Debug
See Also: Debuggers
-
Product
Multipurpose Debug Board
DB40 Debug Module
-
The DB40 Debug Card is designed for debugging of COM Express and PC/104 boards. It includes the following features: - Port 80/81 decoding for Power On Self Test (POST) via LPC - Interface to SPI Flash for BIOS update - Interface to Board Management Controller (BMC) for update - Power and Reset buttons and status LEDs The DB40 Debug card can only be used on products that have the appropriate FFC debug connector designed for this purpose. (Includes DB40 Debug Module, two 40-pin FFC cables, and 14-pin cable for SP100 DediProg USB to SPI programmer.)
-
Product
Debug Adapters
-
One thing is sure in the life of an embedded developer - your next microcontroller development board will be fitted with a different debug connector to the one used in your previous design.
-
Product
In-Line Debug Press
-
Use for DEBUG without having an In-Line TesterUse Standard 3070 Test System for DebugSupport In-Line Tester on current 3070Verify Form and FitSlides in and Out like on an actual In-Line System
-
Product
Debug probe for ARM Cortex processors
USB Multilink ACP
-
P&E’s USB Multilink ACP is a debug probe which allows a PC/laptop access to JTAG/SWD on ARM Cortex devices from several manufacturers (see complete list below). It connects between a USB port on a Windows machine and the standard debug connector on the target. The product photos to the left of this page show how the headers can be accessed by simply flipping open the plastic case. Ribbon cables suitable for a variety of architectures are included. By using the USB Multilink ACP, the user can take advantage of the debug mode to halt normal processor execution and use a PC to control the processor. The user can then directly control the target’s execution, read/write registers and memory values, debug code on the processor, and program internal or external FLASH memory devices.
-
Product
Debug Probes
J-Link and J-Trace
-
SEGGER Microcontroller GmbH & Co. KG
SEGGER J-Links are the most widely used line of debug probes available today. They've been proven for more than 10 years with over 250,000 units sold, including OEM versions and on-board solutions. This popularity stems from the unparalleled performance, extensive feature set, large number of supported CPUs, and compatibility with all popular development environments.
-
Product
LPDDR5 Protocol Debug And Analysis Solution
U4971A
-
The LPDDR5 Solution Bundle provides a systemized hardware, probing, and software solution for LPDDR / 2 / 3 / 4 / 5 protocol debug, compliance validation, and analysis.
-
Product
PXI Test System Dev, Debug & Monitor Software
InstrumentStudio
Test System
InstrumentStudio is free application software that provides an integrated approach to interactive PXI measurements. InstrumentStudio helps you to unify your display, export instrument configurations to code, and monitor and debug your automated test system. You can view data on unified displays with large, high-resolution monitors, and then capture multi-instrument screenshots and measurement results.
-
Product
Debug Probe
-
High-performance Debug Probe for embedded development with support for multiple target architectures.
-
Product
Multipurpose Debug Board For EC
DB30 x86 Debug Module
-
The DB30 x86 Debug Card is designed for debugging of COM Express modules with FFC (FlexFoil Cable) debug connector. It includes an 80 port for Power on and Self-test (POST) via I2C interface, interface to SPI Flash for BIOS update, interface to EC for Embedded Controller (EC) update, Power and Reset buttons, and Status LEDs and Test Point for various debug tests.
-
Product
Multipurpose Debug Board
DB40-HPC Debug Module
-
The DB40-HPC Debug Card is designed for debugging of COM-HPC modules with FFC (FlexFoil Cable) debug connector. It includes an 80 port for Power on and Self-test (POST) via I2C interface, interface to SPI Flash for BIOS update, interface to EC for Embedded Controller (EC) update, Power and Reset buttons, and Status LEDs and Test Point for various debug tests.
-
Product
WinSock Trace / Debug Utilities
SocktSpy
-
The Socket Spy programs are Trace/Debug utilities used for monitoring WINSOCK API references between an application and the Windows Sockets Dynamic Link Library. Socket Spy/16 operates under Windows 3.1 and is fully compatible with the WinSock Ver 1.1 standard.
