-
product
Dual Camera Link LPC FMC
FMC-CL
Sundance Multiprocessor Technology Ltd.
The FMC-CL is a dual port camera link LPC FMC card.
-
product
Camera Link
R3-CL
The R3 frame grabber family has been designed to simplify the task of interfacing today's Camera Link cameras to a wide array of imaging applications. The R3-CL can acquire from almost every Base CL camera manufactured.
-
product
Phoenix 3U cPCI Camera Link Frame Grabber
AS-PHX-D48CL-3CPCI32-B-CR
Phoenix-D48CL is a 3U CompactPCI board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and linescan cameras. It supports all the formats of the Base and Medium configurations, i.e. single 8- to 16-bit data, through 12-bit RGB, to four tap 12-bit sources, as well as dual Base configuration, i.e. acquisition from two asynchronous Base cameras.
-
product
Cable, Power over Camera Link(PoCL),MDR to MDR,2M
199744-02
26-Pin MDR/SDR Camera Cable - The PoCL Cable provides a Power over Camera Link (PoCL) cable assembly. This cable carries power as well as signal communication for PoCL applications between compatible cameras and frame grabbers. The PoCL Cable is available in 26-Pin Mini Delta Ribbon (MDR) male to 26-Pin MDR male, or 26-Pin MDR male to 26-Pin Shrunk Delta Ribbon (SDR) male variations.
-
product
Phoenix Camera Link Frame Grabber (D48-PE4H)
AS-PHX-D48CL-PE4H
Phoenix-D48CL x4is a PCI Express board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and linescan cameras. It supports all the formats of the Base and Medium configurations, i.e. single 8- to 16-bit data, through 12-bit RGB, to four tap 12-bit sources, as well as dual Base configuration, i.e. acquisition from two asynchronous Base cameras.
-
product
Base/PoCL Camera Link frame grabber
Neon-CLB
Simplify your industrial, medical, or semiconductor imaging application with BitFlow's Neon-CLB, the easiest to use and most reliable Base/PoCL Camera Link frame grabber available anywhere. The Neon-CLB captures images at up to the camera's highest frame/data rate, with precision image acquisition suitable for the most demanding applications.
-
product
Camera Link Translators
CLT-303
The CLT-303R and CLT-303L Camera Link Translators convert RS-422 & LVDS to Camera Link, enabling the use of cameras incorporating traditional RS-422 and LVDS parallel digital interfaces with Camera Link frame grabbers. The “R” and “L” versions support RS-422 and LVDS cameras, respectively. These Camera Link converters are extremely flexible and can convert a wide range of cameras from parallel digital output to Camera Link base configuration with up-to 24-bit data.
-
product
Camera Link PXI Output Module
It is a PXI module to output as a camera link signal NTSC video signal.For outputting a trigger signal when you have the image conversion, you can ignore the delay at the time of conversion.
-
product
FireBird Camera Link Frame Grabber
AS-FBD-1XCLD-2PE4L
FireBird Camera Link Deca Low Profile is a member of Active Silicon's state-of-the-art FireBird frame grabber family. The low profile design allows the FireBird Low Profile board to be used in small embedded PC enclosures and rackmount cases where full height PC cards are not suitable. A full height bracket option of this product is available for use in standard PC form factor enclosures. FireBird is designed for ultimate performance providing the very fastest image acquisition without any CPU intervention using the latest FPGA families, DDR3 memory, and a fast Gen2 PCI Express interface.
-
product
FireBird Camera Link Frame Grabber (1xCLD-2PE4)
AS-FBD-1XCLD-2PE4
FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
product
Phoenix PMC Camera Link Frame Grabber
AS-PHX-D24CL-PMC32-B
Phoenix-Dig24CL is a PCI board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and linescan cameras. It supports all the formats of Base configuration, i.e. single 8- to 16-bit data, through 8-bit RGB, to dual tap 12-bit sources.
-
product
Phoenix PCI/104e Camera Link Frame Grabber
AS-PHX-D48CL-104PE1
Phoenix-D48CL is a PCI/104-Express board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and line scan cameras. It supports all the formats of the Base and Medium configurations, i.e. single 8-to 16-bit data, through 12-bit RGB, to 4-tap 12-bit sources, as well as dual Base configuration, i.e. acquisition from two asynchronous Base cameras.
