Vector Signal
See Also: Vector Signal Transceivers
-
Product
16-Channel Analog Multiplexer & Signal Conditioning Card
AIM-16
-
Model AIM-16 accepts, pre-amplifies, and multiplexes analog signals for application to an analog-to-digital converter installed in a host computer. Each AIM-16 concentrates 16 differential analog input channels into one single-ended analog output channel. Up to eight AIM-16s can be cascaded providing total capacity for 128 inputs to an "8-input A/D Converter."
-
Product
304/1 Vector Network Analyzer Rack Mount Kit
-
This rack mount kit is for the Planar 304/1. It includes track slides and handles for the full size USB VNA.
-
Product
REMOTE-CONTROLLED SIGNAL GENERATOR
ASX-16C/D
-
Matrix Test Equipment Incorporated
The Model ASX-16C/D is a newer design version of the standard Model ASX-16C. The use of enhanced technology allows greater frequency trim (+/- 25 KHz) while maintaining the excellent noise and distortion performance of the ASX-16C. The Model ASX-16C/D also provides linear monotonic carrier level control over a 15 dB range in 0.025 dB steps
-
Product
170-Pin Signal Block
-
Adapter Pylonlock 170-pin signal block: small inner cone (IK06) standard - and high gold-plated / large inner cone (IK10) / plan (P).
-
Product
Digital Signal Processor Card
CHAMP-AV9
-
Curtiss-Wright Defense Solutions
The CHAMP-AV9 combines the floating point performance of the Intel Core i7 processors, with the substantial bandwidth and system-enabling features of the 6U OpenVPX form-factor. Providing a pair of quad-core 4th generation Core-i7 (Haswell) processors, featuring the updated AVX 2.0 instruction units and redesigned on-chip graphics execution units, the CHAMP-AV9 offers a 2-4X performance per size, weight and power improvement over previous DSP modules.
-
Product
GPIB Controlled Signal Routing Box
3000GPIB
-
Test Electronics will customize the TE3000 GPIB signal routing box for your test application. Then, you simply rack and stack all the equipment, cable all the switched signals to the back of this GPIB box, add a rack mount computer, plug in the National Instruments GPIB board and software. Then run your customized GPIB based test system.
-
Product
Mixed Signal Oscilloscopes
-
Fully configured USB 2.0 oscilloscope - 14 bit 100 MSa/s, 2 analog channels, 8 digital inputs, External Trigger, 8M samples storage for each of the 2 analog and 8 digital channels, CS700 Signal Generator (0-10MHz, Sine, Square, Triangle). Complete with the CS300 application software, 2 x CS1001 and CS1004/5 probe sets. The front panel ground is continuous via the USB ground to the PC.
-
Product
PXI 34x4 Signal Insertion and Monitor Matrix
40-525A-001
Matrix Switch Module
This is a PXI signal insertion and monitor matrix with switched pass thru connections on both X and Y axis. It is also availablein a 16x4 format and can be used for signal insertion and monitoring purposes on connections between the UUT and test system. Each pass thru connection from LX to X can be open or closed to allow the programmatic disconnection of the signal to check the response of the UUT. The matrix can be used to connect test equipment, such as a DMM or scope, to monitor the pass thru signals via Y connections while the LY connections can be used to insert a fault condition or insert external signals. When external signals are injected the LX connections can be opened and the LY connections closed.
-
Product
Mixed Signal Test Systems
MTS2010i
-
The MTS-2010i are a cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process.
-
Product
Small Signal RF/Microwave Power Amplifier
-
R&K’s small signal amplifier series are to amplify various high frequency signals such as CW/Pulsed/AM/FM/N-DCMA/W-CDMA/OFDM , etc.
-
Product
64 Channel Dual IF Signal Processor
DP-VME-5247
-
DP-VME-5247 is a VME64x Dual IF Signal Processor . This dual channel up converter and down converter on-board real time data processing and analog output. This board is particularly suited for radar systems where the signals must be sampled at high rates and very high purity programmable signal generation. Application range encompasses IF signal processing, radar systems, communication systems, and IF data logging systems.
