Motor Rotation
See Also: Motor Rotation Testers, Tachometers, Phase Rotation
-
Product
Rotating Rack Ovens
-
Based on our PH temperature ovens, these models incorporate a rotating specimen rack and are especially designed for accelerated heat deterioration testing of rubbers and plastics including polyesters and vinyl.
-
Product
Small Engine AC Motoring Dynamometers
-
SAKOR Technologies developed its new Small Engine AC Motoring Dynamometer specifically to meet the needs of engine manufacturers who must now comply with engine testing procedures required by new emission standards contained in 40 CFR Part 1065. These new requirements apply to almost every kind of small internal engine, including those in handheld power tools and lawn and garden tools.
-
Product
Motor Stator Tester
DZ900
-
Shanghai Aoboor Electric Co., Ltd.
Applicable to electrical properties test of stators of y-type three-phase motors.
-
Product
Brushless/Servo/Stepper Motor Tester
-
Shanghai Aoboor Electric Co., Ltd.
Applicable to brusheless, servo,stepper motor performance test.
-
Product
Rotating Bolthole Scanners
Nortec
-
Olympus extensive line of high performance eddy current scanners is available for use with Nortec Eddy Current Flaw Detectors. With a wide range of features consisting of speed ranges from 600 to 3000 rpm, frequency ranges from 100 Hz to 6 MHz, multiple connector types, and multiple probe types, our scanners offer a full range of application solutions.
-
Product
Digital Rotational Viscometer
-
Dongguan Kejian Instrument Co., Ltd.
Chemical industry, pharmaceutical industry, asphalt industry, building materials, paint, paint and ink, electronic industry, dairy industry, sauces and seasonings, adhesives industry.
-
Product
Motor Control Resistors
-
Post Glover specializes in motor control resistors — the most popular use of our resistors — for severe duty applications. Our resistors make it possible to start and stop extremely powerful electric motors — such as those on cranes, compressors, and pumps — with safety and precision.
-
Product
Motor Tester and Analyzer
ITIG
-
The iTIG III is the industry’s most advanced electric motor tester and winding analyzer. Bringing confidence to motor repair companies, industrial end users, OEMs, and manufacturers of rotating equipment, the iTIG III features over 20 high- and low-voltage tests including high frequency surge and partial discharge.Choose multiple tests to run automatically in a sequence or select single tests. Report results with the easiest to use instrument available. Manually operate voltage dial or set up for automatic operation. Carry the iTIG III in the field or use it as a benchtop device. Connect to an external portable power pack for testing up to 40kV. The iTIG III is the most versatile and easy-to-use tester available.
-
Product
Rotating Telemetry Systems
2100B Series
-
Advanced Telemetrics International
Are ideal for transmitting coupled data signals from sensors, which are mounted on rotating shafts or machinery to a stationary receiver.
-
Product
Motors
-
When your application demands ultra-precise positioning and high throughput, trust Aerotech’s motor expertise.
-
Product
Linear Vibration Motor Aging Unit
BK2019A
-
The BK2019A Linear Vibration Motor Aging Test System was designed to test your linear vibration motors for long term reliability. It can test 20 DUT’s at one time and you can stack them easily so you can test hundreds of DUT’s simultaneously in a small space. This is a great machine to ensure your product will do its job for it's expected life.
-
Product
MDA 8000HD Motor Drive Analyzers
MDA 8000HD Series
Analyzer
The Motor Drive Analyzer is built on an 8 channel, 12-bit resolution oscilloscope platform. It acquires any signal and performs three-phase electrical and mechanical power calculations. It provides complete power section and embedded control test coverage.
-
Product
Linear Motor Tester Lite
BK2019B
-
With the BK2019B, you can test for open/short circuits, operating current and even vibration level. Because it has only one purpose, it is very easy to set up and use and it's so small it can fit into the average briefcase.
