Discrete I/O
-
Product
3U OpenVPX Ethernet Switch and Multifunction I/O Board
68G5E
Multifunction I/O
The 68G5E is a 3U OpenVPX board that is configured with an Ethernet Switch module (choose the ES1, 12-Port GbE Cu legacy unmanaged Ethernet Switch, or the ES2 16-Port Cu GbE managed Ethernet Switch with optional 4x 10GBASE-SR 850 nm multimode Fiber Optic interface) and provides additional support for one NAI smart I/O and Communications function module. Uniquely designed, the 68G5E provides ‘independent’ Ethernet Switch capabilities and can operate as a MFIO board end point with access via the 1 x1 PCIe and/or 1x 10/100 Ethernet motherboard Control Port which hosts the NAI Ethernet Protocol Server/Listener application for direct GbE MFIO control. Ideally suited for rugged Mil-Aero applications, the 68G5E delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
Digitaler I/O Mit 16 Kanälen
MDS
-
The static driver sensor module (MDS) is used to replace existing TS02 from previous MTS test systems. The possible pin extension allows to replace the systems MTS 200/210 (4 UCB with 4 MDS = 256 pins). A maximum of 1,024 MDS pins can be realized on the current MTS systems. Up to 4 MDS modules can be connected to one UCB (UCB03 or higher).
-
Product
PCIe Fast Digital Waveform Acquisition/Pattern Generator - 32 Digital I/O Channels, 1 kS/s up to 125 MS/s Sampling Speed
M2P.7515-X4
Digital Waveform
The M2p.75xx series of fast digital I/O cards allow to acquire or replay digital patterns with a programmable speed of up to 125 MS/s. The direction can be switched by software between input (digital data acquisition) and output (digital pattern generation). The on-board memory of 1 GByte can be completely used for digital pattern. Furthermore the on-board memory can be switched to a FIFO buffer allowing to continuously stream data in either output or input direction.
-
Product
FMC Expansion I/O Module.
SI-MOD32xx
-
The SI-MOD32xx is a family of high resolution, FMC form factor, high channel count multi function data acquisition and control modules that plug into any SI-DSP or FPGA carrier card.
-
Product
PCIe/104 OneBank FPGA I/O Board
EMC²-7A100
-
Sundance Multiprocessor Technology Ltd.
The EMC2-7A100 can use commercial, industrial or automotive graded Artix-7 FPGAs and is complimented with 1Gbyte of DDR3 local storage, 32Mbytes of Flash memory for storage/configurations and has 68x free differential I/O pins which are routed to a VITA57.1 FMC-LPC high-speed connector for bespoke interfaces.
-
Product
CPCI Advanced Compute And IO Board
-
Advanced Compute & IO Board is high end Microprocessor based Mixed Input & output Board. It is suitable for high speed Data Acquisition, Simulation, ATE applications. This board have digital I/O signals, analog I/O signals, USB, RS232, Ethernet interface and external bus interface. Board is well suitable for special type data acquisition & processing application. Board has high end FPGA which is used for automatic (Programmable) data acquisition and very useful high speed data acquisition. Board is based on CPCI architecture and can be used with CPCI or PXI backplane.
-
Product
Digital I/O Board, 32 Isolated I/O Channels, 24 V
PA1500
-
*16 input channels 24 V, incl. 14 interruptible*16 output channels, 24 V, 500 mA Optical isolation 1000 V*Input and output filters*Watchdog*3 timers/counters
-
Product
Multifunction I/O
526
-
Four 24-bit quadrature encoder inputsFour 16-bit analog outputsEight 16-bit analog inputsEight digital I/OSingle supply (5 V) input powerProgrammable interrupt timerVersatile watchdog timerxPC Target Real-time rapid prototyping softwareavailable through MathWorks
-
Product
Conduction Cooled XMC Interface Board with PCI Express Host Interface, Supporting up to 4 PX Modules, 2 RTx 5 Channel Modules, 1 Discrete & 1 Serial Module
EXC-8000ccXMC
-
The EXC-8000ccXMC is part of Excalibur’s 8000 family of multiprotocol boards. This conduction cooled XMC interface board has a PCI Express host interface and supports up to 4 Px modules, 2 RTx 5 channel modules, 1 Discrete and 1 Serial module. Due to the constraints of the XMC specification the modules are integrated onto the board itself rather than as physically separate modules.The EXC-8000ccXMC supports Direct Memory Access (DMA), which enables the board to access system memory for reading and writing independently of the computer’s CPU. This results in faster data transfer to and from modules that support DMA, with much less CPU overhead than when not using DMA.