-
Product
Hardware Debug Interface & Stand Alone Programmer
Cyclone PRO
-
P&E Microcomputer Systems' Cyclone PRO is an extremely flexible tool designed for in-circuit flash programming, debugging, and testing of Freescale HC08, HCS08, HC12, HC(S)12(X), and RS08 microcontrollers. Now featuring support for Freescale's ColdFire V1.
-
Product
Stand-Alone Programmer and Hardware Debug Interface
Cyclone MAX
-
Cyclone MAX is an extremely flexible tool designed for in-circuit flash programming, debugging, and testing of Freescale ColdFire V2/V3/V4, Power Architecture 5xx/8xx, Power Architecture 55xx/56xx (Nexus), and ARM (MAC7xxx) microcontrollers.
-
Product
Kernel Aware Debug
-
Kernel Awareness for RTXC Quadros gives the developer deep visibility into virtually every aspect of kernel activity during debugging. The popup windows allow you to view RTXC Quadros-specific objects in an easy-to-read fashion.
-
Product
Debug Hardware
-
To record your digital and analog signals, just press start. You can fill your entire computer’s memory with data so it is easy to capture lengthy or rare events.
-
Product
High Level Language Debugger and Emulator Tool
Universal Debug Engine
-
Programmierbare Logik & Systeme GmbH
With Universal Debug Engine (UDE®) PLS offers on top solutions for software development of systems-on-silicon including debug support for the 16 Bit and 32 Bit microcontrollers C16x, C166™, ST10F276, ST10F280, XC166, XC2000, XE166, XMC4500, C166S V2, SDA6000, TriCore™ from Infineon and STMicroelectronics, Power Architecture® MPC55xx, MPC560x, MPC563x, MPC57xx from NXP™, PowerPC PPC440SPe from AMCC, Power Architecture® SPC560, SPC563, SP574 from STMicroelectronics, ARM7™, ARM9™, ARM11™, Cortex™-M0, Cortex™-M0+, Cortex™-M3, Cortex™-M4, Cortex™-M7, Cortex™-R4, Cortex™-A8, Cortex™-A9, XScale™, SuperH™ SH-2A derivatives in a new multicore debug environment as well as technical support. The extensive feature list includes functions like: high speed and flexible target access via JTAG, cJTAG with OCDS L1, EmbeddedICE, OnCE, COP, DAP, DAP2, SWD support, OCDS L2 trace, MCDS trace, CoreSight™ trace, ETM trace, ETB trace, Nexus trace, ASC, SSC, 3Pin and CAN, in-system FLASH memory programming of FLASH / OTP with UDE MemTool, support of various RTOS, OSEK® and test automation tools.
-
Product
RTL debugger and viewer for Verilog and VHDL
RTLvision
-
RTLvision PRO provides easy RTL debugging and fast visualization of RTL code, so that engineers can easily understand, implement and optimize VHDL, Verilog or SystemVerilog code. Please check out the Demo Videos: Basic Features and Clock Tree Analyzer.
-
Product
16 Channels, 200MHz, 1 M Samples/Channel Buffer USB Logic Analyzer
La-Logic-16
-
The La-Logic-16 is a sophisticated PC-based logic analyzer. It captures at a maximum of 200Mhz on its 16 channels simultaneously into it?s deep 1M samples/channel buffer.It can also operate as a 16-channel pattern generator.It connects to the PC via the USB-port and does not require any external power. The package is complete with all accessories included to start debugging immediately.
-
Product
Microwave Switches
SMX-7XXX (Microwave)
Microwave Switch Module
The AMETEK VTI Instruments SMX-7000 Series of microwave switch cards extends functionality typically reserved for dedicated stand-alone systems into the PXIe from-factor. Single and dual slot configurations provide the ability to mix and match multiple switch configurations including SPDT, SP4T, SP6T and Transfer. Embedded virtual schematic control further simplifies setup and debugging allowing all relays to be engaged independent of application software and device drivers. Ideally suited for medium-to-high density automated test equipment (ATE), the SMX-7000 Series deliver uncompromised measurement integrity ideal for the most demanding aerospace, defense and communication applications.
