-
Product
HL Deadweight Tester
-
AMETEK Sensors, Test & Calibration
The HydraLite Tester is a primary standard available as a dead weight tester or a gauge. Both feature a re-entrant type measuring piston and cylinder assembly. This design reduces the rate of fluid leakage and increases float time, helping to maintain accuracy as test pressures increase.
-
Product
Tire Pressure Gauge
-
ZhangZhou Weihua Electronic co.,ltd
Is a pressure gauge used to measure the pressure of tires on a vehicle. Since tires are rated for specific loads at certain pressure, it is important to keep the pressure of the tire at the optimal amount.
-
Product
Torque Measurement Trainer Module
-
Unitech Scales And Measurements Pvt. Ltd
Torque Measurement Trainer comprises of strain gauge based reaction type torque transducer, fulcrum arm of 1 M length with L angle to mount the sensor, Pan & weights with digital torque indicator to read the torque in Kg-m.
-
Product
Asphalt Layer Thickness Measurement Devices
-
ElektroPhysik Dr. Steingroever GmbH & Co. KG
Non-destructive road layer thickness measuring gauge to measure bituminous road layers or other electrically insulating road layers.
-
Product
IEC60529 Jet Nozzle IPX5/6
CX-IPX5
-
Shenzhen Chuangxin Instruments Co., Ltd.
Test Set consists of a jet handle that is equipped with a pressure gauge and an easy-to-adjust flow valve.The interchangeable nozzles assemble easily to the jet handle. The nozzles are made from stainless steel.
-
Product
Pfund Thickness Gauge
3233
-
Available in aluminium or stainless steel this instrument consists of two concentric cylinders, one sliding inside the other. A spherical glass lens, which has engraved measurements, is fitted to the end of the central cylinder and when pressed into the wet film, leaves a circular trace.The diameter of the mark on the lens is measured and, using the supplied conversion table, the thickness of the coating can be easily assessed.Ideal for measuring the thickness of wet translucent products such as varnishes, oils etc.Measurement range of 2.25 - 360μm (0.09 - 14.17mils)
-
Product
PXI Strain Gauge Simulator Module 4-Channel, 3k
40-265-104
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 3kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
Automatic Pull-Off Adhesion Gauge
510
-
Automatic hydraulic pump ensures smooth and continuous pressure application for consistent, repeatable adhesion strength resultsFully adjustable pull rates 0.1-1.4MPa/s (14.5-203psi) to meet National and International StandardsCan be used with 10,14.2, 20 and 50mm diameter dolliesUser definable limits with unique pressure hold and release functionUser definable measurement range with an accuracy of ±1% of full scale:10mm dolly: 100MPa (14400psi14.2mm dolly: 50MPa (7200psi)20mm dolly: 25 MPa (3600psi)50mm dolly: 4MPa (580psi)Dust and water resistant rugged design to IP64Interchangeable units: MPa, psi, Nmm2 and NA range of standard and thin substrate actuator skirts (compatible with Elcometer 506) available for adhesive strength testing on thick, thin, flat or convex substratesStore up to 60,000 readings with individual pull graphs in up to 2,500 alpha numerical batches, complete with attribute failure informationUSB and Bluetooth® data output - compatible with ElcoMaster® App for iPhone, iPod, iPad and Android mobile devices
-
Product
Lamp gauge
E27
-
Shenzhen Chuangxin Instruments Co., Ltd.
To check the maximum dimensions of the screw thread and dimension T1 minimum of caps on finished lamps shown on sheet 7004-2.
-
Product
Ultrasonic Thickness Gauge
TI-45 Series
-
You can instantly measure the thickness of a material simply by positioning a probe. This innovative gauge is widely used and is capable of measuring a variety of materials including iron, stainless steel, glass and ceramics.
-
Product
COMPRESSION, VACUUM AND FUEL PUMP TESTER COMBO SET
MCVK
-
*Tests compression on all domestic and import cars and trucks with gasoline engines*Compression tester kit includes: 2-1/2" gauge with dual inch/metric readings: 0-300 psi and 0 to 21 kg/cm2, 14mm/18mm solid short adapter, 14mm/18mm long flexible adapter and 14mm long reach adapter*Checks vacuum and fuel pump pressure and locates air leaks in fuel lines, vacuum operated chokes and emission control systems on all domestic and import cars and trucks with gasoline engines
-
Product
Strain Gauge Weighing
-
In the demanding environment of the metals processing industry getting the right balance between accuracy, speed and reliability in your sensing systems can mean a great deal. ABB offers a wide range of dedicated products for weighing applications for crane, scrap, blast furnace and continuous casting.
-
Product
Fume Hood Controller
FHC50-01
-
Fume hoods are a primary source of protection in laboratories. Face velocity measurements are often used to gauge the performance of a fume hood’s ability to contain and exhaust harmful vapors. By measuring and controlling face velocity, TSI FHC50 Fume Hood Controllers provide a higher level of fume hood safety and energy efficiency.
-
Product
Isolated Strain Gauge Input Module
ADAM-3016
Strain/Bridge Input Module
1000 VDC 3-way optical isolationSwitch configurable mV or V input of full bridgeSwitch configurable voltage and current outputs
-
Product
Axial Extensometer
Model 3542
-
Jinan Testing Equipment IE Corporation
These extensometers are designed for testing a wide range of materials, including metals, plastics, composites and ceramics. All will work in both tension and compression. The dual flexure design makes them very rugged and insensitive to vibrations, which permits higher frequency operation.They come standard with Epsilon’s quick attach kit, making it possible to mount the extensometer on the test specimen quickly and easily with one hand. The quick attach kit can be removed, allowing mounting of the extensometer with springs or rubber bands.The Model 3542 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.For gauge lengths 100 mm (4 inches) or greater see Model 3542L.
