-
Product
High Speed PXIe Digital IO Card - 32 Channels, Extendable up to 256 Channels in One Chassis
Model 33010
Digital I/O
Chroma 33010 is a high-density 100MHz PXIe digital IO card designed for characterizing, validating, and testing a variety of digital and mixed-signal ICs. Each IO Card consists of a Sequencer Pattern Generator (SQPG) and 32 Channels of fill ATE-like features. The 33010 IO card is expandable up to 356 channels. Some unique features of the 33010 include an on-board SQPG, per pin timing/levels/PMU/TFMU, multiple time domains, and multithreaded testing for complex IC testing. Each channel is also equipped with 64M vector memory, 16 timing sets with on-the-fly timing change, and per pin timing and frequency measurements up to 400 MHz.
-
Product
Radio Communication Tester
CMP180
-
The R&S®CMP180 radio communication tester is a future-proof, non-signaling testing solution for wireless devices in research and development, validation and production. Together with advanced frequency, bandwidth and RF capabilities, it enables testing of new wireless technologies such as Wi-Fi 6E, Wi-Fi 7, 5G NR FR1 and many more. Additionally, the doubled number of analyzers (2xVSA), generators (2xVSG) and RF ports (2x8) enable simultaneous measurements of technologies and devices in a VSA/VSG single-box tester.
-
Product
Assess Real-World Wi-Fi Performance
IxVeriWave
-
Keysight Network Applications and Security
Test and validate Wi-Fi performance of WLAN networks by recreating real-world scenarios.
-
Product
30 GHz Differential Probe with 2.92mm Interface
DH30-2.92MM
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
NI-9253, 50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module
785989-02
Current Input Module
50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module - The NI-9253 is an 8-channel analog input module for ComapctDAQ and CompactRIO systems. Each channel provides a ±20 mA input range and 24 bits of resolution at a 50 kS/s sample rate. The NI-9253 has several diagnostic features to ensure your system is operating nominally at all times with open channel detection, power supply detection, and configurable thresholds. The NI-9253 has eight LEDs to indicate the status of each channel and the power supply so that a user in the field can easily validate that the system is operating normally. The NI-9253 also features a number of programmable hardware filters. By choosing the specific Butterworth and comb filters for your application, you can significantly reduce the noise in your system.
-
Product
Remote Monitor Management Information Base
SNMP RMON MIB
-
For every control table in the MIB, create and delete rows with various combinations of SNMP requests (all variables in a single request throughall variables in individual requests).Determine which row of this table is modeling the ethernet interface connected to the agent (requires that we are using ethernet). Check that this is for the same interface discovered in the "interfaces" test. Check counters.Build a history control row pointing to the interface connected to the agent. Check validity and traffic reported.Test agent's ability to generate an alarm on an RMON variable, then on threshold condition. Test for support of alarms on failing events, and in the event of target variable vanishing.Set up agent to track hosts on the ethernet interface connected to the agent. Check that entry was added for Rmon device's own ethernet address.Generate various top N reports (hostTopN test) and check validity.Start a matrix capture and check that the src-dst and dst-src tables are in sync.Check a channel and check for event generation (filter test).Create a channel and start a capture. Test locking and wrapWhenFull operation.
-
Product
Automated Test System
-
Automated Test System is a production-ready solution that combines test software and various hardware for validation test in both manufacturing and R&D. The solution provides a high performance and cost-effective system based on National Instruments technology.
-
Product
Power modules
-
G.R.A.S. Sound & Vibration A/S
It provides polarization voltage for the transducer, ensuring that the microphone gets the charging voltage it needs.It provides supply voltage for the microphone preamplifier. The preamplifier acts as a unity gain impedance converter. It provides a certain amount of line drive capability by providing a low output impedance and output current, making it possible to transmit the signal from the transducer to the Power Module without significant degradation.A power module can provide amplification or attenuation to the signal, thus making it possible to fine tune the measurement chain to the signals being measured and the hardware being used.Selectable filters make it possible to exclude unwanted noise from the measurement, e.g. wind induced noise from outdoor measurements.Overload detection makes it possible to validate the measurements and is a useful tool in monitoring setups.When a Power Module with gain is used, you can use longer cables because of the power module's ability to deliver current.A Power module introduces electrical isolation
-
Product
Load Simulator
Simulator
The load system is intended for testing satellite power supply systems; due to the integration with a solar array simulator and a battery simulator, it can perform validation and commissioning of satellite power supplies. The system is equipped with regenerative electronic loads and customer-specific high-power switching matrices for routing the DUT channels to the relevant loads. The individual voltages and currents for each channel can be read back via a Keysight Technologies switch mainframe.The system is equipped with high electrical power; its loads are capable of feeding the energy back into the power grid.