-
Product
VHF/UHF Handheld Signal Location Antennas
Type NVF-2
-
The Type NVF-2 series of handheld directional antennas are used to locate interfering signals or noise in either the 420 – 470 MHz (Type NVF-2A) or the 900 MHz ISM band or cellular telephone bands (Type NVF-2B). Both models incorporate a solid reflector positioned behind a resonated half wave driven element, both elements being mounted on a fiberglass rod with an integral pistol grip. The configuration of the reflector and driven element are such that a deep null in the signal being received will occur when the antenna is pointed in the direction of the signal being radiated. A T-pad resistive attenuator is also incorporated in the antenna mounting enclosure to aid in the direction finding process on very strong signals or when excessive reflections present multiple returns.
-
Product
Signal Generators
-
Precision Test Systems manufacturers various signal generators. We can also supply other manufacturers or used signal generators. Our main signal generators are listed below.
-
Product
Head Mount Signal Conditioners
-
Head mount signal conditioners are designed to mount in industrial protection heads for use with thermowells. The sensors are small sized and offered in a variety of input and transmission options.
-
Product
Output Signal Cable
CoXX-G
-
The Output Signal Cable CoXX-G is designed for optimal compatibility with SENIS analog magnetic transducers, including models F3A, F1A, and I1A. Available in multiple lengths – specifically 2m (CO20-G), 5m (CO50-G), and 10m (CO100-G) – this cable is equipped to deliver precise temperature-proportional output voltage. Its robust construction includes a metal case connector that is securely connected to the cable shield, ensuring durability and reliability in various applications.In addition to its length specifications, the CoXX-G series features unterminated wires at the cable end, enhancing versatility for users needing to tailor connections for specific setups. The cable is structured with a 7-pin connector layout, detailed with specific wire color coding for each output signal: X+ (brown), Vtemp (red), Z+ (grey), Y- (green), Y+ (yellow), X- (white), Z- (rose), and GND (blue). With these features, the Output Signal Cable CoXX-G is an excellent choice for professionals requiring high-quality signal transmission and flexibility in their setup.
-
Product
Mixed Signal Oscilloscopes
-
The design, validation, and manufacturing of modern electronics necessitate the measurement of both analog and digital signals. Mixed signal oscilloscopes enable the simultaneous, time correlated observations and analysis of analog with digital (logic) signals, to establish causal relationships between the various areas of a device's electronics. They are purpose built tools for troubleshooting electrical anomalies, measuring parametric values, and monitoring cause and effect relationships between signals.
-
Product
Rapid Measurement of Digital TV Signals
TM982
-
TM982 Rapid measurement of digital TV signals
-
Product
Digital Combo Set for Measuring Low-Frequency Signals
SVG-5
-
- Measurement of root-mean-square AC voltage and frequency of single-ended or differential signals- Measurement of AC voltage frequency of single-ended or differential signals- Generation of sine waves- Visual examination of freeform signals- Signal spectrum analysis
-
Product
SAT/CATV/TV Signal Analyzer
DSA 1491
-
9” full-color, high-resolution touch screen user interface simplifies complex measurement tasksRF inputs including satellite, cable and terrestrial along with ASI and IP inputsDigital RF measurements including average power/level, pre/post BER, MER, noise margin, spectral analysis and constellation
-
Product
Signal Calibrators
-
Nagman Instruments & Electronics Pvt. Ltd
If you are looking for Signal calibrators that are best in industry, head over to Nagman website immediately. We have a range of signal calibrators, loop calibrators, milliamp calibrators, process meter and more. Depending on the requirement at hand, you can find a signal calibrator that is best suited for your industry. Signal calibrators can be used for calibrating thermocouples, RTD, transmitters, etc. while loop calibrators are used for calibrating controllers, indicators, etc. Nagman’s range of signal calibrators are handy, light weight, portable and durable.
-
Product
Signal Sources
-
Frequency multipliers, oscillators, beacon transmitters or microwave TV-transmitters: The signal sources of Kuhne electronic meet the highest quality standards and are remarkable for high spurious and harmonic rejection, low phase noise and very good frequency stability. Benefit from our experience in satellite technology and the commercial sector!
