Serial Data
-
Product
PXI Single 10 Channel MUX, XLR Connectors
40-735-902-S2
Multiplexer Module
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
Customizable EFP/ENG Signal Transport
BullDog Mini Series
-
An Ideal Solution For Small Remote Broadcast Productions The BullDog Mini is a compact, rugged field fiber transport device designed from the ground up to meet the needs of single camera and booth kit setups. The BullDog Mini can transport bidirectional 3G-SDI, IFB, and two MIC/line audios as well as, two serial data channels – all over a single strand of single-mode fiber. Optical connector options include SMPTE, opticalCon, or standard ST. With options for remote power via SMPTE hybrid fiber cable and battery operation, the BullDog Mini is ready for any location regardless of available power.
-
Product
PAM analysis upgrade for Signal Integrity Studio, WavePulser 40iX High-Speed Interconnect Analyzer
WAVEPULSER-SI-STUDIO-UPG-PAM
Analyzer
Signal Integrity (SI) Studio uses SDA Expert (SDAX) serial data analysis software options to simplify NRZ or PAM serial data jitter, eye diagram, noise and crosstalk measurement and analysis setup.
-
Product
ULI-211CI -Triple Isolated RS-232/422/485 (Terminal Block) To Multi-Mode Fiber Converter (ST Connectors) DIN Rail Mounted
BB-FOSTCDRI
-
Converts serial data signals to multi-mode ST fiber optic2 KV 3-way optical isolation (input/output/power); EMI/RFI protectionData rate: up to 115.2 kbpsWide operating temperature: -40 to +80 °CDIN mount, IP20 plastic case10–48 VDC power source required (not included, sold separately)UL Class 1 / Division 2
-
Product
Channeling Decoder, Nav/Comm/Control Head
RCD200
-
Designed to provide the Avionics shop a simple and expeditious method for testing general aviation radio tuning. Provided are front panel mounted LED's as well as a digital display to provide the quickest code recognition while testing. With this simple method of testing you will soon find yourself testing all your radios and finding those troublesome intermittents. This unit also decodes altitude and ARC 1000 serial data. Click on picture for larger view.
-
Product
4 Channels, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTF
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
Dual Channel Bit Synchronizer for Rates up to 45 Mbps
LS-45-DB
-
The Lumistar LS-45-DB Dual Channel Bit Synchronizer Daughterboard provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digitaldesign assures a high performance, consistent product, with excellent reliability and long-term stability. Dual channel design can feed each channel of the LS-55-DD dual decom. The LS-45-DB also has a post D combiner that allows for optimal ratiocombining of the two input signals A unique Built-in-Test feature allows performance verification for the Bit Synchronizer to ensure the highest level of operation. Auto-test BIT is performed for a short duration on the application of power and tests more than 90% of the Bit Synchronizer components. This test verifies that power is properly applied, verifies that there are no internal bit errors, and performs other tests to ensure that the bit synchronizer is fully operational with status indication of results. Command-test BIT performs the same functions and can be initiated by the user at any time through the Lumistar software when used on Lumistar PC products. The user has the ability to generate internal pseudo-random patterns and calculate internal bit error rates with or without the injection of forced errors.Various status indicators are also available through the software. The Bit Synchronizer also contains a BER reader as well as frame sync pattern indicator.
-
Product
Modular Recording System
Xilinx Aurora
-
As a Xilinx® Alliance Program Member, Conduant is pleased to announce Xilinx® Aurora serial data transfer protocol compatibility with our flagship StreamStor® Modular Recording System.
-
Product
30 GHz Differential Probe with 2.92mm Interface
DH30-2.92MM
Differential Probe
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
PXI Dual 18 Channel MUX, 96-Pin SCSI Connector
40-735-912-S1
Multiplexer Module
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
Oscilloscopes
Oscilloscope
Our oscilloscopes offer a powerful combination of large and informative displays combined with advanced waveshape analysis capabilities - typically tailored to enhance the productivity of engineers in specific applications areas such as serial data test, disk drive test and automotive bus analysis.
-
Product
ULI-213E - Heavy Industrial RS-232/422/485 (Terminal Block) To Single Mode Fiber (SC Connector) Panel Mount Metal Chassis
BB-FOSTCDRI-PH-SC
-
Converts serial data signals to multi- or single-mode fiber, SC connector2 KV, 3-way isolation (input, output, power circuits)Data rate: 9.6 to 115.2 kbps (bit-wise enable)-40 to +85°C wide operating temperatureIP30 metal panel mount case (DIN rail adaptable)FCC, CE, IEC-61850-3, IEEE 1613, UL C1/D210-48 VDC power source required (not included, sold separately)Note: 2 units required to extend data via fiber optic connection (see datasheet)
-
Product
Data Communications
-
Renesas' MIL-STD-883-compliant CMOS Manchester Encoder-Decoder (MED) is a high-speed, low power device manufactured using self-aligned silicon gate technology. The device is intended for use in serial data communication, and can be operated in either of two modes, a converter mode or repeater mode. This device is qualified to QML Class Q military standards.
-
Product
ULI-211E - Heavy Industrial RS-232/422/485 (Terminal Block) To Multimode Fiber (ST Connector). Panel Mount Metal Chassis
BB-FOSTCDRI-PH-MT
Terminal Block
Converts serial data signals to multi- or single-mode fiber2 KV, 3-way isolation (input, output, power circuits)Data rate: 9.6 to 115.2 kbps (bit-wise enable)-40 to +85°C wide operating temperatureIP30 metal panel mount case (DIN rail adaptable)FCC, CE, IEC-61850-3, IEEE 1613, UL C1/D2Note: 2 units required to extend data via fiber optic connection (see datasheet)10-48 VDC power source required (not included, sold separately)
-
Product
PCI Bit Synchronizer
LS-40-P
-
The Lumistar LS-40-P PCI Bit Synchronizer provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digital design assures a consistent product with high reliability and long-term stability. The LS-40-P PCI Bit Synchronizer consists of the LS-40-DB Bit Synchronizer Daughterboard shown below mounted on a PCI carrier board.
