-
Product
PCIe-1433, Base-, Medium-, Full-Configuration Camera Link, PoCL Compatible Frame Grabber Device
781169-01
Frame Grabber
The PCIe‑1433 is a Camera Link image acquisition device designed for machine vision and scientific imaging applications that require high data throughput. The PCIe‑1433 includes an onboard … FIFO for higher bandwidth use cases, and it works with any base‑, medium‑, and full‑configuration Camera Link camera. The PCIe‑1433 is ideal for many industrial, life science, and biomedical imaging applications. The PCIe‑1433 also supports Power over Camera Link (PoCL) and can power cameras through PoCL‑enabled cables.
-
Product
FireBird Camera Link Frame Grabber (1xCLD-2PE4)
AS-FBD-1XCLD-2PE4
-
FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
Product
Virtex-5 XMC/PMC
XMC-FPGA05D
-
Curtiss-Wright Defense Solutions
The XMC-FPGA05D high density I/O module controlled by a user programmable Xilinx Virtex-5 FPGA and supported by a range of front panel I/O modules including analog I/O, RS-485/422, LVDS and Camera Link.
-
Product
Car Camera Bus (C2B)
-
Analog Devices Car Camera Bus (C2B™) is an innovative new camera link technology enabling HD video over Unshielded Twisted Pair (UTP) cables and unshielded connectors. C2B provides an easy upgrade path from SD to HD cameras without the need to change the existing cable and connector infrastructure. C2B enables a camera link with reduced system cost, significant weight savings and increased robustness. The C2B portfolio of transmitter and receiver devices enable seamless camera connectivity in the vehicle. The C2B technology was defined and designed for automotive applications and provides a robust camera link solution for these applications:
-
Product
Phoenix PCI/104e Camera Link Frame Grabber
AS-PHX-D48CL-104PE1
-
Phoenix-D48CL is a PCI/104-Express board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and line scan cameras. It supports all the formats of the Base and Medium configurations, i.e. single 8-to 16-bit data, through 12-bit RGB, to 4-tap 12-bit sources, as well as dual Base configuration, i.e. acquisition from two asynchronous Base cameras.
-
Product
IP Core and FPGA Products
-
Our FPGA offerings include development boards and IP cores for Altera FPGA devices. The IP cores include: I2C, PCIe, JPEG-LS, LVDS Camera Link and memory controllers.
-
Product
CL MX4 Frame Grabber
Xtium-CL MX4
-
Building on the field proven capability of Teledyne DALSA’s Xcelera frame grabber series, the Xtium™-CL MX4 is based on industry standard PCI Express™ Gen 2.0 expansion bus to deliver high speed access to host memory. The new Xtium series offers higher bandwidth to sustain Camera Link® 80-Bit modes over longer cable distances and supports a wide variety of area and line scan color/monochrome cameras, all in a compact, half-length, single slot solution.
-
Product
Digital I/O
-
Curtiss-Wright Defense Solutions
Curtiss-Wright Digitial I/O cards include interfaces to LVDS, Camera Link, Serial intrefaces, CANbus and customizable I/O. With over 20 years experience in the design and production of top quality COTS signal acquisition hardware, we deilver PMC, XMC and PC/104 modules that can cope with the toughest operating environments.
-
Product
FastCamera
FC1700
-
The FastCamera FC1700 is a high-speed 17 megapixel digital camera system, using a CMOS imager with an electronic global shutter, or rolling shutter. This camera has a high-speed, scalable, integrated FPGA, image processor, and memory subsystem which enables stand-alone high speed in camera image processing and extended storage. Options include ruggedized, Expanded Camera Link output, Gigabit Ethernet output, and in camera recording. When integrated with a high powered frame grabber /coprocessor board, the resulting system capabilities can be expanded by adding processors and memory on the board according to the needs of the user.
