Vector Signal
See Also: Vector Signal Transceivers
-
Product
Large Photo Signal Generator
DDS9m
-
170MHz 4-Channel Signal Generator. The DDS9m generates four independent, phase synchronous sine wave output signals and is programmable in 0.1Hz steps from 0.1Hz to 171MHz. Programming is via an RS232 serial interface. Phase is 14-bit programmable and amplitude is 10-bit programmable. The DDS9m is accurate to 1.5ppm when using the on board TCXO timebase or you can use an external timebase. It requires 3.3 VDC power. SOF8_409 windows software is available as an extra cost accessory.
-
Product
Video Signal Generator
MSPG-6100L
-
MSPG-6100L is basically supporting the Teletext and Closed Caption as multi broadcast for the D-TV9NTSC, PAL), as well as V-Chip (Violence Chip) function to block the violence and sex, etc. bad program to protect a person under age through the regulation grade.
-
Product
FOCL Reference Signal Modem
VCH-607
-
FOCL reference signal modem VCH-607 is designed to receive and transmit electrical signals with a nominal frequency of 100 MHz through a fiber-optic system and generate electrical signals with a nominal frequency of 5 and 10 MHz, coherent with the input signal. Reception and transmission through the FOCL is provided using a pair of modems: one is configured as a Transmitter and is installed at the end of the FOCL where the signal source is located, the second is configured as a Receiver and is installed at the opposite end of the FOCL.
-
-
Product
Signal, Patchcord, ITA, 36", QuadraPaddle, 22 AWG White, Single Ended ( 5 Amps)
7-121922000-036
Signal Patchcord
Signal, Patchcord, ITA, 36", QuadraPaddle, 22 AWG White, Single Ended ( 5 Amps).
-
Product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Male Adapter, .025" Round Post (Adapter Pin)
610138117
Signal Contact (Receiver)
Primary mating contact 610138100. (May mate with other Twin Female contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
Product
Video Signal Generator
MSPG-3233RS
-
Analog was a main item in display device industries at the past time, but from now on, the digital is getting developed with multi-function and large-sized resolution. Preparing for this change, this signal generator is an essential equipment of CRT, LCD, PDP, TV, D-TV display device industries, which was made for generating analog signal, digital signal, and TV signal, D-TV signal, HDCP Code simultaneously and sufficiently examining a large-sized display device.
-
Product
Mixed Signal Test Systems
MTS1000i
-
The MTS-1000i is lowest cost platform available in the MTS series of ATE. It has a reduced platform size compared to the MTS-2010i & MTS-1020i, reduced power supplies, and 4 slots. It is mainly intended for single site testing. Like the other testers in the MTS family it is a highly cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
-
Product
4GHz 2-port Vector Network Analyzer
VNA-0440
-
The VNA-0440 is a full bi-directional 2-port Vector Network Analyzer that is controlled from a PC through a USB connection. It is the cheapest VNA in our VNA-04 series but provides all functionality for antenna development for the low ISM and Wifi bands.
-
Product
Signal Combiner
-
Becker Nachrichtentechnik GmbH
In large scale RF signal distribution systems such as broadcast signal distributions, several signals of radio bands have to be transmitted over longer cable distances. Due to the different frequency ranges, the signals can be transmitted via one common coaxial cable. This saves costs for the coaxial cables and their installation. With help of signal combiners, multiple signal sources can be combined broadband or frequency selective to a sum signal with low loss in level.
-
Product
10 GHz Signal Source
YIG Series
-
The SC5503B and SC5502A are designed to meet demanding low phase noise applications. This is accomplished by employing a multiple phase-locked loop architecture as well as a YIG oscillator as the heart of its synthesizer. Frequency accuracy is provided by an onboard 10 MHz temperature compensated crystal oscillator (TCXO) which can be phase locked to an external reference source if required. These modules can be used as standalone CW signal sources or as LO sources for frequency conversion systems such as the SignalCore IQ modulators and demodulators. They are designed to meet the requirements of many modern applications such as wireless device testing, software-defined radio research, point-to-point radio, multi-channel coherent systems, and other academic and military programs.
-
Product
Analog Signal Conditioning &Isolation Products
DSCIA
-
DSCIA module is a signal channel isolated analog input or output.
-
Product
Digital Signal Processor Card
CHAMP-AV9
-
Curtiss-Wright Defense Solutions
The CHAMP-AV9 combines the floating point performance of the Intel Core i7 processors, with the substantial bandwidth and system-enabling features of the 6U OpenVPX form-factor. Providing a pair of quad-core 4th generation Core-i7 (Haswell) processors, featuring the updated AVX 2.0 instruction units and redesigned on-chip graphics execution units, the CHAMP-AV9 offers a 2-4X performance per size, weight and power improvement over previous DSP modules.
-
Product
Guzik Signal Analyzer
GSA 6000 Series
-
Works with Read-Write Analyzer RWA 4000. Guzik Signal Analyzer (GSA) 6000 series combines high-speed waveform digitizer with built-in digital signal processing hardware and high-speed data transfer link to a computer. The Signal Analyzer comes in a space-saving display-less 2U 19” rack-mounted form factor.
-
-
Product
Mixed Signal Oscilloscope
4 Series MSO
-
With the largest display and highest available channel count in its class, the 4 Series offers unprecedented insight in a bench-friendly package. And its made-for-touch user interface works exactly as you'd expect.
