Vector Signal
See Also: Vector Signal Transceivers
-
Product
Vector Network Analyzer Automation Suite
ZNrun
-
For a facility manager the yardstick for optimization could be maximizing the daily production yield, while for a test-engineer it might mean being able to easily define a test setup and have it loaded on each device in the factory in seconds. A tester might be interested in seeing only the result of the measurements, after having started it by scanning a barcode, while quality managers might find it convenient to be able to download real-time yield statistics on their way to the factory. The R&S®ZNrun software suite was designed with optimization in mind and acknowledges these re-quirements by offering each party the possibility to expedite their workflows as much as possible.
-
Product
Signal Conditioners & Interface
-
Modbus RTU Remote Connectivity and Control. Minimize Long Cable Runs with Modbus Network. Pulse to Frequency Conversion. Shaft Speed Pulse to DeviceNet. Shaft Speed Pulse to 4-20 mA Conversion.Sensor Compatibility
-
Product
FOCL Reference Signal Modem
VCH-607
-
FOCL reference signal modem VCH-607 is designed to receive and transmit electrical signals with a nominal frequency of 100 MHz through a fiber-optic system and generate electrical signals with a nominal frequency of 5 and 10 MHz, coherent with the input signal. Reception and transmission through the FOCL is provided using a pair of modems: one is configured as a Transmitter and is installed at the end of the FOCL where the signal source is located, the second is configured as a Receiver and is installed at the opposite end of the FOCL.
-
Product
Video Signal Distributor
MSHD-02
-
MSHD-02 distribute inputted component signal to the two (2) output channels via RCA connectors without diminuation & distortion. It takes High Bandwidth Video Distributor IC which is support the highest component resolution up to 1920X1080P & Dot Clock 148.5MHz.
-
Product
Signal Contacts
-
VPC’s signal contacts are high reliability, modular connectors used to route low voltage, low current signals within VPC’s mass interconnect test systems. They provide durable, high cycle electrical connections—via families such as TriPaddle and QuadraPaddle—supporting dense, configurable interfaces
-
Product
Signal And Spectrum Analyzer
FSVA3000
Spectrum Analyzer
An analysis bandwidth of 400 MHz, an outstanding phase noise of –120 dBc/Hz and a high dynamic range – the R&S®FSVA3000 signal and spectrum analyzer has everything needed to keep up with demanding measurement applications such as 5G NR. With its high measurement speed and easy usability, it is the right instrument for demanding signal analysis tasks both in the lab and on a production line.
-
Product
Signal Generator
-
This signal generator is a powerful tool in audio equipment analysis. Together with the analyzer "WinaudioMLS" a rich set of measurements can be performed. This generator is available in a freeware version and a PRO version.
-
Product
Mixed Signal Test Systems
MTS1010i
-
The MTS-1010i is a more economical version of the MTS-2010i & MTS-1020i testers. It has a reduced platform size and reduced power supplies. Like the other testers in the MTS family it is a highly cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process.
-
Product
Multi-purpose Signal Conditioners
-
The 482C series comprises 4-channel benchtop signal conditioners, while the 483C series offers 8-channel rack-mounted units. Utilizing identical signal conditioning electronics across equivalent 4 and 8-channel models ensures consistent performance. Both signal conditioner series offer standalone units with essential functionalities, as well as units equipped with advanced features like a front panel keypad and display or an Ethernet port for computer control. Additional features encompass gain adjustment, filtering options, LED fault indicators, and TEDS capability.
-
Product
Cab Signal Master
-
Cab Signal Master is a microprocessor based system specially developed to test all cab signal equipment in railroad locomotives and transit cars. Programmable default setting and straight forward operations allow simple "plug it in, turn it on" operation with very little instruction.
-
Product
Signal Transformers
-
Signal transformers are used as a step-up / step-down, isolating, or impedance matching component in electronic devices.
-
Product
CATV & RF Signal Products
-
Wuhan Sunma Technology Co., Ltd.
SunmaFiber is a worldwide leading provider for fiber optic equipment, fiber optic test instruments and other data network & telecom products of communications, commercial, and consumer markets. The Company offers test and measurement systems and services to telecommunications service providers, cable operators, and network equipment manufacturers. In addition, the Company offers components, modules, and subsystems for Wireless, Telecommunication, Datacom, Power, Cable TV measurement instruments and utilities applications.
-
Product
FieldFox Handheld Microwave Signal Analyzer, 54 GHz
N9963B
Signal Analyzer
A lightweight, durable, software-enabled, microwave signal analyzer, interference analyzer, distance-tracking generator, preamplifier, power meter, and more.
-
-
Product
Signal Integrity Test Products
S1
-
*Fixtureless Test Solution*Automated Optical Inspection*DC Electrical test*Tests any backplane – Small, large, simple, complex*Now available with 4 heads
-
Product
HD Pattern Signal Generator
-
Evaluate, Calibrate, and Test Digital Video Equipment. Advanced testing device for your audio and video equipment.
