-
Product
Mezzanine System
5047
System
The 5047 provides breakout of all ECM signals for debug, design validation and development. Plated through holes on the PCB allow soldering of probe wires to IO, Data, Power and Serial Identification signals. LEDs indicate presence of 3V, 5V, +12V, -12V and Ground. Elevates the ECM module by 2 mm and saves wear on the ECM carrier board connectors. Since this is a debug too there is no serial identification circuit.
-
Product
Inductively Coupled Plasma Mass Spectrometer
ICPMS-2030
-
With its newly developed collision cell and optimized internal structure, the ICPMS-2030 provides superior sensitivity. At the same time, thanks to the adoption of its proprietary mini-torch unit and provision of an Eco mode, the quantity of argon gas needed for analyses has been greatly reduced to the industry's lowest levels. As a result, low running costs are assured. The Development Assistant function of the software automatically sets the optimal analysis conditions for quantitative analysis. Then, after measurements are complete, the Diagnosis Assistant function automatically checks the validity of the necessary data. While reducing the burden on the user, the efficiency of analyses is enhanced and the reliability of the data can be increased. It complies with FDA 21 CFR Part 11.
-
Product
Datapaq Food Tracker System
-
Designed to measure and log true product and environmental temperatures and to deliver reliable, accurate HACCP process validation, the Datapaq Food Tracker System is the ideal solution for demanding food processing applications. The system is particularly suited to poultry, meat and seafood processing; commercial baking; frozen food production; commercial pasteurization and sterilization; and proving your compliance with HACCP regulations.
-
Product
ProxiLAB Quest Contactless Tester
-
Fully programmable card (PICC), reader (PCD) and NFC signal emulator for device characterization and protocol conformance verification. ProxiLAB Quest offers the performance and features required for full characterization and conformance validation of all 13.56 MHz contactless technologies, including the latest very high bit-rate evolutions. ProxiLAB Quest integrates with a variety of conformance certification solutions and test automation platforms.
-
Product
OSFP 800G
-
OSFP800 has emerged as a leading standard to drive the development of 800G ecosystem. The MultiLane OSFP800 development kit is an essential tool to ensure the validity of your OSFP800 products. The module compliance board (MCB) is used to test transceivers, AOCs, active cables and DACs, while the host compliance board (HCB) enables the testing of system host ports. The loopback modules (LB) provide an economical way to test thermal capacity and signal integrity of system host ports at every stage of the process: R&D validation, production testing, and field testing.
-
Product
Antenna Test Chamber for Automotive Radar
ATS1500C
-
The R&S®ATS1500C radar test chamber is a compact antenna test range (CATR), consisting of a gold-plated parabolic reflector and a two-axis positioner for 3D movements of the radar module. Combined with the R&S®AREG800A target simulator and other Rohde & Schwarz test and measuring instruments, it can be used for a variety of applications, including antenna characterization, module calibration, RF performance validation, interference testing or in-band compliance testing. The chamber is equipped with a universal feed antenna which gives access to both polarizations in parallel. Automated temperature testing over the range of -40 to 85°C is possible with an optional enclosure.
-
Product
ICT Tester
-
Adapter design, assembly and validation for Agilent, Keysight, HP, Checksum, Spea. Preparing and debugging ICT scripts. ISP Programming Integration. Integration of edge scan testing, Jest testing, digital testing, semi-functional testing, IC programming, FINN probes, and more
-
Product
Accelerated Mobile Pages (AMP) Testing Tool
-
Accelerated Mobile Pages (AMP) is a great way to make content on your website accessible in an extremely fast way. To help ensure that your AMP implementation is working as expected , Search Console now has an enhanced AMP testing tool. This testing tool is mobile-friendly and uses Google's live web-search infrastructure to analyze the AMP page with the real Googlebot. The tool tests the validity of the AMP markup as well as any structured data on the page. If issues are found, click on them to see details, and to have the line in the source-code highlighted. For valid AMP pages, we may also provide a link to a live preview of how this page may appear in Google's search results.
-
Product
Millimeter Wave Antenna Testing
-
If you are involved in antenna or system level design using mmWave or THz frequencies, then you understand the importance of dependable testing equipment. It may be that you are designing passive phase array or that you are designing a mmWave radar sensor system, but when it comes to validation of your design, simulation can only bring you so far. Phased array antennas have to be measured over the air (OTA) to ensure the radiation pattern of your design efficiently conducts energy in the right direction which is where the MilliBox comes in.
