Debug
See Also: Debuggers
-
product
Wireless In-Circuit Test Fixtures
Higher density more complex circuit boards complicate testing requirements while smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in standard long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board or T-Board®. Circuit Check’s wireless fixture technologies reduce test program debug and maintenance times while easing the ECO process. Thus allowing for the higher level of test performance, the ability to probe smaller denser targets and achieve ultra-high node counts.
-
product
PCIe Carrier Board for SOM3
Solar Express 215 (SE215)
Sundance Multiprocessor Technology Ltd.
SE215 is a development board for Sundance SOM3 . It is a PCIe X1 Gen2 carrier card with one site for an SOM3. It offers USB JTAG and UART, through a micro USB connector, Display port and comes with a version of Display port IP core for SOM3 from Bitec DSP. The card provides Power GOOD and user LEDs for rapid debugging.
-
product
Oscilloscopes
Scientech Technologies Pvt. Ltd.
Oscilloscopes are essential tools for anyone designing, manufacturing or repairing electronics equipments. In today''s fast paced world, engineers need the best tools available to solve their measurement challenges quickly and accurately. Scientech Oscilloscopes are the key to meet today''s engineer measurement challenges. Today, Scientech Technologies is a prominent figure in the market as an Oscilloscopes manufacturer and supplier. It has built a big territory of oscilloscopes implementing all the newfangled techniques. These Oscilloscopes are the finest solution for quick analysis, faster debugging and testing of your newest designs. Scientech as an oscilloscope manufacturer has gifted researchers, professors and students with the first-rate model of scope for various test & measurements and laboratory experiments.
-
product
ESPI Analysis Application
TP601010
First released by Intel in June 2013, the Enhanced Serial Peripheral Interface (“eSPI”) is designed as a replacement for the Low Pin Count (“LPC”) bus. eSPI supports communication between Embedded Controller (EC), Baseboard Management Controller (BMC), Super-I/O (SIO) and Port-80 debug cards. eSPI was available in the Sky Lake chipset (2015) and is available in the Kaby Lake [current] chipset. Cannonlake will support eSPI and is slated for release the second half of 2017. Icelake is scheduled for release in 2019 and it will mark the first chipset when eSPI becomes mandatory.
-
product
Digital And Mixed Signal Oscilloscope
MSO/DPO70000 Series
The MSO/DPO70000 is one of the most advanced oscilloscopes in its class: enabling today’s engineer to see signals better with minimal noise, debug signal anomalies faster, reduce debug time, and utilize measurement and analysis tools for automated compliance testing and other verifications. In addition, the MSO/DPO70000 is perfect for analog/digital design and debug, data communications and high-speed serial communications. See how you can use the MSO/DPO70000 for your next project to find and analyze a wide range of mixed-signal anomalies.
-
product
DH Series High-Temperature Solder-In Tip, 16 GHz BW, 3.5 Vpp Range
DH-HITEMP
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
RF ATE Tester
ADIVIC MP5800/MP5806
MP5800 seamlessly upgrades your existing Chroma 3380, 3650 to RF ready ATE test solution, user friendly debug tools, IOT turnkey test solution.
-
product
VB-8054 , 4-Channel, 500 MHz Bandwidth VirtualBench All-in-One Instrument
785037-04
4-Channel, 500 MHz Bandwidth VirtualBench All-in-One Instrument—The VB‑8054 combines a four‑channel, 500 MHz mixed-signal oscilloscope with protocol analysis, an arbitrary waveform generator, a digital multimeter, a programmable DC power supply, and digital I/O into a single device that integrates with your PC or iPad. The VirtualBench all‑in‑one instrument is simple and convenient and results in more efficient circuit design, debugging, and validation. The included software provides an interactive way to view all your measurements on a single screen and can be updated for free with software releases over time to continually add functionality and value to your VirtualBench. VirtualBench also tightly integrates with LabVIEW software to enable programmatic control and automated test sequences.
-
product
Simulator for Test Driving of Drones & Robots
Aerial Informatics & Robotics Platform
The Aerial Informatics and Robotics platform solves for these two problems: the large data needs for training, and the ability to debug in a simulator. It will provide realistic simulation tools for designers and developers to seamlessly generate the copious amounts of training data they need. In addition, the platform leverages recent advances in physics and perception computation to create accurate, real-world simulations. Together, this realism, based on efficiently generated ground truth data, enables the study and execution of complex missions that might be time-consuming and/or risky in the real-world. For example, collisions in a simulator cost virtually nothing, yet provide actionable information for improving the design.
