Drive-in Chambers
-
Product
Thermally Protected Ballast Heating Test Chamber
TPB-UL935
-
Working room dimension: 610×610×610mm• Temperature range: RT+10℃～+100℃• Materials of inner and outside chamber: Senior stainless steel• Insulation Material: Ultra-fine glass wool insulation material• Heater: Dedicated strip heater (heating surface area of 300 × 40 mm), each group three hundred watts, a total of four groups, with the power supply in parallel.• Special wooden test sample holder• Third gear temperature measurement points (at any time monitoring and conversion)
-
Product
Walk in Chamber for Rapid Rate Temperature / Humidity Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL Walk in Chamber for Rapid Rate Temperature / Humidity Test Relevant standards requirement:Temperature shockTest Object: Battery storage pack or system.Li-ion battery pack or system placed in (-40±2)℃~(85±2)℃ alternation temperature, the conversion time of two extreme temperatures is less than 30 minutes. Place the test objects into each extreme temperature keep 8h, test 5 cycles.Observe for 2 hours under the room temperature after testing,Humidity & Temperature CyclingTest Object: Battery storage pack or system.Refer the GB/T2423.4 Test Db, variable refer the Graph 4,the highest temperature is +80℃,5 cycles. Observe for 2h under the room temperature.
-
Product
Walk-In Solar Panel Test Chamber
-
For testing various size Walk in Solar Panel Test Chamber WIEBER designs and manufactures Walk in Solar Photovoltaic Testing Chamber. The test are to be performed according to various standards of ASTM, IEC, UC etc. Solar panels need to pass environmental tests as per IEC and other standards requirements to prove their long term performance and resistance to temperature and humidity extremes.
-
Product
Walk-In Environmental Test Chambers
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL’s Walk-in Environmental Test Chambers are available in large capacity test requirement, especially the EV battery, storage system and solar panel. We are able to provide various walk-in chamber specifications and customized design chamber to meet various special specimen size and test requirement. As an environmental test chamber manufacturer, we also provide walk-in environmental chambers for sale, all the walk-in environmental chamber cost is at factory price.
-
Product
Environmental/Stability Chambers
-
Canden offers unique- Dual environment chamber-This model allows users to set different temperature, humidity setting in 2 sections with in the same chamber divided by a common wall.
-
Product
Thermal Shock Test Chamber (2 Zone)
-
Guangdong Test EQ Equipment co., Ltd.
- Thermal Shock Chamber: -70℃~150℃, ≤5min recovery, meets MIL-STD-810. Ideal for PCB/IC reliability testing.- ESS Environmental Chamber: Humidity 20%~98% RH, supports GB/T 2423 standards. 40% energy saving vs. competitors.- Liquid-to-Liquid Shock Tester: LN₂ cooling to -196℃, 15s transition time. For aerospace materials validation.- Thermal Cycling Equipment: 25℃/min ramp rate, 1000L capacity. JESD22-A104 compliant.- Benchtop Thermal Chamber: -65℃~150℃, 65dB low noise. Lab-use with USB data export.
-
Product
Dust Test Chamber
-
Xi'an LIB Environmental Simulation Industry
Used to test the durability and sealing integrity of products (electronics, automotive parts, materials) against harsh, dusty conditions.
-
Product
Reach-In Solar Panel Test Chamber
-
For testing various size solar panels WIEBER designs and manufactures Solar Panel Test Chamber. The test are to be performed according to various standards of ASTM, IEC, UC etc. Solar panels need to pass environmental tests as per IEC and other standards requirements to prove their long term performance and resistance to temperature and humidity extremes. Solor Chamber also known as Solar Photovoltaic Testing Chamber and PV Module Test Chamber.