-
product
PXIe-1435, Base-, Medium-, Full-Configuration Camera Link PXI Frame Grabber Module
781699-01
Base-, Medium-, Full-Configuration Camera Link PXI Frame Grabber Module—The PXIe‑1435 is a Camera Link image acquisition device designed for machine vision and scientific imaging applications that require high data throughput. The PXIe‑1435 works with any base‑, medium‑, and full‑configuration Camera Link camera, and it is ideal for many industrial, life science, and biomedical imaging applications. The PXIe‑1435 also supports Power over Camera Link (PoCL) and can power cameras through PoCL‑enabled cables. The onboard digital I/O includes four TTL, two optoisolated inputs, and one quadrature encoder.
-
product
Cable, Power over Camera Link (PoCL), MDR to SDR, 5M
199745-05
26-Pin MDR/SDR Camera Cable - The PoCL Cable provides a Power over Camera Link (PoCL) cable assembly. This cable carries power as well as signal communication for PoCL applications between compatible cameras and frame grabbers. The PoCL Cable is available in 26-Pin Mini Delta Ribbon (MDR) male to 26-Pin MDR male, or 26-Pin MDR male to 26-Pin Shrunk Delta Ribbon (SDR) male variations.
-
product
PCIe-1477, 80-Bit Camera Link, PoCL-Compatible Frame Grabber Reconfigurable Device
786502-01
The PCIe-1477 works well for deployment systems and features a user-programmable FPGA for onboard image processing. Placed directly in the image path, FPGAs can acquire and process images with closed-loop control without CPU intervention. This technology is also suitable for high-throughput system architectures to preprocess image data on the FPGA and then send the data to the CPU for further processing and decision-making. The PCIe-1477 also supports Power over Camera Link (PoCL), which you can use to power cameras through PoCL-enabled cables.
-
product
Accessories & Cables
Active Silicon offer a range of accessories for our hardware products, including CoaXPress and Camera Link cables and FireBird IO adapters for use with our frame grabbers. The products listed on our website are in stock and readily available. Other cable lengths or adapter types, are available on request, especially for higher order volumes.
-
product
FireBird Camera Link Frame Grabber (2xCLD-2PE8)
AS-FBD-2XCLD-2PE8
FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
product
CL PX4 SE Frame Grabber
Xcelera-CL PX4 SE
The X64 Xcelera-CL PX4 SE is a highly versatile PCIe frame grabber capable for one Camera Link™ Base, Medium, or Full camera and performing image transfers at rates up to 1024MB/s. Its low cost, combined with its ability to support multiple tap configurations from area and linescan monochrome/RGB cameras simultaneously; in addition to its onboard FPGA Bayer decoding and real-time shading correction makes the X64 Xcelera-CL PX4 SE an ideal solution to a wide variety of cost-sensitive applications.
-
product
Framegrabber
FastXe2
The FastXe2 framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastXe, is a one half length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as GigEx4, high speed analog formats such as UXGA or DVI, or CoaXPress. The front-end data is formatted and preprocessed by a Kintex 7 FPGA before being sent to the PCIe (X4) Gen 2 bus
-
product
FireBird Camera Link 3U cPCI Serial Frame Grabber
AS-FBD-1XCLD-3CPCIS-2PE4
The FireBird Camera Link CompactPCI Serial card is a member of Active Silicon’s state-of-the-art FireBird frame grabber family. FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
product
Single Sensor - Monochrome Line Scan Cameras with Fast Scan Rates
JAI’s monochrome line scan cameras provide an excellent combination of high resolution and fast scan rates.The Sweep SW-8000M-PMCL model features an 8192-pixel linear CMOS sensor delivering a line rate of 100,000 lines/s (100 kHz) over a Camera Link interface. The SW-4000M-PMCL model is based on a 4096-pixels sensor capable of running as fast as 200,000 lines/s (200 kHz) over Camera Link.
-
product
Area Scan Cameras
ace Series
Enjoy a new class of digital cameras that will help you to be even more successful and efficient at what you do. High quality and performance levels combined with a low starting list price of only 199 and a small 29 mm x 29 mm housing make Basler ace cameras one of the world''''s best-selling cameras with thousands of satisfied customers. It is available with several resolutions and speeds and with sensors from all leading manufacturers so that you can easily find the right ace camera model for your application. Choose from the most popular and standard proven data interfaces in the vision market: With the ace Gigabit Ethernet models, you benefit from our GigE market leadership, easy multi-camera setups and 100-meter cable length. Camera Link is the interface for high image data transfer. And with USB 3.0 there is an interface technology which is easy to use and real-time capable.