-
product
I2C/SPI Exerciser and Protocol Analyzer
PGY-I2C/SPI-EX-PD
Prodigy Technovations Pvt. Ltd.
I2C Protocol Analyzer and SPI Protocol Analyzer (PGY-I2C/SPI-EX-PD) are the Protocol Analyzers with multiple features to capture and debug communication between host and design under test. PGY-I2C/SPI-EX-PD is the leading instrument that enables the design and test engineers to test the respective I2C or SPI designs for its specifications by configuring the PGY-I2C/SPI-EX-PD as Master/Slave, generating I2C/SPI traffic and decoding the I2C/SPI protocol decode packets
-
product
Test & Programming Software
ScanExpress
The ScanExpress Family of boundary-scan software offers a fully integrated development environment that includes boundary-scan and at-speed functional test program generation, test program execution with advanced pin level diagnostics, interactive boundary-scan debugging, and in-System Programming (ISP) of devices such as Flash memory, serial EEPROMs, CPLDd, and FPGAs.
-
product
Boundary Scan / JTAG Test Development System
onTAP Development
The onTAP Development system will speed up your project development time and keep costs under control. These tools enable you to quickly and easily develop, run, and debug JTAG tests ranging from single JTAG chain applications to multiple JTAG chain applications with multi-die modules, merged sub-assemblies, and multi-drop configurations.
-
product
High Level Language Debugger and Emulator Tool
Universal Debug Engine
Programmierbare Logik & Systeme GmbH
With Universal Debug Engine (UDE®) PLS offers on top solutions for software development of systems-on-silicon including debug support for the 16 Bit and 32 Bit microcontrollers C16x, C166™, ST10F276, ST10F280, XC166, XC2000, XE166, XMC4500, C166S V2, SDA6000, TriCore™ from Infineon and STMicroelectronics, Power Architecture® MPC55xx, MPC560x, MPC563x, MPC57xx from NXP™, PowerPC PPC440SPe from AMCC, Power Architecture® SPC560, SPC563, SP574 from STMicroelectronics, ARM7™, ARM9™, ARM11™, Cortex™-M0, Cortex™-M0+, Cortex™-M3, Cortex™-M4, Cortex™-M7, Cortex™-R4, Cortex™-A8, Cortex™-A9, XScale™, SuperH™ SH-2A derivatives in a new multicore debug environment as well as technical support. The extensive feature list includes functions like: high speed and flexible target access via JTAG, cJTAG with OCDS L1, EmbeddedICE, OnCE, COP, DAP, DAP2, SWD support, OCDS L2 trace, MCDS trace, CoreSight™ trace, ETM trace, ETB trace, Nexus trace, ASC, SSC, 3Pin and CAN, in-system FLASH memory programming of FLASH / OTP with UDE MemTool, support of various RTOS, OSEK® and test automation tools.
-
product
VME Test Extender 3U/220mm J1
111EXT3122-11XX
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
Benchtop Automated Functional Test
midUTS
Combining bench-top portability with powerful automated test functionality, the midUTS is an extremely versatile yet cost-effective solution for your electronics functional test needs. Comprised of high-performance commercial-off-the-shelf (COTS) instruments, along with Bloomy’s medium-density signal-routing PCBAs, a built-in or USB-connected PC, and a pair of high-integrity, production-grade cables connected to an adjacent benchtop fixture, the midUTS can be used in engineering for PCBA bring up, as well as scaled to manufacturing to perform high-volume PCBA and sub-assembly functional testing. It is also ideal for depot diagnostic test, debug, and repair of field returns. The two mass-interconnected cables connect the midUTS to as many as 320 test points on the unit under test (UUT), supporting an extreme wide variety of products using bed-of-nails as well as cable-connected UUT test fixtures. Most importantly, the midUTS helps you automate sequences of functional tests using NI TestStand and the Bloomy EFT Module for TestStand. This ideal balance between powerful features and affordable cost allow you to automate earlier in the product development lifecycle, substantially increasing product quality and minimizing time-to-market!
