Mainframes
Fully capable housing with power, cooling and emi protection ready to operate with the addition of instruments.
-
Product
Switch Mainframe
SW1002
-
Switch between voltmeter and battery tester while testing. 264 channels max. (2-wire) to 72 channels max. (4-terminal pair). Circuit design friendly for impedance measurements that minimize errors between channels (Effect: 0.01% f.s.*). For BT4560 100 mΩ range, R measurements, and a measurement frequency of 1 kHz. For OCV measurement, internal resistance measurement, and external potential measurement of battery cells. Measure battery modules up to 60 V DC.
-
Product
150 Watt Electronic Load Module
N3302A
-
The Keysight N3302A is a 150 W (0-30A, 0-60V) electronic load module for use in either the N3300A or N3301A electronic load mainframe in system applications. The N3302A load module is fast and accurate, for programming in constant current, constant voltage, or constant resistance modes, or for making voltage, current or power measurements. The N3302A can also digitize waveforms.
-
Product
Electronic Load Mainframe GPIB
3300 Series
-
A 4 Channels 1200W Mainframe which accepts up to four Load Module.
-
Product
Modular System Power Supplies
N6700 Series
-
The N6705A is 4-slot mainframe that accepts 1 to 4 modules in any combination. Modules are ordered separately. Maximum output power is 600W. The DC Power Analyzer is designed for bench testing in R&D. It is a highly integrated instrument that combines up to four advanced DC power supplies, DMM, oscilloscope, arbitrary waveform generator and datalogger. It provides an easy-to-use interface, with all sourcing and measuring functions available from the front panel.
-
Product
RF & Microwave Modules for 34980A
-
The Keysight RF and Microwave multiplexer modules for the 34980A Multifunction Switch/Measure Unit offer broadband switching capabilities for switching from DC to 26.5 GHz. Use these modules to route test signals between your device under test and your signal generator, oscilloscope, spectrum analyzer, or other instrumentation. A switch/attenuator driver module also allows control of switches and attenuators external to the 34980A Mainframe.
-
Product
Instrument Mainframe
PI-11006
-
The PI-11006 Instrument Chassis was designed to accommodate the power and noise requirements of some of Pulse Instruments analog instrument cards. These instrument cards, such as the PI-41401, PI-41702 and others supply signal outputs that require more current from the -12 V supply than available in a standard chassis. Therefore this chassis has a larger -12 V power supply that provides 2.5 Amps.
-
Product
Breadboard Module for 34980A
34959A
-
The Keysight 34959A module for the 34980A Multifunction Switch/Measure Unit can be used to create custom designs inside the Mainframe. You can control your circuits with access to both the +12V and +5V supplies, 16 GPIO ports, and 32 relay drive lines. The faceplate has cutouts for the most common connectors. The breadboard module can be programmed using standard read and write commands in SCPI.
-
Product
T3AWG2K Series - 16-bit Dual Channel Arbitrary Waveform Generator
T3AWG2K Series
-
The T3AWG2K series consists of two affordable dual-channel arbitrary waveform generators, 16-bit vertical resolution, 6 Vpp output voltage (50Ω to 50Ω), 128 Mpts/ch memory, a maximum sampling rate of 600 MS/s and a maximum sine wave frequency of 150 MHz. The T3AWG2152-D mainframe adds 8 synchronized digital channels to the analog outputs, ideal for debugging and digital design validation.
-
Product
Rack Mount Kit For CX3300 Series
CX1903A
-
The Keysight CX1903A rack mount kit for the CX3300 series lets you easily stack your CX3300 mainframe in a rack.
-
Product
3-Slot Data Acquisition Mainframe With GPIB, Two 20-Channel Switch Modules, One 20-Channel Multiplexer Module, And BenchVue DAQ Software
DAQ973SBX
-
The DAQ973MBX best multiplexer bundle offer includes a DAQ973A single 3-slot data acquisition mainframe (USB, LAN, and GPIB), two 20-channel DAQM903A Actuator/GP switch modules, and one 20-channel DAQM901A multiplexer module, and a 36-month node-lock BV0006B BenchVue DAQ software with KeysightCare software support subscription. This bundle gives you 10% off the list price.
-
Product
Accessories For DCA Oscilloscopes Family
N1027A
-
N1027A is a collection of accessories for mainframes and modules in the 86100 family of Digital Communication Analyzers (DCAs).
-
Product
Low Side, 200 MHz, 100 PA – 20 MA
CX1103A
-
The CX1103A low side current sensor is a dedicated accessory for the CX3300 series mainframe and features the series widest stand-alone bandwidth up to 200 MHz
-
Product
Mainframe or -E Expansion Chassis - Control up to 16 Modules with up to 8 Relays per Module
LXA/128-MF
-
These Chassis control up to 16 modules with up to 8 relays per module. A large variety of different switch modules are available to build almost any configuration. Modules are available to build matrix or mux configurations or discrete relay modules. Input detection modules, output driver modules and proto board modules allow custom systems for almost any application. LEDs on the front panel show switch and power status. A thumbwheel manual control is optional.
-
Product
Mainframe or -E Expansion Chassis - Preconfigured Single or Two Pole Matrix Systems
LXB/128-MF
-
These Chassis are preconfigured single or two pole matix systems. A single chassis can be a 16x8 matrix, two 16x4 matrices, a single 32x4 or a single 64x2 configuration. Chassis is modular so you may start with a smaller size and increase the configuration as your needs grow.