-
Product
Brushed DC Motor Drivers
-
ST’s STSPIN motor drivers for brushed DC motors integrate a dual current control core and a dual full-bridge power stage to drive two brushed DC motors.
-
Product
Inductive Motor Control
-
The inductive motor control position sensor family detects the electrical position within one pole-pair of a rotating shaft and can be used for the motor commutation of a brush-less DC (BLDC) motor. Based on the inductive sensor technology, this family measures the coupling between an excitation coil (TX) and two receiver coils (RX) via a rotating target. The coils are executed as printed circuit coils and the rotating target is a simple punched metal part. With the correct layout of the coils and the target, both synchronized to the number of pole-pair count of the motor, the IC output is proportional to the electrical angular position within one pole-pair segment with increased resolution and high performance of only 0.3° electrical INL!
-
Product
Phase Rotation Meter
PCE-PI 1
-
The digital phase rotation meter PCE-PI 10 is used to determine the direction of rotation of 3-phase voltage networks. Furthermore, the phase rotation meter is able to measure voltages up to 600V AC / DC. The rotating field direction is important for machines and plants.
-
Product
Saluki SFS-2000 Fusion Splicer (4 motors)
-
SFS-2000 series is the new standard 4 motors fusion splicer. Light Weight, Touch Screen, Friendly UI, Fast Fusion and Heating, makes it very popular and hot.* 7s fast splicing, 14s highly efficient heating* 320/88 times image magnification, 5mm fusing for ultra-short cleave length* 10000 groups of fusion records storage* 300 groups of splice modes, 100 groups of heating modes* 220 counts of splicing and heating cycles with build-in 6800mAh Li-on battery
-
Product
High Precision Rotation Luminaire Goniospectroradiometer
LSG-1800BCCD
-
LSG-1800BCCD Goniospectroradiometer is high precision automatic goniophotometric instrument for luminous intensity distribution measurements with facility for turning the light source. The LSG-1800BCCD can do the spatial CCT test when do the intensity distribution test. It is for industrial laboratory measurements the photometric data of luminaires such as LED luminaries, HID lamps, fluorescent lamps and so on.
-
Product
Motor Test for Electric Scooters
-
*The performance data of electric motors, in the majority of all cases, is performed by a brake test. Power input is calculated from current and voltage. Torque and power output are measured with a brake. It is important to reach, for each point, a persistent temperature. In case of large outer rotor BLDC motors, which are usually used for electric scooters, this traditional procedure may take many hours to complete, and is very complicated. *For several years, an innovative motor tester of MEA Testing Systems Ltd. is on the market. This testing system avoids any temperature confusion by testing a motor at constant temperature over the entire speed range. The test procedure is very fast, and gives the full load performances, including PWM current, voltage, torque, and driver efficiency, from stall up to no load. *During the test procedure, the motor is freely accelerated from stall to no load speed. The load of the motor is only the predetermined inertia of the rotor. From the moment of inertia and the acceleration, the torque of the motor is calculated and, also, the power output over the whole speed is given. Since the entire measuring time, depending on the motor size, is usually less than one second, the motor has no time to warm up. It remains at room temperature.
-
Product
High Rotational Speed Measurement Handheld Digital Tachometer
HR-6800
-
The HR-6800 is a non-contact type handheld digital tachometer, which can measure the high speed rotational speed at Max. 999,990 r/min with high accuracy.
-
Product
Dynamic Electric Motor Analyzers
-
Baker's dynamic motor test and monitoring instruments are built to conduct condition monitoring tests of motors and generators from a Motor Control Centre (MCC), or through a Baker EP1000 connection unit. The Baker EXP4000 dynamic motor analyser is a low-voltage, AC- and battery-operated instrument that test motors and generators while they are in operation. The EXP4000 provides health and performance data on the motor, the motor's load, and incoming power to assess motor performance and suitability in context of the entire machine system it supports.
