-
product
Probes And Cables
The iProbe is an intelligent temperature sensor that can be calibrated independently of SBIR’s blackbody systems or 104i precision thermometers. These ultra-stable, highly responsive iProbes are used to provide long term accuracy and repeatability of under 0.010°C. Each iProbe incorporates onboard flash memory that allows all calibration constants and calibration date information to be stored independently of the blackbody or thermometer system. This allows iProbes to be exchanged for use on a blackbody or thermometer without any loss in stability or accuracy. To re-calibrate a system you need only exchange the current iProbe with a recently calibrated one. No special equipment is required and there is no down time in the test area.
-
product
Directional Hotwire Probe
AP471S3
Directional hotwire probe, 180°C articulated tip for easy positioning, to measure air speed in the range 0.1…40 m/s and air temperature in the range -25°C…+80°C.
-
product
Coax, Contact, ITA, 75 Ohm, RG179
610103169
Primary mating contact 610104157. (May mate with other Receiver contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – brassCenter Contact – BeCuContact Plating Center Conductor Shield - 30µ” Au over 100µ” NiContact Termination Center Conductor – Crimp or SolderShield – CrimpInsulator PTFEMating Force 4.0 lbs max [1.81 kg]Electrical SpecificationsCharacteristic Impedance 75ΩFrequency Range DC to 3 GHzVSWR < 2.95 @ 3 GHzInsertion Loss -1.64 @ 3 GHzDWV 800 VRMSContact Resistance Center Contact is 5 milliohms Outer Contact is 3 milliohmsCable Specifications RG179Environmental SpecificationsOperating Temperature -55°C to +125°CVibration MIL-STD 1344, Method 2005, Test Condition 4Shock MIL-STD 1344, Method 2004, Test Condition AInsulation Resistance 1000 MΩ min.
-
product
Microprobe Thermometer-Rechargeable
BAT-12R
The BAT-12R rechargeable laboratory digital thermometer is Physitemp's most popular and best selling instrument due to its versatility, quality construction and low cost. The BAT-12R has 0.1°C resolution and super accuracy of 0.1°C ±1 digit between 0-50°C, 0.1°C ± 1 digit over full range.The temperature range is -100 to 200°C. The BAT-12 provides fast readings, usually within 2-5 seconds depending on the temperature probe in use.
-
product
High Current Probe/DMM
655
Another great tool for all around electrical troubleshooting. The #655 is ideal for all high current applications, especially starting and charging diagnostics. The #655 can measure up to 1000 Amps AC or DC. Unit features built-in degrees F and C temperature readings.
-
product
RTOS Scheduling Visualization
RapiTask
*Examine Ada, C or C++ applications via scheduling visualization*Locate rare timing events that need attention*Identify bottlenecks in your application by analyzing capacity issues*Compare scheduling algorithms from different RTOSs
-
product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Ferrules, 1m HV, Exit Away From Pin 1
40-972-050-1m-MU-HV
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Gauge Type T Thermocouple Wire
W-TW-30
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
product
Cameras
Miro C and N
The Phantom Miro C and N series cameras are designed to fit into spaces that a standard camera can't reach. Lightweight bodies, on-board data protection, and rugged construction make them popular in automotive, microscopy, and destructive testing environments.
-
product
C/Ku Band Satellite Monitoring
SCL-3412
C/Ku Satellite Monitoring System (SCL-3412) is designed to intercept International/national telecom carriers, GSM A/Abis links and IP Carriers over satellite which are using C, Ku, X or Ka-Band. In order to reduce the manual effort and time consumed in the analysis of the carriers, system is integrated with Satellite Carrier Analysis module, which automatically performs the scanning on the selected spectrum and provide the list of carriers along with their payload type (i.e DCME, GSM or IP) and characteristics parameters. This provides great help to take decision for monitoring of the carriers of interest.
-
product
Hand held, Battery-Powered Voltage Source
DVC-350A
Hand held, lightweight 11 ounce (342 grams)Laboratory accuracy of 0.015% of FSR at +25 C, traceable to the National Bureau of Standards4 1/2 Digit LCD display100 V incrementsTwo output voltage rangeDecimal: 1.2V dc, 12V dcHexadecimal: 1V dc, 10V dc
-
product
CX4000 – FTIR Gas Analyzer
Gasmet CX4000 is an industrial multi-component FTIR gas analyzer for continuous emission monitoring applications, integrated into a Continuous Emissions Monitoring system (CEMS II e). It can be used to measure up to 50 components simultaneously, and additional gases can be easily added without any hardware changes. The corrosion-resistant sample cell is heated up to 180 °C, which makes CX4000 an ideal tool for analyzing trace concentrations of pollutants in wet, corrosive gas mixtures.
-
product
PXIe-4082, 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, L and C Measurement Support, PXI Digital Multimeter
783131-01
PXIe, 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, L and C Measurement Support, PXI Digital Multimeter—The PXIe‑4082 is a high-performance 6½‑digit, 300 V DMM that provides the measurement capabilities found in two common test instruments: a high-resolution DMM and a digitizer. As a DMM, the PXIe‑4082 delivers fast, accurate AC/DC voltage, AC/DC current, 2‑ or 4‑wire resistance, frequency, period, and basic L and C measurements, as well as diode tests. In the high-voltage, isolated digitizer mode, the PXIe‑4082 can acquire waveforms at sample rates up to 1.8 MS/s.