-
Product
Mechanical Coating Thickness Gauge
211
-
This is one of the most popular mechanical coating thickness gauges in the world.Factory calibrated - with user calibration adjustmentFoils supplied to check calibration on siteIdeal for cold surfaces and underwater useSmall and portable with an accuracy ±5%The “V” grooved base, ideal for pipeline inspectionAvailable in either Metric or Imperial versions, the Elcometer 211 measures coatings up to 6mm (250mils)
-
Product
Strain Gauge Sensor
ZET 7010
-
Digital strain gauge ZET 7010 is designed for measuring relative deformation using primary transducers based on strain sensors. This can be strain-gauge transducers, torque sensors or separate strain-gauge transducers connected via bridge or half-bridge circuit.
-
Product
Needle Microprobe
MT-29/3HT
-
Fast-response 29 gauge needle probe, (needle length is 3 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
-
Product
Coating Thickness Gauge
-
Dalian Taijia Technology Co.,Ltd
In built probe(s)● Operating principle: magnetic induction/eddy current (F/NF)● Measuring range:0-1250um/0-50mil● Resolution; 0.1/1● Accuracy: ±1-3%n or ±2.5um● Min. measuring area: 6mm● Min. sample thickness: 0.3mm● Battery indicator: low battery indicator● Metric/ imperial: convertible● Power supply: 4x1.5V AAA(UM-4)battery● Auto power off● Operating conditions:0-+45℃(32℉-104℉),≤90%RH● Dimensions: 126x65x27mm● Weight: 81g(not including battery)● Optional accessories:● other range 0-200um to 15000um● RS-232C cable & software: 1.USB adaptor for RS-232C 2.Bluetooth interface
-
Product
Contactless Wafer Geometry Gauge
MX 20x series
-
The E+H geometry gauges are based on two heavy plates mounted parallel to each other. Embedded in the plate are a set of capacitive distance sensors. The wafer will be moved manual or automatically between the plates and measured without any movement.
-
Product
Pneumatic Comparator
-
Huaxin Instrument (Beijing) Co., Ltd
The vacuum pressure comparator is fitted with a differential pressure port that enables connection of gauges under test by hose.
-
Product
Thickness Meters
-
Choose from a variety of thickness meter, mil gage or paint meter products used for the non-destructive measurement of nonmagnetic coating, insulating layer and dry film thickness (DFT) on ferrous and / or non-ferrous metal substrates such as steel and aluminum. Explore PCE Instruments' selection of accurate, affordable thickness meter, coating thickness gauge, surface testing and film gauge devices used for automotive paint inspection, material testing and manufacturing quality control applications.
-
Product
Piezo Vacuum Gauge
HVG-2020A
-
Gas Composition Independent!The HVG-2020A vacuum gauge from Teledyne Hastings is a media-isolated, gas composition independent, piezoresistive instrument that provides accurate pressure measurement throughout the rough vacuum region.The HVG-2020A is easy to install, and the optional display provides the users with several different views, or modes of operation. The HVG-2020A is very flexible and can provide both analog and digital output to easily integrate into process control. A wide variety of linear analog output signals may be selected. This makes the HVG-2020A an excellent choice to replace more expensive capacitance manometers. Digital output can include RS232 and RS485 via a small jack on the top of the instrument. A USB connection is also available on many models which makes connection and operation very easy. Free Windows data acquisition software for data logging is available for the HVG-2020A.
-
Product
Magnetostrictive Level Gauge
HR9200
-
HighReach Measuring & Controlling System Co.,Ltd
The HR9200 magnetostrictive level gauge is a new generation of level gauge developed by the company using magnetostrictive principle combined with advanced digital and analog circuits. The product has high measurement accuracy, stable and reliable operation, and can be displayed on-site by liquid crystal meter It has compact structure, simple installation, strong resistance to power supply interference and environmental interference, and has great flexibility in use and strong environmental applicability.
-
Product
Primary Standards
-
Primary standards (often also referred to as mechanical dead-weight testers, pressure balances or primary pressure standards) are the most accurate reference instruments for pressure. Their functional principle is based on the physical principle of pressure = force/area. Mass pieces placed on the top of a piston-cylinder system are the source of a precisely defined force. By producing a certain (counter) pressure inside the primary standard an equilibrium is achieved: the mass pieces, including the free-running piston of the piston-cylinder system, are floating, which will lead to a very accurate pressure at the test port which measured through piston gauge technology.
-
Product
Manometers
-
Test Products International, Inc.
Single input vacuum gauge. 12,000 to 15 micron measurement range. 300 PSI over pressure. A safer instrument for your job.
-
Product
Digital Force Gauge
-
*Compact and light weight*3-way power supply*Display hold function is equipped*Easy zero adjustment function*Automatic recognition of the type of sensor*Judgment function (Hi&Low) is equipped
-
Product
Custom Gauging
-
As the world’s leading bore gauge manufacturer, Bowers Group has also earned a reputation for manufacturing custom heads for non-standard applications.
-
Product
Automotive Fuel Injector Pulser and Testing Tool
Wow
-
Automotive Diagnostics and Publishing
Developed to perform fuel injector flow testing, injector cleaning and pulse width general injector health determination, like pintle opening, binding and weak springs. But most of all, to perform accurate fuel flow tests using the pulser and your fuel gauge. The unit can handle all and any fuel injector in the industry. It can generate 5, 10 and 15 mSec or milli-second pulses and can also give you 1, 2, 4, 10 or continuous pulses.