-
Product
Diagnostic Test System™
-
The original Teseda system for bench-top stimulus, test pattern debug, validation, device failure mode stimulation in-situ with other Failure Analysis lab equipment such as an EMMI, etc.
-
Product
Load Simulator
Simulator
The load system is intended for testing satellite power supply systems; due to the integration with a solar array simulator and a battery simulator, it can perform validation and commissioning of satellite power supplies. The system is equipped with regenerative electronic loads and customer-specific high-power switching matrices for routing the DUT channels to the relevant loads. The individual voltages and currents for each channel can be read back via a Keysight Technologies switch mainframe.The system is equipped with high electrical power; its loads are capable of feeding the energy back into the power grid.
-
Product
DH Series Solder-In Tip, 30 GHz BW, 3.5 Vpp Range
DH-SI
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Contactless Video Extensometers
-
Jinan Testing Equipment IE Corporation
Deformation measurement of samples during material testing with use of the Video extensometer MercuryRT allows applying multiple virtual probes (Movement Sensors)on markers and advanced image featuresto be tracked, including the natural pattern of the sample surfaces.The common resolution of standard system is within 500 nm and 5 m. The system fulfils class 0.5 or B-1 of classification according to ISO 9513 and ASTM E83. In certain camera use case, the system resolution reaches the level of 100 nm - 500 nm and system fulfils the class 0.2. The strain resolution can reach 10 microstrains. Material testing,Component testing ,FEA validation,Vibrography .
-
Product
Circuit Breaker Analyzer
CBAnalyzer
-
Simple operation requiring minimal trainingVery portable - it's a laptop or tablet pc running our Windows software programNo modification of the circuit breaker is requiredNo electrical connections are requiredRemoval of the circuit breaker from its mounting or cubicle is not requiredTesting can be performed during routine switchingData is easily transmitted over the internet to the users account where it is analyzed and compared with a known good profile (KGP) for that type of circuit breaker to determine: • Overall mechanical condition • Confirm maintenance intervals and lubrication • First trip testing data for arc flash compliance • Arc flash study validation checksPerform detailed analysis and store maintenance records using CBAnalyzer suite softwareAccess to the CBAnalyzer Account Manager which: • is where user accounts are created and each user's role is designated • provides access to your equipment database and test data archives • is where tests are synced • is where your equipment data is entered and stored • is required to use the CBAnalyzer software program
-
Product
Fluorescence Detector
RF-20A/RF-20Axs
-
The excellent basic performance of the Prominence series is further enhanced by the RF-20A/RF-20Axs fluorescence detectors, which offer world-class sensitivity, excellent ease of maintenance, and validation support functions. They support a wide range of applications from conventional analysis to high-performance analysis.
-
Product
Software
Battery Simulator
-
Chroma Systems Solutions, Inc.
Testing battery connected devices with an actual battery can either be cost or time prohibitive especially if multiple channels are required. Our Battery Simulation software is used to validate device functions during development in lieu of an actual battery or batteries. Automotive applications include motor drivers, OBC, DC-DC convertors or chargers, and products of DC bus.
-
Product
Managed Hub
HUB-5595
-
The HUB-5595 is a managed hub designed to operate with the Abaco Systems 5565 family of Reflective Memory real-time network products. The Reflective Memory hub can automatically bypass ports when it detects a loss of signal or the loss of valid synchronization patterns, allowing the other nodes in the network to remain operational.
-
Product
Safety Certified Controllers
HY-TTC 500 Family
-
The HY-TTC 500 family consists of high-end safety control units designed to satisfy upcoming needs for a wide range of high-end applications like construction and agricultural machines. The freely programmable high-end controllers with a powerful dual-core ARM Cortex®-R4 lockstep processor are protected by a compact, automotive-style housing suited for harsh environments. The safety controllers fulfill requirements up to SIL 2 (IEC 61508) / PL d (ISO 13849) / AgPLd (ISO 25119) – and can be programmed either in C or in CODESYS®. The safety certified CODESYS® Safety SIL 2 speeds up application validation of the certified controller significantly.
-
Product
MPEG Stream Monitor / Validator
TeleSight
-
Real-Time validation including video and audio bitstream conformance, video quality, bitrate, and audio levels Supports up to 20 streams simultaneously. View real-time playback of all input channels simultaneously or zoom in on one (real-time playback performance is dependant on machine, number of streams, and content). Mix variety of inputs types. Mix variety of supported MPEG formats.
-
Product
Hydrawedge
-
Through its patented technology, the Hydrawedge delivers test results without strain overshoot or strain rate deceleration, either one of which can reduce the validity of the simulation.
