Digital Visual Interface
See Also: DVI
-
Product
Multi-Channel, 10-Bit Digitizer
ADQ8-4X
Digitizer
ADQ8-4X offers software-configurable sampling on two or four channels. The sampling rate is 4 GSPS in two-channel mode or 2 GSPS in four-channel mode. This feature enables flexible operation during development since the channel count and sampling rate can be varied.The signal inputs are DC-coupled and offer programmable DC-offset as well as configurable input voltage range. It also supports high analog input bandwidth and therefore supports a wide range of sensors.
-
Product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 125 MS/ on 2 DAQ Channels and 2 AWG Channels
DN2.816-02
Digitizer
The hybridNETBOX DN2.80/81x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 16 bit resolution and is available with sampling rates of 40 MS/s and 125 MS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
NI-9475, 60 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module
780132-01
Digital Module
60 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module - The NI‑9475 works with a variety of industrial devices such as solenoids, motors, actuators, relays, and lamps. Each channel sources up to 1 A at levels up to 60 VDC and features isolation from … channel‑to‑earth ground.
-
Product
PCI-6514, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Output, Bank-Isolated Digital I/O Device
778836-01
Digital I/O
The PCI-6514 is an industrial digital I/O interface, with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in … software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6514 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
NI-9425, 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module
779139-01
Digital Module
24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module - The NI‑9425 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels. The NI‑9425 offers isolation between the input and output banks from channel to earth ground. You cannot use the NI‑9425 in a CompactDAQ chassis to perform counter operations.
-
Product
LIN Interface Module
C Series LIN
LIN Interface
C Series LIN Interface Modules are bus interfaces for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LDF databases in integrated LIN databases. C Series LIN Interface Modules work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
NI-9477, 60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module
779517-01
Digital Module
60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module - The NI‑9477 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. Each channel is compatible with signals from 5 V to 60 V and … features isolation from channel‑to‑earth ground. You can wire the NI‑9477 channels in parallel to sink up to 20 A of current per module (1 A per channel maximum).
-
Product
4CH 16-Bit 80 MS/s PXI Express Digitizer
PXIe-9834
Digitizer
The ADLINK PXIe-9834 PXI Express digitizer provides high speed, high quality data acquisition with four input channels supporting up to 80MS/s sampling and 16-bit data resolution. This allows simultaneous recording of signals on all channels with no interchannel phase delay.The PXIe-9834 features external digital trigger input and triggers from the PXIe system timing slot and reference clock from the PXIe chassis, making it easy to achieve high simultaneous channel count recording of 8, 12, 16 and 20 channels. The PXIe-9834 is also equipped with 1GB of onboard memory for data buffering before transferring back to system memory. The PCI Express x4 Gen1 data bus is has enough bandwidth for direct streaming of ADC data back to system, if necessary.
-
Product
RazorMax Express 16 CompuScope 16-Bit, 1 GS/s, PXIe Gen3 Digitizer / Oscilloscope
Digitizer
The GaGe RazorMax Express CompuScope PXIe Gen3 x8 digitizer features unprecedented speed and resolution with either four or two 16-bit channels at 1 GS/s and 600 MHz bandwidth, and PXIe Gen3 data streaming rates up to 5.2 GB/s in a 3U Single Slot PXIe form factor.
-
Product
NI-9881, 1-Port C Series CANopen Interface Module
781673-02
Interface Module
The NI‑9881 is a high-speed CANopen interface for developing CANopen applications in LabVIEW software on CompactRIO hardware. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. It was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The NI‑9881 can transmit/receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. The NI‑9881 is compatible with only CompactRIO systems.
-
Product
Low Thermal Input Cable
34102A
Digital Cable
Use this 1.2-m shielded, 4-conductor connector only with the 34420A Micro Ohm Meter; terminated in copper spade lugs.
-
Product
Databus-to-Network Interfaces
OBB2
Interface
The OBB2 is highly configurable and includes built-in standard peripherals (Ethernet, serial, and USB), along with four internal Cores that can be populated with a variety of databus protocols and discrete I/O modules. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box.
-
Product
Ethernet/LXI digitizerNETBOX 14 Bit High Speed Digitizer - 500 MS/s on 12 Channels, 12 Single-Ended Inputs
DN6.445-12
Digitizer
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
NI-6583, 200 MHz, 32 Single-Ended and 16 LVDS Channels, Digital I/O Adapter Module for FlexRIO
781320-02
Digital I/O Adapter
200 MHz, 32 Single-Ended and 16 LVDS Channels, Digital I/O Adapter Module for FlexRIO—The NI-6583 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 32 single-ended and 16 low-voltage differential signaling (LVDS) digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6583 can sample digital waveforms at up to 200 MHz. It includes support for selectable single-ended voltages from 1.2 to 3.3 Volts with 10 bit resolution and common LVDS voltages.
-
Product
1-2 Independent, Dual Redundant 1553 Channels on Small Mezzanine
MEZ-E1553
Ethernet Interface
From our popular ENET product, the MEZ-E1553 is a small, rugged mezzanine product that can easily be integrated into your system design. Alta provides full reference schematics, design notes, STEP 3-D Files, and sample ESS test programs. Guaranteed 1553A/B/C compliant with AS4111 5.2 Protocol Test reports.
