Impedance
-
product
NF-SM 50 N-Female to SMA-Male Adapter
NF-SM 50 Adapter, N-Female to SMA-Male, Frequency Range: DC to 18 GHz, Impedance: 50 Ohm
-
product
Bench Type LCR Meter
LCR-900
*Dual LCD Display. *Capacitance, Resistance, Impedance, Inductance, Quality Factor, *Dissipation Factor Phase Angle. *Auto Detect Function. *Open Circuit/Short Circuit Compassion. *Operation Frequency 100Hz to 100KHz. *Basic Accuracy: 0.3% *Measurement Voltage Fixed at 0.6Vrms.
-
product
Impedance Standards and Calibrators
Impedance Calibrator is to replace countless single value RCL standards with one calibrator that can switch between the standards like a CD changer in your car. The calibrator contains stable and temperature independent resistance standards, partial capacitance standards and partial inductance standards, simulated by RC T-type passive network. Calibration values of both complex parameters of partial standards are displayed on large LCD screen in preselected pairs of parameters as well as voltage, current and frequency readouts from built-in test signal meter. OPEN and SHORT reference positions are available as well.
-
product
Cable Fault Locator
TX2003
6 km (19,000ft) 0.5mtr dead Zone Selectable Cable Impedance Warble Tone Generator Rapid Fault Location Large 128x64 LCD with Backlight Scratch Resistant Display Environmental Protection IP54 CE Approved 3yrs Manufacturers Warranty 60 Hours Battery Life
-
product
Precision Impedance Analyzer
TH2851-080
Changzhou Tonghui Electronic Co., Ltd.
■ Test frequency: 10Hz-80MHz ■ High precision: using automatic balance bridge technology, four-terminal pair test configuration
-
product
Standard 1.59 (40.40) - 7.00 (198.50) High Frequency Probe
CSP-30TS-011
Nominal Impedance (Ohms): 50Current Capacity (Amps) @ 20° C: 1.00Bandwidth @ -1dB (GHz): 35.00Recommended Travel (mil): 67Recommended Travel (mm): 1.70Full Travel (mil): 100Full Travel (mm): 2.54Overall Length (mil): 1,003Overall Length (mm): 25.48Rec. Mounting Hole Size (mil): 213Rec. Mounting Hole Size (mm): 5.40Test Center (mil): 375Test Center (mm): 9.53
-
product
CellTest Multichannel Potentiostat
Simultaneous Electrochemical Impedance Spectroscopy (EIS) tests can be run on multiple cells by connecting Solartron 1455A/1451A series frequency response analyzer (FRA) modules to the 1470E. These FRAs can operate in single sine correlation or multi-sine / Fast Fourier Transform (FFT) analysis mode, providing the ultimate in speed, precision and accuracy. The 1455A FRA provides high performance impedance measurements over the frequency range 10 μHz to 1 MHz, while the 1451A FRA operates from 10 μHz to 100 kHz.
-
product
Micro Coax, Contact, ITA, 50 GHz
610141108
Primary mating contact 610140108. (May mate with other Receiver contacts, as well.) *This contact sold as a patchcord only.Mechanical SpecificationsDurability 10,000 cyclesContact Material Center Conductor – BeCuShield – BrassContact Plating 30µ" Au over 100µ" NiContact Termination Solder Nut ClampInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC-50GHzVSWR 1.06+0.004 f(GHz)Insertion Loss - .095 x √f(GHz) dBDWV 700 V RMSContact Resistance 6 mOhms center/4 mOhms outer Cable Specifications Flex 405Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
product
Adapter
P350NM75NF
P350NM75NF Adapter, Frequency Range: Up to 12 GHz, Impedance: 50 Ohm to 75 Ohm
-
product
Digital Electrical Network Analyzer
1826 NA
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Measures Earth Resistance without the need for poles in the ground or external measuring wires.● Earth measurement uses the real earth current path and the current generated by the electric network, without the need for any disconnection.● The Earth Resistance displayed is exactly the earth resistance that the earth current will need to go through if an earth fault occurs. No need to add all the bonding points and connection paths resistances.● Displays voltage supply at the transformer (Line to Neutral), without loading the transformer. Displays voltage between Line (Phase) and Earth (Ground), without drawing any current.● Measures the impedance of the line itself so you can analyze and differentiate between the multiples paths of the wiring.● Measures the Neutral Impedance. Single one smart push button operation; ON, Test, Scroll trough results and menus.● Checks wiring integrity (LEDs).● Auto off/auto ranging (software ranging). ● Combined prospective short circuit current, loop, individual wire and Earth Tester.● Voltage test L-N and L-E.● Loop test for L-E and L-N and PSC.● Enables analysis of constituent components in L-E and L-N loops giving resistance of earth, neutral wire, live wire and transformer winding.● Display can be customized for large orders.
-
product
Automatic Tuners10MHz – 140GHz
Load Pull
An impedance tuner is an apparatus, which generates controllable reflection factor (Impedance) over a certain frequency range.