-
Product
High Speed Communication Board
MS 1712
-
- 12 Channel RS422 Standard Communication interface- 4 Channel Configurable Manchester Bi-Phase Signal communications- 4MBPS configurable baud rate- VIRTEX4 FPGA based design- Hardware Frame formation- Hardware Data validation with START & END frame identification and Checksum calculation for RS422 communication- 1MB DPRAM for PCI interface- Separate set of FIFO's for Transmit and Receive channel- 16 Channels data recording through CF (Compact Flash Storage - Capacity up to 8Gbyte) up to 30min @ 2Mb/sec- Online download through USB interface- Driver interface for Windows2000/XP/VISTA and LINUX OS- 6U size cPCI Board- Hot Swap facility is provided for the live Insertion and removing of the board- 12 RS422 channels in front panel interface using two 25-pin D-Type connector
-
Product
GC Analyzers
-
Agilent’s GC Analyzer portfolio can combine multiple methods into a single system, with proven results, and significantly reduce time required from system arrival to final calibration and validation. With our preconfigured gas chromatograph hardware and method-specific separation tools, you can spend more time focusing on sample processing than on method and system development. Our specific GC Analyzer solutions provide the components and specifications to quickly install new methods for a fast return on investment in various application areas, such as environmental, gas impurities, forensics, pharmaceuticals, dissolved gas, energy, and chemical applications.
-
Product
UVC Light Meters & Detectors
-
International Light Technologies
If you are using a UVC light-based disinfection system you are probably scrambling to deploy tools to combat the COVID-19 outbreak. Increasingly facilities are looking to disinfect everything including air, surfaces, instruments, and personal protective equipment (PPE) using UV-C light. Verifying the intensity of the light, or dose, reaching the target is a critical step in validating that the correct UV dose is being applied to ensure proper decontamination.
-
Product
1Platform
-
Get full control over your Proof of Concept (PoC) and Testing & Validating from start to finish and deploying in production and monitor with the 1TX 1Platform. Bring order and simplicity to complex PoCs by managing multiple stakeholders and vendors with a single, secure platform.
-
Product
Interoperability Testing
-
Underwriters Laboratories Inc.
Leverage our expertise to validate that your product not only works as expected with all other relevant devices but also conforms to all appropriate standards and technology platforms. We do this by testing products in real-world scenarios. We are an approved testing laboratory for many IoT and wireless standards bodies, such as Bluetooth SIG, Thread Group, Wireless and Zigbee Alliance, and are actively engaged with key players in 5G. We test interoperability across many industries including appliances, building systems, consumer electronics and vehicles.
-
Product
ContactLAB Tester
-
The ContactLAB test platform provides fully configurable reader signal emulation for validation of ISO 7816 contact smart cards and Single Wire Protocol (SWP) USIM for NFC enabled mobile handsets.
-
Product
DDR5 Protocol Debug And Analysis Solution
U4970A
-
The DDR5 solution bundle provides a systemized hardware, probing, and software solution for DDR / 2 / 3 / 4 / 5 protocol debug, compliance validation, and analysis.
-
Product
Small-fiber Test
Q-Sense
-
Q-Sense offers a scientifically validated measure of warm, cooland heat-pain thermal sensory thresholds, all clinically usefuldeterminants in the evaluation of neuropathic pain, diabeticneuropathy, chemotherapeutic and other small-fiber neuropathies.
-
Product
OSFP 800G
-
OSFP800 has emerged as a leading standard to drive the development of 800G ecosystem. The MultiLane OSFP800 development kit is an essential tool to ensure the validity of your OSFP800 products. The module compliance board (MCB) is used to test transceivers, AOCs, active cables and DACs, while the host compliance board (HCB) enables the testing of system host ports. The loopback modules (LB) provide an economical way to test thermal capacity and signal integrity of system host ports at every stage of the process: R&D validation, production testing, and field testing.
-
Product
Rechargeable Accumulator for VES equipments
P100-2-N
-
A valid and ecological alternative to old 90V battery, P-100-2-N represents a renewable energy source for Vertical Electrical Soundings (VES). More accumulators can be connected in series to obtain up to 1000V.P-100-2-N is compatible with all PASI earth resistivity meters.