-
Product
Isolated Digital I/O Card
PCIe-IDIO-24
-
This product is a x1 lane PCIe isolated digital input and FET output board with Change of State (COS) detection capabilities. In addition to the isolated signals, 8 (or 4) TTL/CMOS input/output pins are available, for your application’s convenience.
-
Product
LVDS Digital I/O with Kintex UltraScale FPGA - XMC
Model 71810
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Supports Xilinx Kintex Ultrascale FPGAs- Front panel digital I/O can be used as a status and control or data interface- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction-cooled versions available
-
Product
Receiver, G18, 18 Module For Discrete Wiring
310120101
Receiver
The lightweight and rugged 18 module Receiver provides a solution that will accommodate larger ATE chassis’ (PXI, VXI, SCXI). It allows immense versatility by affording space for up to an 18 slot PXI chassis.
-
Product
32-CH Discrete Input Modules
HSL-DI32-M-N/HSL-DI32-M-P
-
- Slave ID consumption: 2 consecutive from odd- "N" type for NPN sinking type sensor or dry contact; "P" type for PNP sourcing type sensor or wet contact- Photo couple isolation voltage: 2500 Vrms- Input impedance: 4.7 KΩ- Input current: ± 10 mA (Max), ± 12.5 mA (Peak)- Input voltage: ± 40 V (Max)- LED indicator: Power, Link and Input status- Power supply: +10 V to +30 VDC
-
Product
Benchtop Discrete Component Tester
Imapact 7BT
-
The 7BT Benchtop Discrete Component Tester is designed to test small signal and power semiconductor components in both single and multi-device packages or hybrids.. The 7BT automatic test system can be used in all test applications including incoming inspection, wafer probe, QC, engineering, production, final test, and high reliability.
-
Product
OpenVPX Ethernet I/O rear transition module.
EnsembleSeries™ RTM30P
-
*Companion Rear Transition Module for 3U OpenVPX Xeon® D-series process payloads (LDS3506)*Field Replacement Unit capability
-
Product
Automotive Power Discretes
-
ST offers a wide portfolio of automotive grade power discrete devices for reliable, robust and power-efficient automotive applications.
-
Product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 5V
APCIE-1564-5V
-
32 digital inputs, 5 V, isolated16 interruptible inputs32 digital outputs, 5 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
Product
16-bit, 100KHz, 16SE/8DIFF A/D Inputs; 4 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, All Isolated
CPCI-3120-16-4
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
3U 32-Bit 10-Slot CompactPCI PlusIO Hybrid Backplane with Rear I/O
cBP-3210PR
Backplane
The cBP-3210PR is a 3U 10-slot CompactPCI PlusIO hybrid backplane. Supports standard CompactPCI 3U height for 3U cPCI cards and PICMG 2.30 CompactPCI PlusIO. Supports hybrid function by having 5x cPCI standard slots and 4x CPCI-S.0 peripheral slots. The cBP-3213PR is ideally suited for safety controls in rail vehicles, management systems for controlling multiple SATA hard drives for large amounts of data or in RAID systems and for fast video and download processes.
-
Product
VME-Bus Synchro - Resolver LVDT I/O Cards
VB Series
-
Computer Conversions Corporation
The "VB Series" product lines contains VME compatible synchro/resolver converters and absolute encoder systems. These particular cards are ideal for any rotary motion and related process, control, or simulator type application with any VME compatible system.
-
Product
CB-37F-LP Unshielded, I/O Connector Block with 37-pin D-Sub
779353-01
Terminal Block
37-Pin, Female D-SUB to 40-Pin, Female Screw Terminal, Desktop Mount Terminal Block - The CB-37F-LP is an unshielded terminal block that provides access to DAQ devices with 37-pin connectors. The 37-pin, D-SUB connector makes this connector block ideal for direct mounting on the … DAQ device or connecting through a cable.