-
Product
PMC Compatible Bi-Directional Serial Data Interface
PMC-BiSerial III
-
The PMC BiSerial family has been updated to include a Spartan III [Xilinx] based card with expanded capabilities.. Building on the knowledge and experience gathered from multiple IP and PMC BiSerial implementations and adding in the latest technology has created the PMC-BiSerial-III. The BiSerial III features completely isolated FIFOs with 32 bit ports for increased adaptability and performance.
-
Product
Compatible Bi-Directional Serial Data Interface
PMC-BiSerial-IO-II
-
The PMC BiSerial has been updated to be even better. Building on the knowledge and experience gathered from multiple IP and PMC BiSerial implementations and adding in the latest technology has created the PMC-BiSerial-II. The BiSerial II features completely isolated FIFOs with 32 bit ports for increased adaptability and performance.
-
Product
3U Processor Board
CP39104
-
LinkedHope Intelligent Technologies Co.,Ltd.
Designed for industrial communication, CP39104 is a 3U CPCI serial card compliant with PICMG 2.0 R3.0 specification.CP39104 applies XR17D154 serial communication controller of EXER, and supports 4x RS232/RS422/ RS485. Therefore, CP39104 is highly suitable for testing and measuring in serial data communication applications.LinkedHope® provides CP39104 with a wealth of software drivers and BSP, including VxWorks, Linux, Windows, etc., to enable a wide range of application scenarios.
-
Product
DH Series High-Temperature Solder-In Tip, 16 GHz BW, 3.5 Vpp Range
DH-HITEMP
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
PMC Compatible Bi-Directional Serial Data Interface
PMC-BiSerial II
-
The PMC BiSerial has been updated to be even better. Building on the knowledge and experience gathered from multiple IP and PMC BiSerial implementations and adding in the latest technology has created the PMC-BiSerial-II. The BiSerial II features completely isolated FIFOs with 32 bit ports for increased adaptability and performance.
-
Product
PCI Express® 5.0 Interposer
OCP NIC 3.0
Interposer
The Summit product family includes a wide variety of Interposer systems, designed to reliably capture serial data traffic while minimizing perturbations in the serial data stream. Probes include interposers, which are designed to capture data traffic crossing the PCI Express card connector interface, and MidBus probes, which are designed to capture traffic flowing within a PCB.
-
Product
Serial Converter, RS-232/422/485 TB To MM Fiber ST (Inverted), Ind. DIN, C1D2
BB-FOSTCDRI-INV
-
Converts serial data signals to multi-mode ST fiber opticInverted fiber state - fiber light OFF in idle state2 KV 3-way optical isolation (input/output/power); EMI/RFI protectionData rate: up to 115.2 kbpsWide operating temperature: -40 to +80 °CDIN mount, IP20 plastic case10–48 VDC power source required (not included, sold separately)UL Class 1 / Division 2 rated
-
Product
DH Series Solder-In Tip, 30 GHz BW, 3.5 Vpp Range
DH-SI
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Bit Synchronizer Daughterboard Rates up to 25 Mbps
LS-40-DB
-
The Lumistar LS-40-DB Bit Synchronizer Daughterboard provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digital design assures a high performance, consistent product, with excellent reliability and long-term stability.
-
Product
DH Series Tip - CrossSync PHY PCIe5 CEM x16
DH-CSPHY-PCIE5-CEMX16
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
4 Channels, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTC
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
Quad Serial FPDP Interface with Virtex-6 FPGA - PCIe
Model 7811
-
Model 7811 is a member of the Cobalt® family of high performance XMC modules based on the Xilinx Virtex-6 FPGA. A multichannel, gigabit serial interface, it is idealfor interfacing to Serial FPDP data converter boards or as a chassis-to-chassis data link. The 7811 is fully compatible with the VITA 17.1 Serial FPDP specification. Its built-in data transfer features make it a complete turnkey solution. For users who require application-specific functions, the 7811 serves as a flexible platform for developing and deploying custom FPGA processing IP.
-
Product
Load Cell Transmitter
MODEL SST-LV
-
The SST-LV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-LV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-LV may be powered from 12-30 Vac or 10-48 Vdc. The SST-HV Has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
WaveMaster Oscilloscope, 13 GHz Bandwidth, 4 Input Channels, 40 GS/s Max Sample Rate
WaveMaster 813Zi-B
Oscilloscope
Up to 20 GHz bandwidth and 80 GS/s sample rate.The most advanced oscilloscope user interface.The industry’s only true hardware 14.1 Gb/s serial trigger.Low Jitter Measurement Floor and exceptional timebase stability.Comprehensive set of serial data analysis, debug, validation and compliance tools.Integrated 50 Ω and 1 MΩ inputs for true connection and probing flexibility.Integrated standard and custom measurements and math functions for unrivaled analysis capability.Multi-lane serial data eye, jitter and crosstalk analysis.Real-time de-embedding, emulation, and equalization.
-
Product
Data Analyzer, 16 GHz Bandwidth, 4 Input Channels, 80 GS/s Max Sample Rate
SDA 816Zi-B
Analyzer
16 GHz, 80 GS/s, 128 Mpts/Ch Serial Data Analyzer with 15.3" WXGA Color Display. 50 ohm and 1 Mohm Input, 6.5 Gb/s Serial Trigger, 8b/10b and 64b/66b decode. Also operates in 4ch, 40 GS/s, 64 Mpts/Ch mode.
