter For MALDI-TOF MS
AccuSpot
-
Bringing LC to MALDI Technology LC/MS/MS is often regarded as the technique of choice in identifying components from complex mixtures; however, it is not without its limitations. An alternative approach is to consider LC/MALDI.
-
Product
Retractable Sources
-
Veeco’s retractable sources address fundamental limitations of MBE, including source capacity, source removal for maintenance and system uptime. The retractable source allows an individual source to be withdrawn and isolated from the growth environment with the source gate valve and then removed without venting the entire chamber.
-
Product
Switch Path Manager Lite License - SPM Lite
90-900-901
-
A low-cost "lite" version of our Switch Path Manager has a site license (can be used on unlimited PCs) and a boot limitation of two switching modules.
-
Product
Arresters
-
Next to your people, your power grid infrastructure is your largest and most valuable investment. Protect it with Hubbell Power Systems, Inc. surge arresters. Every lightning strike, insulator flashover and switching surge adds wear and tear to your equipment, prematurely aging it, and requiring you to shoulder the costs of replacement. Even the smallest surge can shorten your equipment’s life. Surge arresters, however, extend the life of your system by limiting the voltage across your equipment during a surge event.
-
Product
Power Supply
EXC-PSM104P85S
-
The EXC-PSM104P85S is an isolated DC power supply specifically designed to provide reliable power for highly demanding PC104-Plus imbedded applications. The EXC-PSM104P85S has a wide input voltage range while providing robust and reliable power for embedded and industrial motherboards. The power supply is also fully compliant with MIL-STD-704A and E, MIL-STD-1275B and MIL-STD-461E.The EXC- PSM104P85S has totally independent safety features including input undervoltage lock-out, output overvoltage protection, output current limit protection, and temperature protection. Additionally, the Soft-Start function limits inrush current during startup.
-
Product
Condensation Chamber
-
Wewon Environmental Chambers Co, Ltd.
The condensation test chamber does not need special installation conditions, just need to connect to the ordinary power supply and running water can be used normally. The functional diversity of the equipment, fast and low operating costs make the machine a very high cost performance condensation testing machine in the market. The machine can be programmed to control three different test effects: Humidification, natural cooling and drying, and the corresponding temperature and running time of each test, and set the total time of program running and the number of cycles. The condensation tester has an automatic water replenishing device. When the water temperature exceeds the upper limit, there will be a protection device for safety warning, and it is very safe to use.https://www.wewontech.com/condensation-chamber/
-
Product
Gage EXpert FPGA Realtime Data Streaming
eXpert Stream-to-Analysis
-
All Gage PCI Express CompuScopes are able to Stream waveform data through the PCI Express bus directly to PC RAM. By contrast, older Memory Mode operation required storage of data in dedicated digitizer memory prior to data transfer. Streaming provides two distinct advantages over Memory Mode. First, Streaming may overcome the acquisition time limit imposed by the volume of dedicated digitizer memory. Second, in Streaming Mode, the user does not need to await completion of waveform acquisition before accessing the resulting waveform data, which is necessary in Memory Mode.
-
Product
Gauge Type T Thermocouple Wire
W-TW-40P2
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
PCI Smart Bus Extenders
PCIEXT-64U - Live Insertion PCI Bus Extender
-
The Ultraview PCIEXT64 extender series offers excellent PCI signal integrity, due to high speed trace layout, including high impedance signal traces and minimal ground inductance, as well as active bus isolation, to ensure minimal effect on the board-under-test. Power monitoring and current limiting features allow a robust debug and test environment.
-
Product
Miniature Axial Extensometers
Model 3442
-
Jinan Testing Equipment IE Corporation
Weighing as little as 8 grams, these miniature extensometers are designed to have very low operating force with minimal specimen influence. All use an improved version of Epsilon’s dual flexure design which makes them very rugged for their size. With a module height of 15.2 mm (0.6 inches), they will fit in the limited space between grips that is typical with small test samples. Gauge lengths can be as short as 3 mm or as long as 50 mm. A newly designed gage setting pin and assembly allows the gauge length to be set accurately and repeatably to ASTM and ISO requirements for all gauge lengths. Reengineered quick attach wire forms provide simple and secure specimen attachment. Wire forms for round and flat specimens are included, as well as flat, 3-point, and vee knife edges. The wire forms may be removed to enable mounting using elastic bands or springs. A tethering attachment point provides fall protection and enables counterbalancing of the extensometer’s weight when testing delicate specimens.Model 3442 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller and Epsilon will equip the extensometer with a compatible connector wired to plug directly into the controller. For systems lacking the required electronics, Epsilon can provide a variety of solutions for signal conditioning and connection to data acquisition systems, chart recorders, or other equipment.
-
Product
Rotary Limit Switch
-
AMETEK Sensors, Test & Calibration
When motion is expressed in shaft rotation, we can provide limits that are adjustable throughout the entire range of movement. Rotary limit switches can be used for material handling on crane or winch drums, hoists, lifts, screw jacks, or platforms.
-
Product
100GbE Application and Security Load Module
PerfectStorm 100GE 1-Port Load Module
-
Keysight Network Applications and Security
PerfectStorm is a highly modular hardware test platform enabling equipment providers, service providers and enterprises the ability to create real-world, high-stress conditions and user behavior to push new equipment and networks to their limits.