-
Product
Reporting Tool for Dynamic Signal Analyzer
m+p eReporter
-
m+p eReporter is the powerful reporting tool of the m+p Analyzer dynamic signal analyzer. It provides test engineers with comprehensive capabilities for browsing and viewing data, copying & pasting data to ActiveX applications, importing test data from many third-party noise & vibration systems and automating repetitive tasks. This full functionality is available without any measurement hardware connected.
-
Product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
783127-01
Signal Module
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
Product
Signal Injectors
-
Ideal high performance, low noise compliment to your Circuit Sleuth Frequency Response Analyzer. An injection transformer is used to couple an excitation signal from a frequency source into the feedback loop of a control system. This allows loop gain and phase vs. frequency to be measured, with the loop closed, thus characterizing the stability of the system.
-
Product
Signal Conditioners
SC-7400
-
The SC-7400 handles a variety of temperature and process inputs and offers combinations of analog and relay contact outputs. All parameters - such as input and output range, set-points, deadband and burnout - are customer-selectable via software.
-
Product
100MHz Signal Generator
DDS8m
-
The DDS8m generates cosine, sine and ACMOS/TTL outputs simultaneously and is programmable in 1µHz steps from 100Hz to 100MHz. It is also programmable for FSK and CHIRP outputs. The DDS8m is controlled by an RS232 serial interface. Phase can be programmed with 14-bit resolution. The Frequency is accurate to 1ppm when using the on board TCXO timebase or you can use an external timebase. It requires 5 VDC power. SOF8 windows software is available as an extra cost accessory.
-
Product
Traffic Signal Controllers
-
Delve into our ATC Controller Modules to augment functionality and intelligence, ultimately optimizing roadway safety and streamlining traffic operations
-
Product
Arbitrary Signal Generators up to 1GHz
SDG7000A
-
The SDG7000A series are two-channel, multifunctional arbitrary signal generators with a bandwidth of up to 350 MHz, 500 MHz or 1 GHz (upgrades possible). They offer a maximum sample rate of 5 GS/s and 14-bit vertical resolution.
-
Product
Vector Network Analyzer
R42XXE
-
The R42XXE Vector Network Analyzers are designed for measuring of S-parameters, VSWR and impedance of waveguide networks in the full frequency ranges of standard waveguides between 33 and 170 GHz. Frequency accuracy is ±0.2%. The measurement range of reflection factor modulus is from 0 to 1. The measurement range of reflection factor phase is from 0 to ±180° for 0.1< |Гx|<1 with accuracy ±7.5 o in 18-75 GHz frequency range and ±9.6° in 75-170 GHz frequency range. The measurement range of transmission factor phase is from 0 to ±180 o with accuracy ±(5+0.1 |Ax|) o for Ax >-50 dB in frequency range to 75 GHz, for Ax >-30 dB - to 170 GHz. Data can be displayed in the rectangular, Smith or polar diagrams. VNA requires Personal Computer with USB interface.
-
Product
PSD Signal Processing Tool
SEEPOS
-
For most position measurement applications the SiTek SEEPOS system offers a complete and easy-to-use solution. High speed PSD electronics combined with digital signal processing and high speed USB data transfer gives a powerful measurement system. With its large dynamic range it can handle light powers from nW to mW from DC light sources as well as modulated light sources. All parameters, such as PSD bias voltage, amplifier gain, the use of analog and digital filters etc., are easily controlled from the included software and light spot position is continuously displayed both in XY and X-t, Y-t graphs. Optimized plot algorithms ensure that all data is visually seen on the screen even in full speed measurements. Included tools for data analysis and visualization simplify rapid scan through large data sets in order to find specific parts of interest.
-
Product
Clock Signal Generators
-
Optellent offers a range of clock signal generators providing clean reference clock signals up to 32 GHz.
-
Product
Charge Amplifiers & Signal Conditioning
-
The use of charge amplifiers alongside piezoelectric charge output sensors is still widespread in many industries. This is due to the rugged and high temperature capabilities of the sensors. There are many challenges in using these sensors and it needs a good understanding of the technology to get a quality, noise free signal for accurate data.
-
Product
RF Signal Acquisition And Generation Platform
SIGNALlab 250-12
-
The device has full software control over the hardware and additional hardware features compared to other Red Pitaya products. Its larger Xilinx Zynq 7020 FPGA enables greater real-time processing capabilities plus a faster 250Msps sampling rate, and just like other Red Pitaya products it offers the benefits of remote access, with an online app user interface accessible through Ethernet or Wi-Fi.
-
Product
Vector Network Analyzers
P93xxB Streamline Series
-
USB instruments are very common. When shopping for small-form-factor equipment, you may have trouble distinguishing between vendors with similar specifications. The Keysight Streamline Series VNA is based on proven measurement science. It shares a common GUI with high-end instruments — enabling you to implement the Streamline Series into your workflow easily.
-
Product
Precision Signal Chain µModule Solutions
-
Analog Devices’ precision signal chain μModule® solutions utilize heterogeneous integration to provide a complete solution to precision data conversion. These solutions reduce design iterations by transferring the component selection, optimization, and layout from the designer to the device. They also significantly reduce the footprint, total cost of ownership, and time to market for system-level designers.