-
Product
CPCI Or PXI Analog IO Board
MS 1808
-
*Bus Interface*PCI Bus Interface, 6U Form Factor*Facility for Calibrating all Output channels*Hot Swap facility*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Rear I/O For VPX703, VPX RTM
VRT703A
-
The VRT703A is a 3U VPX Rear Transition Module providing I/O expansion for use with the VPX703. The VRT703A provides an easy access to the I/O ports routed to the P1 and P2 connectors of the VPX703. These includes dual PCIe x4, dual USB, RS-232 for both management and payload, dual 1553 ports, JTAG for CPU, dual GbE as well as mSATA socket for storage.
-
Product
PXI 32 Channel I/O, High Side Driver
40-413-001
Digital I/O
A 32 channel Digital I/O module with high output voltage and currentcapability and a dual variable threshold input. The 40-413 range is available in three configurations, a high side only (shown here), alow side only and a combined high and low side each capable of driving 2A loads. Eachoutput is fully protected against over-voltage, over-current and thermal overload,ensuring robust and reliable operation in the toughest test environments. For highside voltage driving the high side voltage source is supplied from an external voltagesource, permitting the module to drive high capacity loads without impacting thePXI chassis power supply.
-
Product
Digital I/O
IP-DIGITAL482
Digital I/O
IP-DIGITAL482 is a single-wide IndustryPack configured to maximize the number of digital I/O lines. The 48 lines are accessible as individual bits or as bytes. These lines may also be used for 8-bit and 16-bit I/O with handshake lines. IP-DIGITAL482 is a drop-in replacement for the IP-DIGITAL-48.
-
Product
NI-6584, 16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO
781290-03
Digital I/O Adapter
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter module for FlexRIO can be used to do real-time interfacing and analysis of RS485 and RS422 as well as other electrically compatible interfaces. The NI-6584 can sample digital waveforms at up to 100 MHz clock rates, has terminated and unterminated options, and full and half duplex configurations.
-
Product
LVDS Digital I/O with Virtex-6 FPGA - 6U VPX
Model 57610
-
- 32 or 64 bits of LVDS digital I/O- One or two LVDS clocks- One or two LVDS data valid- One or two LVDS data suspend- Supports LXT and SXT Virtex-6 FPGAS- One or two DMA controllers move data to and from system memory- Up to 2 or 4 GB of DDR3- PCI Express (Gen. 1 & 2) interface up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O to the carrier board- Ruggedized and conduction-cooled versions available
-
Product
iOS App Testing Services
-
To perform app testing, the approach for you to follow is creating a device lab, using UI automation services.
-
Product
3U CompactPCI Multi-Function I/O Board
CPCI-AD32
Multifunction I/O
The CPCI-AD32 is a 3U CompactPCI multi-function I/O board. The CPCI-AD32 offers 32 channels of 16 bit A/D, two 16 bit D/A, 16 digital I/O, counter / timers.There is a local 60 Mhz TMS320C31 DSP processor to supervise all the I/O activity. The DSP can be programmed by the end user to execute application specific code. The CPCI-AD32 is ideally suited for factory automation, automatic test equipment, test & measurement, and control systems.
-
Product
SCB-68A, Noise Rejecting, Shielded I/O Connector Block
782536-01
Terminal Block
68-Pin Female Screw Terminal to 68-Pin Female D-SUB, DIN-Rail, Shielded I/O Connector Terminal Block - The SCB-68A provides a shielded I/O connection for interfacing I/O signals to plug-in data acquisition devices with 68-pin connectors. This Terminal Block combines with shield cables to provide low-noise signal termination. The SCB-68A incorporates a completely redesigned mechanical enclosure with a magnetic removable lid, DIN-rail mount compatibility, and a resettable fuse. It is compatible with single- and dual-connector Multifunction I/O with 68-pin connectors. The SCB-68A also includes two general-purpose breadboard areas and an onboard cold-junction compensation sensor.