-
Product
Stator Testing System for EV Motor
EVT531
-
Shanghai Dean Electrical Co., Ltd
To meet the standard test projects requirement of the international companiesTo control and analysis the programs will reduce the human careless and misjudgmentEasy to edit environment and easy to learnIt can test multiple sets of DUTs simultaneouslyWhen there are several DUTs are tested, it could identify the undesirable sets individuallyThe Impulse/Surge with waveform comparison is a non-destructive analysisPolarity testMaximum saved files will be up to 100 setsIt provides the password functionSpeeding test could save time and improve efficiencyChinese and English pages can be arbitrarily switched
-
Product
Battery Pack Rotate Test Device
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Battery Pack Rotate Test Device Single storage cell safety testTest object: Battery storage pack or systemRotate the battery pack 360°around X axis with rotation speed of 6°/s; secondly rotate it 90°,180°,270°,360°,and remain for one hour after each move. Then stop and observe for 2 hours.Rotate the batter pack 360°around Y axis with rotation speed of 6°/s; secondly rotate it 90°,180°,270°,360°,and remain for one hour after each move. Then stop and observe for 2 hours.Accept standard: Battery pack or system has no electrolyte leakage, no rupture at case, no fire nor explosion. And remain the connection reliable, the structure intact, the insulation resistance value not less than 100 Omega /v.
-
Product
AC Motor Tester
JK115
-
Shanghai Aoboor Electric Co., Ltd.
Applicable to electrical performance test of single-speed, multiple-speed single-phase induction motors.
-
Product
Stepper Motor Controller for PCI
PCI322
-
The PCI322 Intelligent Stepper Motor Controller is designed to drive external amplifiers. This is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead. The local processor handles all high-level commands to provide maximum control for both straightforward as very complex applications
-
Product
Motors & Actuators
-
Our precision linear and rotary Voice Coil Actuators (VCAs) and Brushless DC Motors (BLDCs) produce, sense and control motion in high precision and high accuracy machinery. We also offer a series of VCA Developer's Kits that are easy to set-up and use without needing to specify a complete control system.
-
Product
4-Axis Stepping And Servo Motor Control Universal PCI Card
PCI-1240U
-
Independent 4-axis motion controlHand wheel and jog function2/3-axis linear interpolation function2-axis circular interpolation functionContinuous interpolation functionProgrammable T/S-curve acceleration/deceleration rateUp to 4 MPPS output for each axisTwo pulse output types: CW/CCW or Pulse/DirectionUp to 1 MHz encoder input for each axisTwo encoder pulse input types: A/B phase or Up/DownConstant speed controlPosition management and software limit switch functionBoardID™ switch
-
Product
Motor Testers
-
Changzhou Chanlon Electronic Technology Co., Ltd.
This machine is applied to test steel casing motor such as pump, fan, air-condition motor, mower, paper shredder and refrigerator etc. Its LCD shows all technical data which obtained by industrial control computer, which check and verify the quality of testing stator.
-
Product
Motor Winding Ohmmeter
RMO-M Series
-
The motor/generator winding resistance test is used to identify open windings, shorts between two windings, short to grounds, connection mistakes or shorted turns. This non-invasive test of winding resistance helps to pinpoint problems regarding windings in stator or rotor part of an electrical machine. Additionally, motor winding ohmmeter has the capability of performing heat run test which will show a change in windings resistance with an increase of temperature.The RMO-M series is designed as an ideal aid in preventive maintenance of electrical motors and generators. They are powerful (up to 100A of test current), portable (8 kg) and generate DC current which is completely ripple-free. This makes measurement very precise with 0,1% accuracy.Three voltage channels make measurement very easy since it is possible to obtain a value of all three winding resistances in one measurement
-
Product
Rack - Rotatable Arm for Peripheral Devices
OTP2-Modul-Nr041
-
The module is for mounting on a rack, such as the midi or maxi rack. The extension of the module can create new possibilities for your test system.