-
Product
Vector Network Analyzer Automation
-
CMT’s vector network analyzer software supports multiple automation languages, including C++, Python, MATLAB*, Visual Basic (Excel)*, and LabVIEW*. Our command set is modeled after industry-standard legacy equipment; porting code is straightforward, and we can help.
-
Product
Signal Processor Board
MS 1532
-
- Frequency coverage from 5 kHz to 30 MHz in 1-Hz steps- High dynamic range: +30 dBm 3rd-order intercept typical- Digital filtering provides 58 IFBWs from 56 Hz to 8.0 kHz with exceptional shape factors- AM, Synchronous AM, FM, CW, USB, LSB & ISB detection modes standard- Tunable notch filter- Fast, flexible scanning with 100 memory channels- Large readable LED displays & user-friendly controls- Noise blanking & pass band tuning- Internal switchable preamplifier & attenuator- Operator-selectable RS-232, RS-485, or- RS-422 remote control- Viretx 5 FPGA based design (Two virtex for image processing)- LPC2468 ARM 7 Processor based design- MIL1553B and RS485 Interface- Two High speed 14 bit ADC (125MSPS) for I & Q Sampling- Direct sampling 2-30MHz- Audio CODEC- Conduction Cooled Board
-
Product
Digital Signal Processor Card
CHAMP-FX2
-
Curtiss-Wright Defense Solutions
Utilizing a 6U VPX-REDI form factor, the CHAMP-FX2 FPGA-based computing platform harnesses the tremendous computing power of two Xilinx Virtex-5 FPGAs, combined with the high-performance floating-point capabilities of the NXP (formerly Freescale) MPC8641D dual-core Power Architecture processor and the performance and flexibility of a Serial RapidIO switching fabric to flexible computational performance.
-
Product
Signal Path Analyzers
HL2200 Series
-
HYPERLABS HL2200 Series Signal Path Analyzers™ provide high-performance test and measurement capabilities for a fraction of the cost of traditional benchtop systems. These differential, multi-channel instruments are ideal for interconnect characterization, debugging cable assemblies, coupon testing, controlled impedance analysis, and other applications requiring a fast rise time.
-
Product
Signal Conditioning
-
Sensors that are used to collect the data from the environment often don’t produce signal of characteristics optimal for an analog to digital converter (ADC) to translate to digital data. Additionally, these signals can be subject to electromagnetic interference (EMI) that introduces noise, having a negative impact on the reliability of the data. To make this analog input readable for the processing unit and dependable enough to give the desired quality of data the signal has to undergo a process of signal conditioning.
-
Product
9kHz to 20/40GHz Signal Generator
CSG Series
-
Corech Microwave’s CSG series of Compact Microwave Signal Generators（Signal Source）operate from 9kHz to 20GHz / 40GHz. It offers high dynamic output power -120 to +17dBm, ultra low phase noise: -105dBc/Hz@10KHz, low harmonics and spurious. These exceptional performances make CSG9K20GA / CSG9K40GA an ideal choice for many test and measurement applications, including Semiconductor, Quantum Technology, Radar and Communication etc.
-
Product
Power and Signal Twist Capsules
-
Power and Signal Twist Capsules are used when only limited rotating is required and/or sliding contacts cannot be tolerated.
-
Product
Signal Converters
-
ams signal converters contain four or eight signal channels, and can be dynamically programmed in-process by means of multiple amplification levels. This makes them very well suited for multi-channel sensor systems in applications with dynamic amplification and a high sensor bandwidth. All the converters small: they are available in space-saving (Q)SOP packages or as Chip-on-Board(COB) packages.
-
Product
Signal Amplifier
A10150
Amplifier
Model A10150 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, low distortion, signal amplification. With a high bandwidth of 150MHz, 20Vp-p into 50 ohms and a fast transition time of less than 1.8ns, the A10150 is the ideal complimentary amplifier to any high speed signal source that needs a supporting power boost for demanding applications.