-
product
VME Test Extender 6U/220mm Universal
110EXT6122-000X
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
cRIO-9047, 1.60 GHz Quad-Core CPU, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 8-Slot CompactRIO Controller
785621-01
1.60 GHz Quad-Core CPU, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 8-Slot CompactRIO Controller - The cRIO-9047 is a rugged, high-performance, customizable embedded controller that offers Intel Atom quad-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 70T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
product
The all-in-one data logger for the entire vehicle networking
PM-200
The PM-200 sets the bar considerably higher on the topic of safeguarding and troubleshooting vehicles. Bus systems such as CAN, CAN-FD, FlexRay™, LIN, MOST150 and Automotive Ethernet are logged at a data speed up of to 120 MB/s. SSD removable media allow for quick evaluation and distribution of the data. Various upgrade options enable configuration for any application. Flexibility, programmability and support from debugging protocols make it possible to meet the high demands of functionality and fleet tests as well as of test runs.
-
product
Logic Probes
Logic probes are used to analyze the logic states (high/true: logic 1 or low/false: logic 0) of digital signals. To verify and debug today’s high-speed, low-voltage digital signals, you need logic probes that can accurately acquire signals from a wide variety of electronic designs, while protecting signal fidelity. Tektronix logic analyzer probes contain a variety of connectivity options that are engineered to ensure that signal acquisition is a true reflection of your design's performance. Compare and learn more about Tektronix logic analyzer probe solutions below.
-
product
Logic Analyzer Probe
FS2521
The FS2521 is a logic analyzer probe used to test DDR4 SO-DIMM memory. When used with the triggering and analysis capabilities of Keysight’s U4164A logic analyzer modules, it gives the user an extremely effective tool for debugging, testing and verifying DDR4 SO-DIMMs. Now qualified at 3200MT/s
-
product
cRIO-9043, 1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 4-Slot CompactRIO Controller
785620-01
1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 4-Slot CompactRIO Controller - The cRIO-9043 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 160T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
product
6U VPX Extender Gen2
The VPX extender module is built to extend a 6U VPX module completely out of a chassis, providing access to all sides of the module for testing and debugging.
-
product
VB-8054, 4-Channel, 500 MHz Bandwidth VirtualBench All-in-One Instrument
785037-05
4-Channel, 500 MHz Bandwidth VirtualBench All-in-One Instrument—The VB‑8054 combines a four‑channel, 500 MHz mixed-signal oscilloscope with protocol analysis, an arbitrary waveform generator, a digital multimeter, a programmable DC power supply, and digital I/O into a single device that integrates with your PC or iPad. The VirtualBench all‑in‑one instrument is simple and convenient and results in more efficient circuit design, debugging, and validation. The included software provides an interactive way to view all your measurements on a single screen and can be updated for free with software releases over time to continually add functionality and value to your VirtualBench. VirtualBench also tightly integrates with LabVIEW software to enable programmatic control and automated test sequences.
-
product
Catena 1910 HSIC Tester
Catena 1910
The MCCI Catena 1910 HSIC USB Tester enables testing of HSIC Host or HSIC Device products. It can be used to exercise your product by operating as an active host or active device, while simultaneously capturing USB traffic for analysis. For test and validation of a final system, Passive Capture mode lets you debug and verify communication between your HSIC Host and HSIC Device,
-
product
T3AWG2K Series - 16-bit Dual Channel Arbitrary Waveform Generator
T3AWG2K Series
The T3AWG2K series consists of two affordable dual-channel arbitrary waveform generators, 16-bit vertical resolution, 6 Vpp output voltage (50Ω to 50Ω), 128 Mpts/ch memory, a maximum sampling rate of 600 MS/s and a maximum sine wave frequency of 150 MHz. The T3AWG2152-D mainframe adds 8 synchronized digital channels to the analog outputs, ideal for debugging and digital design validation.
-
product
Function Test and In-Circuit Test
CT350
ICT test points: max 2736 CAD Data import Automatic program generator Powerful debugging tools Test coverage analysis Paperless repair station Logging- and statistic functions Full graphical functions Panel and multisite tests Fast adapter exchange High Pin Count-Interface On table optional usable shelf part.
-
product
25 GHz Differential Probe with 2.92mm Interface
DH25-2.92MM
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
68 Pin Breakout Interface
VSI-Breakout-68
The VSI-Breakout-68 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
product
VME Test Extender 9U/400mm J1/J2/J0
111EXT9140-0120
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
cRIO-9041, 1.30 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 4-Slot CompactRIO Controller
786369-01
1.30 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 4-Slot CompactRIO Controller - The cRIO-9041 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 70T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