-
Product
Power modules
-
G.R.A.S. Sound & Vibration A/S
It provides polarization voltage for the transducer, ensuring that the microphone gets the charging voltage it needs.It provides supply voltage for the microphone preamplifier. The preamplifier acts as a unity gain impedance converter. It provides a certain amount of line drive capability by providing a low output impedance and output current, making it possible to transmit the signal from the transducer to the Power Module without significant degradation.A power module can provide amplification or attenuation to the signal, thus making it possible to fine tune the measurement chain to the signals being measured and the hardware being used.Selectable filters make it possible to exclude unwanted noise from the measurement, e.g. wind induced noise from outdoor measurements.Overload detection makes it possible to validate the measurements and is a useful tool in monitoring setups.When a Power Module with gain is used, you can use longer cables because of the power module's ability to deliver current.A Power module introduces electrical isolation
-
Product
Battery Simulator
Battery Simulator
The battery simulator is used for testing satellite power supplies and is used in combination with a Solar Array Simulator and load systems (consumer simulation) for the validation and commissioning of satellite power supplies. Loads and power supplies in the battery simulator are operated in combination to represent a 2-square function and to simulate both charging and discharging of the battery.
-
Product
Verification And Validation Services
-
Verification and validation services using innovative verification and validation techniques throughout the entire quality process for independent evaluation of performance and quality of product designed.
-
Product
Software Platform Bundle
Platform
The Software Platform Bundle provides the entire NI software portfolio for building any application. Develop applications in multiple environments, including LabVIEW Professional, LabWindows/CVI, and Measurement Studio. Extend the functionality of the LabVIEW development environment with all add-ons to perform code deployment, hardware integration, data analysis, and code validation. Build automated test systems with TestStand and real-time test systems with VeriStand.
-
Product
RRH/RRH Installation Tester
Integris 2000
-
Field installation teams for RRH s have a difficult task in validating the installation for proper cabling and RRH operation. This is because the BBU that connects to the RRH is not present during the RRH installation, making it impossible to truly know if the tower cabling and RRH have been installed properly.
-
Product
PCIe 5.0 Protocol Analyzer
P5552A
Protocol Analyzer
The Keysight P5552A PCIe 5.0 Protocol Analyzer introduces a new form factor that is easily deployable in the lab bench environment to enable deep protocol analysis of a PCIe system with unparallel signal integrity. Locate protocol errors or validate device operations by viewing data from the physical layer all through the transactional layer with ease.
-
Product
PXI-2536, 544-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-36
Matrix Switch Module
544-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2536 is a high-density 8x68 PXI matrix switch module that is ideal for routing low-power DC signals in validation test systems of mass produced devices such as semiconductor chips and printed circuit boards (PCBs). Featuring FET relays, the PXI‑2536 offers unlimited mechanical lifetime and switching speeds up to 50,000 crosspoints/s. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
SOP Managemen and Quality Management
arivis BM-Windream
-
BM-windream is the 21 CFR Part 11 compliant data and document management system for the pharmaceutical industry. It is based on the market leading windream document management system from windream GmbH, Bochum. In addition to our industry-specific modules, we have access to a series of tried and tested windream add-on modules from our partner network, e.g. for e-mail archiving, linking to ERP systems, CRM systems, knowledge management or scanning solutions. BM-windream provides a basis for your data and document management that can be validated at relatively low cost (configurable standard software complying with GAMP5) and is easy to use. Users access your documents using a virtual network drive in Windows Explorer, which means that little training is required. BM-windream provides a standardised user interface over the entire life cycle of a file, from creation to deletion. At all phases in this life cycle, a change history (audit trail) is recorded. BM-windream is suitable for handling all kinds of non-managed documents. BM-Flow integrates directly with BM-windream and provides the document management functions required for SOP management,manufacturing instructions etc. All general employees can then still access the documents using the familiar Windows Explorer, while those responsible for creating documents can also use the workflow interface in BM-Flow.
-
Product
Simulators (Gen II)
J1939
-
The Au SAE J1939 simulators (Gen II, includes V1.00A releases and V2.00A releases) can generate SAE J1939 signal for up to three controller applications (CA): Engine, ABS and Transmission. Au J1939 simulators are designed so easy to use, even product line operator and sales personal can use them without Controller Area Network training. Au J1939 simulator can run all by itself and doesn''t require complicate software settings or user''s knowledge and experience on Controller Area Network. It is widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration to product development and product validation.
-
Product
PXIe-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
780587-12
Signal Module
PXIe, 7-Channel, 10 A PXI Signal Insertion Switch Module—The PXIe‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