-
Product
Boundary Scan / JTAG Test Development System
onTAP Development
-
The onTAP Development system will speed up your project development time and keep costs under control. These tools enable you to quickly and easily develop, run, and debug JTAG tests ranging from single JTAG chain applications to multiple JTAG chain applications with multi-die modules, merged sub-assemblies, and multi-drop configurations.
-
Product
A Serial Data Link Monitor for Windows
Listen
-
Listen is a Data Link monitor designed to assist debugging & troubleshooting serial communications links. Listen utilizes standard Windows COM port drivers to tap into RS-232 transmit signals for monitoring bi-directional communications between two devices.
-
Product
Wireless Functional Test Fixtures
-
Circuit Check’s wireless fixture technologies reduce debug time, simplify ECO’s and reduce maintenance. This allows for the highest test performance, ability to probe denser smaller targets and achieve ultra-high node counts. Higher density more complex circuit boards complicate testing requirements. Smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board (T-Board).
-
Product
DH Series QuickLink Adapter Kit with 3 x QL-SI Tips
DH-QL-3SI
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Extender Card
-
The IEEE extender card, referred to as board PWB1000281-03. Extender card to allow for testing and debugging of the chassis assembly. This board was originally an Intel design that Dynamic Engineering was authorized by Intel to re-create
-
Product
3U VPX Board
VP32004
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP32004 is a high-performance PC-based 3U VPX processor board developed by Linkedhope®. It supports 3rd Gen Intel Core series processor and Intel QM77 chipset. It supports up to 16GB of on-board DDR3 ECC memory and supports mSATA SSD. In order to ensure that VP32004 works stably in a strong shock and vibration environment. VP32004 provides rich I/O interface, including 2x SATA III channels, 2x 1000 Base-BX/T, 1x RS232 front debug serial port, 3x RS232/422/485 interfaces (BIOS configurable), 4x USB2.0 interface, 1x USB3.0 interface, 1x Mini-DisplayPort display interface, 1x rear VGA display interface, 1x PS/2 interface.The board provides a flexible PCIe bus interface to the backplane that supports multiple configurations and can be configured as 1 x8, 2 x4, 4 x2 PCIe. This feature makes it suitable for both distributed and centralized switching systems.
-
Product
PCI Express 4 M.2 Receiver Test Automation
N5991PM4A
-
The N5991PM4A is the receiver test automation software for bit error ratio testers, allowing you to test, debug and characterize PCI Express M.2 devices and hosts at 8 GT/s.
-
Product
High Performance Netlist Debugging and Netlist Viewing
-
GateVision PRO is the third generation of graphical gate-level netlist analyzers and netlist viewers from Concept Engineering. Please check out the Demo Video: Basic Features. Completely rewritten to run on modern 32/64bit platforms, GateVision PRO provides the designer of even the largest chips and SoCs with intuitive design navigation, netlist viewing, waveform viewing, logic cone extraction, interactive logic cone viewing for netlist debugging and design documentation.
-
Product
USB Modular Oscilloscope, 100 MHz, 2 Analog Channels
U2701A
Oscilloscope
100 MHz2 analog channelsMore accurate analysis of electronic designs with deep 32 Mpts memory and high 1 GSa/s sample rateSimple USB setup with plug and play capabilityGet the debug power you need with advanced triggering, automatic measurements, math functions including FFTs and moreQuick and easy measurement configuration and acquisition with bundled Keysight Measurement Manager (KMM) softwareDocument results more easily using the high speed USB 2.0 interface
-
Product
Infiniium V-Series Real-Time Oscilloscopes
V-Series
-
Bandwidth upgradability to 33 GHz for best investment protection Maximize eye height measurements with the least amount of noise contribution from the oscilloscope See the truest jitter performance of your design with the lowest 100 fs oscilloscope intrinsic jitter Debug some of your most difficult designs with the industry’s longest hardware serial trigger
-
Product
Systems Integration (SIL) Lab Data Acquisition
System
Bloomy’s SIL data system allows testing and simulation of every system component on the aircraft. The functionality of these complex integrated systems are fully tested, debugged, and verified safely in the lab prior to flight testing. This reduces cost and schedule for new aircraft. Bloomy has applied its expertise to multiple SILs.