-
Product
Signal Routing Software
Switch Path Manager
-
Our signal routing software, Switch Path Manager, simplifies signal routing through switching systems and speeds up the development of switching system software. Switch Path Manager supports Pickering''s switching modules and the interconnection between these products. Third-party products can be supported upon request. Once a switching system model has been created, simply defining the endpoints that are required to be connected together can perform signal routing. The ability to automate signal routing results in effective and easy switching system managementsafely and quickly.
-
Product
PXIe-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
780587-12
Signal Module
PXIe, 7-Channel, 10 A PXI Signal Insertion Switch Module—The PXIe‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
Product
Standard Signal Isolating Amplifier
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Isolation and conversion of standard signals. Calibrated switchable inputs and outputs 0/4 ... 20 mA and 0 ... 10 V signal duplicator with two electrically isolated outputs.
-
Product
Signal Generators
-
One of a class of electronic devices that generates electrical signals with set properties of amplitude, frequency, and wave shape.
-
Product
Mixed Signal Test Systems
MTS1000i
-
The MTS-1000i is lowest cost platform available in the MTS series of ATE. It has a reduced platform size compared to the MTS-2010i & MTS-1020i, reduced power supplies, and 4 slots. It is mainly intended for single site testing. Like the other testers in the MTS family it is a highly cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
-
Product
Signal Splitters
-
The DAT4530 can convert any process signal (Thermocouples, RTD, mV, Voltage, mA Resistance and Potentiometer) to a voltage or current output (4-20mA, 0-20mA or 0-10V). Each output can be different and it also has a built in limit alarm which is an SPST relay. The DAT4530 is PC programmable with the aid of the Prodat programmer and the Datasoft software which is available from the Datexel down load page. The DAT4530 is also programmable with the aid of 3 DIP switches which can be found on the side of the DAT4530. There is full isolation between the input, power supply, limit alarm output and two outputs.
-
Product
Signal Conditioners
SC-1300
-
The SC-1300 family of signal conditioners can convert the most commonly used process signals into conditioned current and voltage outputs, needed for control systems and monitoring devices. Dedicated functionality and isolation from control systems improves reliability.
-
Product
Signal Amplifier
9100
Amplifier
Model 9100 is a Single/Dual Channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9100 amplifies signals from DC to over 500kHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.
-
Product
Signal, Spectrum, & Modulation Analyzers
-
A tool used to analyze data. For example, a gas analyzer[1] tool is used to analyze gases. It examines the given data and tries to find patterns and relationships. An analyser can be a piece of hardware or software.
-
Product
TAP Signal Isolation Module
JT 2139
-
The JT 2139 is a TAP signal isolation module designed for use in combinational test systems that utilise multiple instrument interfaces. To avoid parasitic capacitance effects and/or unwanted ground loops the JT 2139 can be used to completely galvanically isolate any JTAG Technologies boundary-scan controller from the remainder of the instrumentation system. JT 2139 isolators are a standard component of the JTAG Technologies ‘Symphony’ systems that integrate boundary-scan with In-Circuits Testers etc..
-
Product
Electronics For Signal Processing
-
PCB Piezotronics manufactures a wide variety of electronics to power ICP®, PE (Charge Mode), MEMS, strain gage and other types of sensors. All of these products provide conditioning of sensor signals for transmission to data acquisition systems.
-
Product
Signal Board
iDSC 1816
-
The iDSC 1816 board from Microstar Laboratories combines 16-bit resolution on eight simultaneous channels of data acquisition with brick-wall anti-alias filters on each channel. The iDSC 1816 samples analog inputs at a throughput of 1.2M samples per second, with the sampling rate on each channel ranging from 8 samples per second to 153.6k samples per second.
-
Product
Signal, Patchcord, ITA, 36", QuadraPaddle, 5 Amp, 22 AWG White Twisted Pair, Single Ended
7-121422000-036
Signal Patchcord
Signal, Patchcord, ITA, 36", QuadraPaddle, 5 Amp, 22 AWG White Twisted Pair, Single Ended.
-
Product
PSD Signal Processing Tool
SEEPOS
-
For most position measurement applications the SiTek SEEPOS system offers a complete and easy-to-use solution. High speed PSD electronics combined with digital signal processing and high speed USB data transfer gives a powerful measurement system. With its large dynamic range it can handle light powers from nW to mW from DC light sources as well as modulated light sources. All parameters, such as PSD bias voltage, amplifier gain, the use of analog and digital filters etc., are easily controlled from the included software and light spot position is continuously displayed both in XY and X-t, Y-t graphs. Optimized plot algorithms ensure that all data is visually seen on the screen even in full speed measurements. Included tools for data analysis and visualization simplify rapid scan through large data sets in order to find specific parts of interest.