-
Product
Miniature 12G/3G/HD-SDI Fiber Transport
SilverBULLET Series
-
Sometimes you just need that “silver bullet” - a simple solution that solves problems. Maybe it’s a quick connection to support temporary video and audio feeds, or perhaps just a rock-solid fiber-optic connection for single-link transport to and from a camera. MultiDyne’s SilverBullet Series offers an economical solution for broadcast-quality signal transmission on single-mode fiber. At just three inches, the SilverBullet offers a compact, interlocking architecture to ensure robust links that can fit just about anywhere. SilverBullets come in a compact carrying case that includes the DC power supplies. Ideal for a wide variety of broadcast and professional AV applications including field production, remote camera links, courtesy feeds, cross-campus production and pre-fibered venues.
-
Product
Cable, Power over Camera Link (PoCL), MDR to SDR, 5M
199745-05
-
26-Pin MDR/SDR Camera Cable - The PoCL Cable provides a Power over Camera Link (PoCL) cable assembly. This cable carries power as well as signal communication for PoCL applications between compatible cameras and frame grabbers. The PoCL Cable is available in 26-Pin Mini Delta Ribbon (MDR) male to 26-Pin MDR male, or 26-Pin MDR male to 26-Pin Shrunk Delta Ribbon (SDR) male variations.
-
Product
FastCamera
FC300
-
The FastCamera 300 is a high-speed 3 megapixel digital camera system, using a CMOS imager with an electronic global shutter. This camera has a the option of a high-speed, scalable, integrated FPGA, image processor, and memory subsystem which enables stand-alone high speed in camera image processing and extended storage. Options include back thinned versions with high QE in the visible and NIR range, ruggedized, Camera Link output. When integrated with a high powered frame grabber /coprocessor board, the resulting system capabilities can be expanded by adding processors and memory on the board according to the needs of the user.
-
Product
Cable, Power over Camera Link(PoCL),MDR to MDR,2M
199744-02
-
26-Pin MDR/SDR Camera Cable - The PoCL Cable provides a Power over Camera Link (PoCL) cable assembly. This cable carries power as well as signal communication for PoCL applications between compatible cameras and frame grabbers. The PoCL Cable is available in 26-Pin Mini Delta Ribbon (MDR) male to 26-Pin MDR male, or 26-Pin MDR male to 26-Pin Shrunk Delta Ribbon (SDR) male variations.
-
Product
Xcelera Frame Grabber Family
-
The Xcelera Series leverages the PCI Express (PCIe) platform to bring traditional image acquisition and processing technology to new levels of performance and flexibility. This unified and scalable platform currently supports high-performance Camera Link™ cameras.
-
Product
Single Sensor - Monochrome Line Scan Cameras with Fast Scan Rates
-
JAI’s monochrome line scan cameras provide an excellent combination of high resolution and fast scan rates.The Sweep SW-8000M-PMCL model features an 8192-pixel linear CMOS sensor delivering a line rate of 100,000 lines/s (100 kHz) over a Camera Link interface. The SW-4000M-PMCL model is based on a 4096-pixels sensor capable of running as fast as 200,000 lines/s (200 kHz) over Camera Link.
-
Product
Camera Link
R3-CL
-
The R3 frame grabber family has been designed to simplify the task of interfacing today's Camera Link cameras to a wide array of imaging applications. The R3-CL can acquire from almost every Base CL camera manufactured.
-
Product
Industrial Cameras
-
High-performance CMOS cameras with GigE Vision, USB3 Vision and Camera Link.
-
Product
Digital I/O
-
Curtiss-Wright Defense Solutions
Our digital I/O cards include interfaces to LVDS, Camera Link, Serial interfaces, and customizable I/O. Built leveraging our decades of experience producing highly rugged COTS signal acquisition hardware, our PMC and XMC modules are designed to perform reliably in the toughest operating environments.
-
Product
Xtium Frame Grabber Family
-
The Xtium series delivers higher bandwidth to sustain Camera Link 80-Bit modes over longer cable distances and supports a wide variety of area and line scan color and monochrome cameras, all in a compact, single slot solution.