-
Product
Consumer Battery Test Chambers
-
Guangdong Bell Experiment Equipment Co.,Ltd
Many electronic products are around our daily life nowadays, smartphones, tablet, wearable devices, laptops, home robots, etc. The rechargeable battery, mainly Lithium-ion battery are widely adopted in such products. There is a greater demand for battery safety testing from both battery and product manufacturers. They should make sure the battery is qualified before delivering it to customers. As a lithium battery test chamber supplier, DGBELL dedicated to the R & D of battery safety tests in China with many technical patents. In this 10 years experiment of researching and manufacturing, we keep developing new equipment and improving the battery test system from cooperating with thousands of customers. DGBELL dedicates to provide a reliable and comprehensive solution for lithium battery test chambers, matching the standard IEC 62133, UN 38.3, and UL 1642. Including mechanical, electrical and temperature environmental test chambers.
-
Product
Drug Stability Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
If you want find complete details about Integrated drug stability test chamber, Drug stability test chamber, Chemical drug stability test chamber, New designed integrated drug chamber, Good quality integrated drug test chamber - China Sanwood Environmental Chambers Co., Ltd. The scientific method to create a drug for a long time to failure evaluation of stable temperature, humidity and light environment for pharmaceutical enterprises to accelerate drug test, long-term test, high humidity and strong light test, is the best choice for pharmaceutical companies and drug stability test program.
-
Product
Thermal Shock Test Chambers
-
How well does your product stand up to the shock of extreme thermal temperature changes? Tenney Environmental's thermal shock test chambers take products from 200°C to -65°C in just seconds.
-
Product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
Test Fixture
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
Product
Archival Storage Chambers
AR Series
-
The Darwin Chambers AR series is designed specifically for the needs of archival preservation. This series is capable of providing long-term controlled storage of photographs, film, rare books, papers, and paintings. Utilizing a simple. precisely controlled refrigeration system and advanced desiccant-based dehumidification, temperatures are maintained to within ±0.2ºC (at the sensor) and relative humidity to within ±1% (at the sensor).
-
Product
Environmental Test Chambers
-
An enclosure used to test the effects of specified environmental conditions on biological items, industrial products, materials, and electronic devices and components.
-
Product
Benchtop Test Chambers
MicroClimate
-
The MicroClimate 1.2 cubic foot benchtop test chamber is capable of simulating a full range of temperature and humidity conditions. This environmental testing chamber is designed to provide users with a compact unit for testing small components and products.
-
Product
Ultra-Cold Chambers
MC Series
-
Despite its compact size, the MC series can achieve low temperatures of -75 or -85°C the lowest range of its class. On the high end 100 or 180°C can be reached, depending on the specific model.
-
Product
Steam Aging Test Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Steam aging test chamber is a climatic test machine used to judge the products performance to resist extreme circumstance under high temperature, high humidity and high pressure during the transportation, storage and usage. The principle is very simple, water in the tank is heated turning into steam to form a simulated test environment under specified temperature and humidity. Specimens are placed into the drawers of machine to carry out test lasting for preselected time. It is applicable to electronic connectors, semiconductor IC, transistor, LCD, diodes, resistances etc.
-
Product
HMV Horizontal Flame Chamber - Motor Vehicles
-
Atlas Material Testing Solutions
Atlas’ HMV chamber determines the comparative burn rates and burn resistance of textiles, plastics and other automotive interior materials.
-
Product
Non-Nitrogen HALT Chamber
-
An advanced environmental test system that performs Highly Accelerated Life Testing (HALT) without relying on costly liquid nitrogen (LN2) for rapid cooling.
-
Product
Environmental Test Chambers
-
Dongguan Kejian Instrument Co., Ltd.
UV accelerated weathering test chamber simulates damaging effects of long term outdoor exposure of sunlight, heat, moisture on materials and coatings. It exposes specimen to varying conditions of weathering- ultraviolet radiation, moisture and heat to test the performance and improve the quality.