-
Product
+40dBm Optical Power Head
81628B
-
The 81628B is used with the threaded type adapters. When the adapter is removed, the 8 mm diameter aperture is available for input to open beams or customized fiber holders. The heads are connected to the 816x mainframes using the 81618A single channel or 81619A dual-channel interface module.
-
Product
Multifunction Switch / Measure Unit, Modules
34980A Series
-
The Keysight 34980A multifunction switch / measure mainframe and modules provide functionality that is easy to set up and use. The 34980A helps you lower your cost of test and accelerate your test system integration and development.
-
Product
9025 VXI - 25 Module Solution for VXI
-
The 9025 VXI Receiver is a 25-module solution designed for use with VPC pre-wired interconnect adapters, but can also accommodate a combination of pre-wired interconnect adapters and discrete-wired modules using retainer blocks.1-4 modules attach to an interconnect adapter which in turn is attached to the VXI card. This connector “funnel” forms a complete VXI module, which is easily inserted or removed from the VXI mainframe for maximum flexibility in testing applications. The interconnect adapter also provides room for driver sensors. External cabling to the card is done with a cable clamp or connector located on the top or bottom of the adapter. The positioning of funnels and use of discrete wiring modules can affect the performance of the product. Please contact us for technical assistance.
-
Product
MPOD Micro-1 Crate
-
The Mpod micro-1 crate is the smallest and low cost option for the WIENER multi-channel high and low voltage power supply system. The Mpod micro mainframe can house 1 plug-in low or high voltage modules. The integrated Mpod controller card provides10/100 Ethernet, CAN bus and USB-2 interfaces.
-
Product
Keysight Switch/Attenuator Driver for 34980A
34945A
-
The Keysight 34945A switch/attenuator driver module for the 34980A Multifunction Switch/Measure Unit allows you to control switches and attenuators external to the 34980A Mainframe. This module provides power and control signals for many of the most popular microwave switches and attenuators.
-
Product
Mainframe Chassis
DXM/64x64 and DXM/128x128
-
These Chassis provide a non-blocking, full fan-out matrix in any configuration from 16x16 to 128x128 or larger. Both systems are capable of switching high speed differential CML up to 2.5 Gbps but are most commonly used for ECL, LVDS, LVPECL, Spacewire or RS422.
-
Product
Single Channel, ±40 V, 100 MHz, 40 NA – 1 A
CX1101A
-
The CX1101A single channel current sensor is a dedicated accessory for the CX3300 series mainframe and features wide common mode voltage range. The maximum current can be expanded to 10 A using a CX1206A.
-
Product
Portable Mainframe
Synergy P
-
The Synergy P mainframe supports up to 4 input modules capable of up to 64 channels in a portable, self-contained chassis. Mix and match input modules in any configuration or choose one of the economical bundled configurations.
-
Product
1800 Watt DC Electronic Load Mainframe
N3300A
-
The Keysight N3300A is a full-rack width mainframe with 6-slots that accepts combinations of N330x user-installable load modules (150 W to 600 W) for easy system configuration and future reconfiguration. The N3300A holds up to six N3302A, N3303A, N3304A, N3307A load modules, or three N3305A, N3306A double-wide modules, allowing a total up to 1,800 watts of maximum power.
-
Product
Low-leakage Switch Mainframe
E5250A
-
The Keysight E5250A low-leakage switch mainframe expands a single measurement station, such as the Keysight B1500A, 4155C, or 4156C, to an automated measurement system. Plug-in modules can be configured either as a cross-point matrix for general parametric measurements or as a multiplexer for long-term reliability measurements.
-
Product
Powered VXI Crates
6U VXI-C Size High Power Receiver Crate
-
The WIENER high power C-size VXI receiver mainframe is optimized for test applications with demanding power requirements. Up to 6kW DC power can be provided and distributed to the VXI modules.
-
Product
PXI Infrastructure PXI Mainframe / Components
OTP2 module no.182
-
PXI offers the optimal approach to validation and production testing. You can meet timing, synchronization, and throughput requirements across devices. PXI is a robust PC-based platform for measurement and automation systems, supported by software. PXI combines PCI electrical bus characteristics with CompactPCI's modular Eurocard packaging, and then adds special synchronization buses and important software functions.
-
Product
Modular Power System 6kW Mainframe, 200/208 VAC
MP4301A
-
The MP4300 Series is a family of 1kW Solar Array Simulators (SAS) modular systems in a 2U footprint. The 6kW mainframes can accommodate up to 6 slots of SAS modules achieving excellent power and channel density. Additionally, the SAS series provides a way to simulate solar panels in a spacecraft while offering the highest density, efficient and reliable operation, minimizing rack space to provide the best total cost of ownership.
-
Product
Modular Power
RFP DC Load
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
Product
6U Power Supply Mainframe. Accepts Two Programmable Power Modules
GX7400A
-
The GX7400A is a dual output programmable DC power supply designed for use in 6U PXI systems. The GX7400A occupies three slots and is controlled via the PXI bus. The AC power is provided using a panel-mounted receptacle. The power supplies are fully isolated and can be externally connected in series to provide higher voltage.
-
Product
Modular Power
RFP AC Power
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