-
product
Robust RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, 1 COM, 1 LAN, DIO (4-in/4-out) And Optional CANbus
Agent200-FL-DC
*RISC-based (i.MX 6UltraLite) processor 528 MHz*256MB DDR3 SDRAM onboard*4GB eMMC flash onboard*2 PCI Express Mini Card slots (Wi-Fi or 3G/4G)*4 digital inputs and 4 digital outputs*Power input range of 9V to 48V DC with terminal block*Embedded Linux (Yocto) operating system*Fanless and compact design*Wide operating temperature range from -40°C to +70°C
-
product
ARINC 429 Test & Simulation Interface for PCI
PCI-C429
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/FilteringIRIG-B time code encoder/decoder with free-wheeling modeApplication Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Tinned Ends, 2m, HV
A037DF4-T-HA200
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
pH 5+ Handheld pH Meters
These meters are perfect for fast, accurate results. Automatic temperature compensation (ATC) ensures accuracy from 0 to 80°C. Meters include a protective rubber boot that also acts as a meter stand.
-
product
DC/DC Converter 50 W
CTS-60-6839
DC/DC converter with 50 W from Premium | input ranges 28.8 - 60 VDC | output 5 V | operates in temperatures from -25 - +85 °C | designed according to EN50155
-
product
150W to 240W - Single Output
ZWS-BP Series
*200% Peak Power Capability*Operating temp. -10°C to 70°C*10 Year e-cap Lifetime*Five year warranty
-
product
VME J2 12 slot
101VMEJ212-0900
VME J2 backplane 12 slot, compliant with ANSI/VITA 1-1994. The A+C rows are bussed in all slots. Also, row B has onboard, inboard termination.
-
product
CompactPCI 3U Module
CPCI-1553-DDC
Operating temperatureCommercial: 0 to +55 °COptional: -25°C to +80°C• Non-operating: -40°C to 85 °C• Airflow requirement: .5 CFM• Humidity: 5 to 90% (non-cond.)• Altitude: 0 to 10’000 ft
-
product
Constant Temperature Humidity Battery Test Chamber
Guangdong Test EQ Equipment co., Ltd.
- Battery-Specific Thermal Management: Dual-compressor cascade cooling (-40°C stability) and ceramic heaters for rapid high-temperature recovery.- Precision Electrochemical Control: Integrated battery cyclers with CAN/Modbus protocols, supporting SOP (State of Power), SOH (State of Health), and DCR (Direct Current Resistance) monitoring.- Safety-Centric Design-meet Hazard Level: Chambers are designed with Fire-resistant stainless steel interior, fire suppression,nitrogen purge system, and emergency power cutoff for thermal runaway prevention .- Data Acquisition & AI Analytics: Real-time logging of voltage, current, temperature, and pressure via LabVIEW/Python APIs. AI-driven anomaly detection reduces test cycles by 30%.- Energy Efficiency and Energy Storage: Heat recovery during discharge cycles cuts energy use by 25% (ISO 50001 compliant).
-
product
NI-9209, ±10 V, 500 S/s, 16-Channel C Series Voltage Input Module
783729-01
±10 V, 500 S/s, 16-Channel C Series Voltage Input Module - The NI‑9209 performs single-ended or differential analog input. This module provides 60 VDC CAT I isolation and built-in 50/60 Hz filtering, making it a valuable addition to industrial measurement systems.
-
product
Vertical Thermal Shock Chambers
FSV Series
Bemco FSV Series Vertical Thermal Shock chambers are available in two zone (FS2V - hot and cold) and three zone (FS3V hot - cold - hot) versions, with two temperature ranges (-75 C to +200 C or -160 C to +200 C), and two types of cooling systems (all mechanical cooling - no expendable refrigerant required, or all LN2). Very low temperature, -160 C chambers, are always liquid nitrogen cooled. Two zone chambers are offered in four standard sizes, while three zone chambers are offered in three standard sizes.
-
product
RTD Measurement for CompactPCI
CPCI390
The CPCI390 has a 3U form factor and features six 2-, 3-, or 4-wire high-accuracy RTD measurement channels. Each channel has programmable alarm limits on which an interrupt can be issued. The local DSP (TMS320C203) performs linearization, auto-calibration and alarm limit checking. Sensordata is available in °C, °F, K and Ohm. All inputs are optically isolated from the system.
-
product
Anti-Freeze Tester
AFT-2
For testing methanol and ethylene glycol. With green and white scales. Green scale should be used when the engine is hot and white scale should be used when the engine is cold. Testing range: - Methanol - 40°C - 12°C, Ethylene Glycol - 34°C - 12°C. Manufactured with a glass tube, PVC bulb and spout
-
product
DC/DC Converter 2 W
R2SX-053.3/H
DC/DC converter with 2 W from Recom | input ranges 4.5 - 5.5 VDC | output 3.3 V | operates in ambient temperature from -40 to +100 °C | high isolation version
-
product
C Series Temperature Input Module
The C Series Temperature Input Module features up to 16 channels of temperature input from either thermocouples or RTDS. This module can include anti-aliasing filters, open-thermocouple detection, and cold-junction compensation. Additionally, the module also feature isolation for safety, noise immunity, and high common-mode voltage range.The C Series Temperature Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
Portable Power Source - Power Transformer and Charger Manufacturer
JYUE LII INTERNATIONAL CO., LTD.
A&V power transformer supplies and manufactures certified portable power source and charger with industrial UL / cULus / CB / CE / TUV & ISO 9001:14001 certified electrical products and manufacturing facilities based in Taiwan. Portable Power Source Includes C Series, H Series, J Series, L Series, M Series, P Series, Q Series, W Series, Power Bank Series Portable Power Source
-
product
Block Up-Converter
BUC Series 5” x 2.5” x 0.6”
*Connectorized Package *Compact, Rugged Design *C, X, Ku, K, and Ka-Bands Available *L-Band Inputs (950-2150 MHz) *Internal or External Filters Available *Variable Attenuation Control via CAN +5V Logic, SPI, RS232, or I²C