-
Product
Dual-port Isolated CAN Interface Cards
PCI-7841/cPCI-7841
CAN Interface
The PCI-7841/cPCI-7841 is a Controller Area Network (CAN) interface card. It supports a dual-port CAN's interface that can run independently or bridged at the same time. The built-in CAN controller of this card is Philips SJA1000, which provides bus arbitration and error detection with auto correction and re-transmission function.
-
Product
Handheld Digital Multimeter, 4.5 digit, up to 800 hours battery life
U1282A
Digital Multimeter
60,000 counts resolution on dual display0.025% basic DC voltage accuracy Longer battery life up to 800 hours Certified to IP 67 for dust and water protection Tested to withstand a 3-meter (10-ft) drop Programmable via USB (Download Programming Guide here)CAT III 1000 V/ CAT IV 600 V overvoltage protection Vsense for non-contact voltage detection Square wave output for generating pulse width modulation (PWM) signal Frequency counter Low pass filter
-
Product
PCI-6512, 64-Channel, ±30 VDC, Source Outputs, Bank-Isolated Digital I/O Device
778968-01
Digital I/O
The PCI-6512 is an industrial digital output interface, with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6512 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
PCIe 8 Bit High Speed Digitizer - 2.5 GS/s on 1 Channel, 1.5 GHz Bandwidth
M4I.2220-X8
Digitizer
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PXI-6529, 48-Channel, Sink/Source Inputs, Channel-Channel Isolated PXI Digital I/O Module
779949-01
Digital I/O
48-Channel, Sink/Source Inputs, Channel-Channel Isolated PXI Digital I/O Module—The PXI‑6529 is an industrial, parallel digital input interface. PXI‑6529 devices are ideal for a variety of applications from automotive design, industrial factory automation, and machine control to aerospace, laboratory research, and biomedical applications. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6529 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Ethernet to CAN Bus Gateway
YAV90090
Ethernet Interface
• High-performance Arm Cortex-M3 MCU with 512 Kbytes Flash, 120 MHz CPU, ART Accelerator, Ethernet P/N STM32F207IEH6• USB 2.0 connector for serial data transfer (reserved for factory use)• Connections for CAN, and power supply via 4-pole Weidmüller connector• Reboot and reset of the device to factory defaults with a reset button• Plastic casing for benchtop operation• LEDs for device status and power supply• Voltage supply from 8 to 30 V
-
Product
Multi-Channel 1553 Interface for PCI Express 4 Lane Systems
PCIE4L-1553
Interface Card
Alta Data Technologies’ PCIE4L-1553 interface module is a multi-channel (1-4), ½ size, 4 Lane PCI Express 1553 card supported by the latest software technologies. The PCI Express card is based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
Product
NI-9375 , 30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781030-01
Digital Module
30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The NI‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The NI‑9375 offers isolation between the input and output banks from channel‑to‑earth ground.
-
Product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5050
Digital I/O Module
The GX5050 is a high speed Dynamic Digital I/O card that provides a full set of features that is comparable to high speed I/O products found in large functional test systems. The card shares an identical architecture with the GC5050, but the GX5050 is a PXI card (6U) and the GC5050 is a PCI card. Both have the ability to operate independently of the host computer when in RUN mode.
-
Product
ARINC PC/104-Plus Interface Card
PC104P-A429
Interface Card
Alta Data Technologies’ PC104P-A429 interface module offer a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 physical layer signal.
-
Product
32-Ch Isolated Digital I/O And 1-Ch Counter PCI Card
PCI-1750
Digital I/O
16 isolated DI and 16 isolated DO channels.High voltage isolation on all isolated channels (2,500 VDC).High sink current on isolated output channels (200 mA/channel).Supports dry contact or 5 ~ 50 VDC isolated inputs.Interrupt handling capability.Timer/counter interrupt capability.
-
Product
16/32 GSa/s Digitizer
M8131A
Digitizer
Wideband 32GSa/s Optical Data Interface (ODI) modular stream-able digitizer.
-
Product
CompactPCI Interface Card
CPCIC-1553/PXI
Interface Card
The CPCIC-1553/PXI Interface Card and AltaAPI Represent the Latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology with Multi-Layer Software. Our Card and Software Packages are Designed for Fast, Portable Integrations. The CPCIC-1553 is the Only Commercial Off the Shelf (COTS) Card that Passes and Executes the SAE AS4111/4112 Protocol Tests.
-
Product
Digital I/O Board
3512
Digital I/O
The 3512 is an eight channel non-isolated digital I/O board with +5V tolerant 74LCX14 inputs with hysteresis and +3.3V CMOS 74LVTH125 driven outputs. Each I/O line features a series 10 ohm damping and protection resistor and a 4.7K pull up resistor to +3.3V. On power up the outputs are tri-stated, and can then be enabled on a bit by bit basis. Output high drive is 32mA @ 2.0V minimum. Output low drive is 32mA @ 0.8V maximum.
-
Product
PXI-8512, 2-Port, High-Speed, Flexible Data Rate PXI CAN Interface Module
780687-02
CAN Interface
2-Port, High-Speed, Flexible Data Rate PXI CAN Interface Module—The PXI‑8512 is a high-speed Controller Area Network (CAN) Flexible Data-rate (FD) interface for developing applications with the NI‑XNET driver. The PXI‑8512 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