-
Product
Solar Spectrum Test Chamber / Solar Radiation Test Chamber
-
WEIBER Solar Spectrum Test Chambers are one of solutions to be utilized in large scale PV testing program. We offer customized as well as standard multidimensional test program for PV modules in reasonable prices. This system delivers the weathering stress representative of long term outdoor exposure.Our flexible system can be designed according to our test requirements, to suit environmental test conditions like volume, temperature, humidity solar radiation intensity and other measuring instruments. Weiber provide Solar Radiation Test Chamber.WEIBER solar test system are recognized for superior solar simulation environmental Testing, evaluating outdoor use product reliability, quality & safety. This technology allows for very high concentrations of UV energy without excessive heating of test samples. Custom mounting and cooling can be added depending upon specific material exposure requirements. MHGs (metal halide global lamps) are used as radiation source. Weiber provide Solar Simulation Test Chamber.
-
Product
Environmental Chamber
REXMED REC-200
-
MOD. REC-200, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -20˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -20˚C~100˚C within 35 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 1,892 Watts, 6,455 BTU/hr, 1,630 Kcal/hr, Cool down transition time: 20˚C~-20˚C within 45 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L50 X W60 X H75cm, Capacity: 225L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
Walk-in Modular Chambers
FL-M
-
Prefabricated chambers, rooms, and drive-in facilities, made from sectional panels, can be constructed in any size ranging from the very small to the extremely large. They are often a first choice when there is restricted access to the final assembly location or when initial cost is an important consideration. We manufacture a complete line of both prefabricated modular chambers, assembled from sectional panels on site, and welded integral chambers.
-
Product
Reach-In Conditioning Test Chamber
-
Weiber Conditioning Test Chamber Manufacturers offers an ideal apparatus for conditioning materials at non-ambient temperatures. Now researchers, engineers, and technicians have a simple and cost effective method to condition samples prior to testing. Laboratory Conditioning Chamber is designed for the conditioning of samples prior to testing, provides conditions from 20% to 98% RH ± 2 and 0°C to 94°C ± 0.5°C.Conditioning Test Chambers offers ideal humidity and temperature conditions required for testing the effect of environmental changes on the product. The chamber can be widely used to evaluate the durability of various products. Weiber delivers customized products at the most economical rate and within the limited delivery period.
-
Product
Platinum Chambers
-
The Platinum series are top quality temperature/humidity chambers in four larger sizes than our popular Platinous and Global-N lines. More powerful heating and cooling systems on these models ensure prompt response, even with larger and heavier loads. Change rates up to 12°C/m or more is possible, depending on the model.
-
Product
Test Chambers
Anechoic
-
Free Field Test Chamber for sound pressure level measurement, sound power level determination, acoustic research and audio measurement applications
-
Product
Althletic Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
The Athletic Environmental Chamber is specifically design for athletic training which request the CO2 , O2 control inside the environmental chamber. It is suitable for sports and science investigation.
-
Product
Precision Altitude & Climate Test Chamber
-
Guangdong Test EQ Equipment co., Ltd.
Primarily used in aviation, aerospace, shipbuilding, military equipment, electrical engineering, electronics, automotive, motorcycle, telecommunications, and scientific research industries to evaluate the reliability of electrical/electronic products, instruments, and other equipment during transportation, storage, and operation.
-
Product
Low Outgassing Cables Suitable For Thermal Vacuum Chamber Exposure
-
Low Outgassing Cables Suitable for Thermal Vacuum Chamber Exposure.
-
Product
Hydrostatic Test Chambers
-
Test chambers are available to protect personnel during proof or burst testing. A few samples are pictured below. Chambers are manufactured in polished stainless steel with a clear polycarbonate door(s) for visibility during testing. Fluid port(s) are provided inside the enclosure, while all controls remain outside the enclosure for operator safety. In a hurry? Choose from our selection of Quick Ship Test Systems. basic units can ship within 24 hours or less and chamber systems within 2-3 days. we normally stock test chambers with nominal working area dimensions of either 24" wide x 24" deep x 15" high, 36" x 36" x 15", 48" x 24" x 15" or 72" x 24" x 12" with the door opening from the top. specify individual parameters at our customization page. Need a different size or configuration? No problem, simply specify dimensions and features that more accurately meet your particular requirements and we will be pleased to accommodate you. To customize a system to fit your particular application, please visit our customization page or give us a call at (916) 645-3317.