-
product
Electrical Impedance Tomography
Electrical Impedance Tomography (EIT) is an imaging technique that visualizes conductivity or impedance distributions both in 2D and in 3D. Sciospec is partnering with world leading scientists in the field to deliver solutions that enable using EIT both in research and in practical applications.
-
product
Radio Vector Tester
Wuhan Sunma Technology Co., Ltd.
Radio & Vector Network Analyzer adopts the advanced digital and RF combination design technology, fundamental wave frequency mixing technology, digital IF processing technology, intelligent power management technology, etc. It comes with features of high precision, small size, light weight, battery power, can measure SWR, Return Loss, Cable Loss, Impedance, DTF, etc, is used to the field test of cable, feeder, and the reflection parameters test of RF components in science and teaching. SunmaFiber provide all kinds of CATV meters, such as Signal Level Meter, QAM Analyzer, Spectrum Analyzer, DVB/DVC/DVT Analyzer and other TV testers.
-
product
Transducer Simulator
Model 7V
Impedance: 350 ohms nominal. Output Ranges:Fixed rotary switch: 0 to 3 mv/v in 6 steps of .5 mv/v .
-
product
Differential Probe
DP-08VF
*MAX. Input Voltage: ±400V DC or 800V p-p or AC 280V rms*Bandwidth: DC-150MHz*Input Impedance 20MΩ // 5PF*X20, X200 Attenuator*To Ground MAX. Voltage: 400V*Output Impedance 50Ω
-
product
Electrical Tester For Voltage
PDT35
Automatically Selects VAC, VDC, or Continuity TestComplies with EN 61010-1 For Use in CATIII 600 V Environments1999 Count LCD DisplayAuto Power On/OffHigh Input Impedance -- 400 kVoltage AC: Max Range 600 V, Accuracy +/- 1.5%Voltage DC: Max Range 600 V, Accuracy +/- 3.0%Continuity TestAccessories Included: Test Leads, 2 'AA' BatteriesDimensions: 8.46' H x 2.83' W x 1.44' DWeight: 8.29 oz.Sold as : Unit
-
-
product
Time Domain Reflectometer
STEP TDRS
Cable Measurements: Distance, Fault Types, Distance to Faults, Impedance Readings, and Loop Resistance.
-
product
Calibration Kit
N1801
*, *N1801 Calibration Kit, *Frequency Range: up to 18 GHz, * Impedance: 50 Ohm, * Connector Type: N-type.
-
product
Cable Fault Locator
TX4000
Auto Fault Location Rugged Palm-Top design Weighs less than 350g (12oz) 11 Measurement Ranges up to 4000m 25, 50, 75 & 100ohm Selectable Cable Impedance User Variable Gain Control Built in Tone Generator for Pair Tracing and Identification Suitable for testing all Communication and Power Cables Environmental Protection IP54 CE Approved Soft bag & Test Leads
-
product
Differential Probe
DP-16V
*MAX. Input Voltage: ±8KV DC or 16KV p-p or AC 5.6KV rms*Bandwidth: DC-50MHz*Input Impedance 30MΩ// 1.5PF*x20, x200, x2000 Attenuator*To Ground MAX. Voltage: 8KV CAT III*Output Impedance 50Ω
-
product
Performance Board For LSI Tester
Place inner layer GND plane all over. Impedance control of signal line and crosstalk prevention, etc. contribute to improvement of characteristics in various ways.
-
product
Audio Impedance Testers
1106 IM
Standard Electric Works Co., Ltd
Large LCD : 68 × 34mm (2.677" × 1.338"). True measurement of speaker systems actural impedance at 1kHz. Three test ranges allow testing of home theater and commercial sound systems. Measures transformer impedances. Battery operation. Low battery indication. Data hold function. 0Ω adjustment.
-
product
NM-SM 50 N-Male to SMA-Male Adapter
NM-SM 50 Adapter, N-Male to SMA-Male, Frequency Range: DC to 18 GHz, Impedance: 50 Ohm
-
product
Impedance Analyser Frequency Response Analyser
C60
The C60 investigates the opaque world of analog networks. The unit operates in two test modes. It can measure the frequency response of a two port system producing a gain/loss and phase graph. It can also measure the reactive response of a two terminal network producing an impedance/admittance and phase graph. Electronic, electrical, electro-acoustic and other networks can be tested with sine wave excitation and the results displayed on a PC.
-
product
Mini Coax, Contact, ITA, one .025"
610103150
Mini Coax, Contact, ITA, one .025" Round Post/ one .02" Square Post/ .075" Spacing.Specifications Characteristic Impedance 50 OhmsFrequency Range DC to 1 GHzInsertion Loss 1.2 dB @ 1 Ghz1.02 dB @ 500 MhzVSWR ≤ 1.06 @ 1 GhzOperating Voltage & Current 0.5 Amps Max. ContinuousMating Force 1.5 lbs Max [0.68Kg]Dielectric Withstanding Voltage (DWV) 1500 VDC Min.Insulation Resistance 1000 MOhms Min.Contact Body Shield – BrassCenter Conductor – BeCuContact Plating Shield – 50µ" Au over 100µ" NiCenter conductor – 60µ" Au over 100µ" NiCycle Life 20,000 Cycles