-
product
Digital I/O
Curtiss-Wright Defense Solutions
Our digital I/O cards include interfaces to LVDS, Camera Link, Serial interfaces, and customizable I/O. Built leveraging our decades of experience producing highly rugged COTS signal acquisition hardware, our PMC and XMC modules are designed to perform reliably in the toughest operating environments.
-
product
PCIe-1433, Base-, Medium-, Full-Configuration Camera Link, PoCL Compatible Frame Grabber Device
781169-01
The PCIe‑1433 is a Camera Link image acquisition device designed for machine vision and scientific imaging applications that require high data throughput. The PCIe‑1433 includes an onboard … FIFO for higher bandwidth use cases, and it works with any base‑, medium‑, and full‑configuration Camera Link camera. The PCIe‑1433 is ideal for many industrial, life science, and biomedical imaging applications. The PCIe‑1433 also supports Power over Camera Link (PoCL) and can power cameras through PoCL‑enabled cables.
-
product
FastCamera
FC1700
The FastCamera FC1700 is a high-speed 17 megapixel digital camera system, using a CMOS imager with an electronic global shutter, or rolling shutter. This camera has a high-speed, scalable, integrated FPGA, image processor, and memory subsystem which enables stand-alone high speed in camera image processing and extended storage. Options include ruggedized, Expanded Camera Link output, Gigabit Ethernet output, and in camera recording. When integrated with a high powered frame grabber /coprocessor board, the resulting system capabilities can be expanded by adding processors and memory on the board according to the needs of the user.
-
product
FastCamera
FC200
The FastCamera 200 is a high-speed 2 megapixel digital camera system, using a CMOS imager with an electronic global shutter. This camera has a the option of a high-speed, scalable, integrated FPGA, image processor, and memory subsystem which enables stand-alone high speed in camera image processing and extended storage. Options include back thinned versions with high QE in the visible and NIR range, ruggedized, Camera Link output. When integrated with a high powered frame grabber /coprocessor board, the resulting system capabilities can be expanded by adding processors and memory on the board according to the needs of the user.
-
product
Camera Link Adapter Module For FlexRIO
The Camera Link Adapter Module for FlexRIO supports 80‐bit, 10‐tap base‐, medium‐, and full‐configuration image acquisition from Camera Link 1.2 standard cameras. You can pair the Camera Link Adapter Module for FlexRIO with a PXI FPGA Module for FlexRIO for applications that require bit‐level processing and very low system latency. With the Camera Link Adapter Module for FlexRIO, you can use the FPGA to process images from the camera in-line before sending the images to the CPU, enabling more advanced preprocessing architectures.
-
product
Cable, Power over Camera Link (PoCL), MDR to MDR, 5M
199744-05
26-Pin MDR/SDR Camera Cable - The PoCL Cable provides a Power over Camera Link (PoCL) cable assembly. This cable carries power as well as signal communication for PoCL applications between compatible cameras and frame grabbers. The PoCL Cable is available in 26-Pin Mini Delta Ribbon (MDR) male to 26-Pin MDR male, or 26-Pin MDR male to 26-Pin Shrunk Delta Ribbon (SDR) male variations.
-
product
Framegrabber
FastX1703
The FastX1703 framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX1703, is a two thirds length raw form factor PCI board six basic 85 MHz Camera Link Channels or an extended Camera Link camera interface. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as LVDS or high speed analog formats such as UXGA or DVI. The front-end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, up to four PNX1702 500 MHz processors with 256MB memory each. Finally, the FastX1703 interfaces to the host computer through a 4xPCIe interface for state-of-the-art data acquisition.
-
product
Electro-Optical Test Software
INFRATEST
INFRATEST is a powerful software for testing IR cameras, visible and NIR cameras, ICCDs, goggles and laser rangefi nders. Based on video acquisition modules compatible with a wide range of communication protocols, including LVDS, Camera Link, GigE Vision and all types of analog formats – CCIR, PAL, RS170, NTSC, INFRATEST acquires, displays and analyzes the video signal from all types of electro-optical devices.