-
Product
Framegrabber
FastX-APU
-
The FastX-APU framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX-APU, is a two thirds length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as GigEx4, high speed analog formats such as UXGA or DVI, or CoaXPress. The front-end data is formatted and preprocessed by a Kintex FPGA before being sent to the PCIe (X4) Gen 2 switch to the host or the AMD APU.
-
Product
Framegrabber
FastX1703
-
The FastX1703 framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX1703, is a two thirds length raw form factor PCI board six basic 85 MHz Camera Link Channels or an extended Camera Link camera interface. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as LVDS or high speed analog formats such as UXGA or DVI. The front-end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, up to four PNX1702 500 MHz processors with 256MB memory each. Finally, the FastX1703 interfaces to the host computer through a 4xPCIe interface for state-of-the-art data acquisition.
-
Product
FireBird Camera Link 3U cPCI Serial Frame Grabber
AS-FBD-1XCLD-3CPCIS-2PE4
-
The FireBird Camera Link CompactPCI Serial card is a member of Active Silicon’s state-of-the-art FireBird frame grabber family. FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
Product
2-Port PCI Express Camera Link, Base Frame Grabber
PCIE-1122B-AE
Frame Grabber
Half-Size PCI Express Board Gen 2.0 x4Camera Link clock up to 85 MHzSupports 2 Base CL camerasSupports PoCL and non-PoCL cameras with SafePowerImage sizes up to 268,435,456 x 16,777,216Independent I/O (trigger, encoder, strobe, etc) for each camera
-
Product
FireBird Camera Link Frame Grabber (2xCLM-2PE8)
AS-FBD-2XCLM-2PE8
-
FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
Product
PXIe Digital I/O: 28 LVDS Channels, 8 Trigger Channels
M5302A
Digital I/O Module
M5302A is a single-slot Digital IO PXIe module with 28 programmable LVDS channels and 8 single-ended channels. The LVDS channels can be used to communicate to the device under test or can be used to control other devices by emulating protocols such as Camera Link. The single-ended channels are suitable for event triggers or other general-purpose IO applications.
-
Product
Grablink Full
-
For one Camera Link 80-bit, 72-bit, Full, Medium or Base configuration cameraDirectly compatible with hundreds of Camera Link cameras available on the marketECCO: Extended Camera Link cable lengthPCIe x4 bus: 850 MB/s sustained delivery bandwidthFeature-rich set of 10 digital IO linesMemento Event Logging Tool
-
Product
Framegrabber
FastXe2
-
The FastXe2 framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastXe, is a one half length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as GigEx4, high speed analog formats such as UXGA or DVI, or CoaXPress. The front-end data is formatted and preprocessed by a Kintex 7 FPGA before being sent to the PCIe (X4) Gen 2 bus
-
Product
Framegrabber
FastX3
-
The FastX3 frame grabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX3, is a one half-length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. The front-end data is formatted and preprocessed by an Artix FPGA beforie being sent to the PCIe (X4) Gen 2 interface. It also is POCL and has isolated inputs including three LVDS I/Os.
-
Product
Phoenix Camera Link Frame Grabber (D24-PE1)
AS-PHX-D24CL-PE1
-
Phoenix-D24CL is a PCI Express board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and linescan cameras. It supports all the formats of Base configuration, i.e. single 8- to 16-bit data, through 8-bit RGB, to dual tap 12-bit sources.
-
Product
PXI Frame Grabber Module
Frame Grabber
PXI Frame Grabber Modules work with any base-, medium, and full-configuration Camera Link cameras, and are ideal for many industrial, life science, and biomedical imaging applications. PXI Frame Grabber Modules support Power over Camera Link(PoCL) and can power cameras through PoCL-enabled cables. You can program the PXI Frame Grabber Module using the NIVision Development Module, or you can configure it using NIVision Builder for Automated Inspection(AI) software for faster development and simplified maintenance.