-
Product
Dynacell Load Cells
2527 Series
-
Dynacell is the world's first truly dynamic load cell, designed from the outset for measuring dynamic loads. Dynacell introduces the following advantages: *Reduces dynamic load errors which can be a significant percentage of reading*Increases productivity by allowing higher frequency operation while maintaining test validity *Improvements such as doubling the frequency are common
-
Product
Correlation Analysis
-
EDM Modal Correlation Analysis allows the user to correlate two modal models; EMA and/or FEA models. Comparing the experimental data with that acquired through finite element analysis helps in validating the test results. Users can import the geometry model and mode shape data from FEA or EMA software.
-
Product
ICT Tester
-
Adapter design, assembly and validation for Agilent, Keysight, HP, Checksum, Spea. Preparing and debugging ICT scripts. ISP Programming Integration. Integration of edge scan testing, Jest testing, digital testing, semi-functional testing, IC programming, FINN probes, and more
-
Product
WaveMaster Oscilloscope, 8 GHz Bandwidth, 4 Input Channels, 40 GS/s Max Sample Rate
WaveMaster 808Zi-B
Oscilloscope
Up to 20 GHz bandwidth and 80 GS/s sample rate.The most advanced oscilloscope user interface.The industry’s only true hardware 14.1 Gb/s serial trigger.Low Jitter Measurement Floor and exceptional timebase stability.Comprehensive set of serial data analysis, debug, validation and compliance tools.Integrated 50 Ω and 1 MΩ inputs for true connection and probing flexibility.Integrated standard and custom measurements and math functions for unrivaled analysis capability.Multi-lane serial data eye, jitter and crosstalk analysis.Real-time de-embedding, emulation, and equalization.
-
Product
Modal Analysis
-
The Modal Analysis package is part of m+p Analyzer, m+p international's dynamic signal analyzer for noise & vibration measurements and analysis. It provides a complete set of tools for observing, analysing and documenting the vibrational behaviour of machines and mechanical structures. Software modules are available for classical and operational modal analysis, shaker measurements (SIMO and MIMO) as well as for ODS, SDOF and MDOF analysis. A modal model validation module is also provided.
-
Product
Torque Carts
-
AIMCO offers torque carts for "lineside" or "point of use" tool validation and calibration. Our torque carts allow testing of tools on repeatable joint simulators and "in process" use on production joints, allowing users to identify process capability. There are multiple torque cart options:
-
Product
Bluetooth LE Protocol Qualification Tester
conformanceHarmony
-
The conformanceHarmony LE Tester is a robust testing solution recognized by the Bluetooth SIG as a validated test platform, focused on the qualification testing of products to the Bluetooth low energy specification. It is an integrated software/hardware test platform for Bluetooth protocol qualification testing that provides:
-
Product
Automotive Ethernet Tx Test Software 10M To 10Gbp
AE6920T
-
Unlike CAN, LIN, Automotive Ethernet demands rigorous compliance verification using test cases that cover transmitters (Tx), receivers (Rx), and harness/connector assemblies. To help you save time and effort, Keysight offers solutions that automate the testing and validation across Transmitter (Tx), Receiver (Rx), and the connections between Automotive Ethernet devices. Our engineers have invested thousands of hours in learning the standards and creating automated, repeatable compliance tests. These proven applications help you ensure proper test configuration and valid measurement results. Ultimately, you’ll have greater confidence that your device is compliant. Now available for data rates up to 10Gbps. The automotive Ethernet test solution AE6900T offers hardware and accessories to make sure you have all of the components you need to get up and running quickly.
-
Product
Network Infrastructure Testing
Xena VulcanBay
-
Xena Networks’ VulcanBay is a scalable Gigabit TCP test chassis that offers extreme performance for stateful traffic load testing, analysis and characterizing of Ethernet equipment and network infrastructure. It supports 1/2.5/5/10/25/40GE interfaces and can be used for simulating millions of real-world end-user environments to test and validate infrastructure, a single device, or an entire system.
-
Product
Fluids
-
Computational Fluid Dynamics (CFD) Simulation Software. Ansys computational fluid dynamics (CFD) products are for engineers who need to make better, faster decisions. Our CFD simulation products have been validated and are highly regarded for their superior computing power and accurate results. Reduce development time and efforts while improving your product’s performance and safety.
-
Product
PCIe to SD 3.0 M.2 Module
-
The M.2 module is based on Artix-7 FPGA that provides bridging features between PCIe and SD3.0 units to validate different memory densities of micro-SD card. For host processor communication, the module is designed with 2-Lane PCIe Gen 2.0 interfaces. The module presents compact design, flexibility, and consumes low power. Since PCIe is backward compatible with the earlier version the user can integrate into existing systems with ease. The interface towards the SD card is realized by the SD protocol implemented in the FPGA.
