-
Product
Rugged Embedded Multifunction I/O System with 10 GB Fiber Optic & 1 GB Copper Ethernet Switch
NIU3E
Multifunction I/O
The NIU3E is a small, rugged, low-power, self-contained multifunction I/O processing system preconfigured with 24-CH programmable Discrete I/O, 8-CH ARINC 429/575, 4-CH CANBus and 2-CH MIL-STD-1553 functions and incorporates an Ethernet switch module that offers four (4) 10GBase-SR multimode fiber optic ports and sixteen (16) 10/100/1000Base-T Ethernet ports. The NIU3E can also be configured with one smart Configurable Open Systems Architecture™ (COSA®) function module. The NIU3E boasts a Dual or Quad Core ARM A53 processor for customer application and I/O and communications management. The NIU3E is configured with two 10/100/1000Base-T (GbE) Ethernet ports and an RS-232 port for maintenance / diagnostic or configuration interface. Ideally suited for rugged Mil-Aero applications, the NIU3E delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
PXI Single 2 Channel Optic Mux FC/APC
40-855-012
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Fiber-Optic Transmission
-
Fiber optic transmission systems all use data links that work similar to the diagram shown above. Each fiber link consists of a transmitter on one end of a fiber and a receiver on the other end. Most systems operate by transmitting in one direction on one fiber and in the reverse direction on another fiber for full duplex operation. It's possible to transmit both directions on one fiber but it requires couplers to do so and fiber is less expensive than couplers. A FTTH passive optical network (PON) is one of the only systems using bidirectional transmission over a single fiber because its network architecture is based around couplers already.
-
Product
T7 Fiber-Optic Cable Assembly for GPIB-140, 500 m
182805-500
Cable Assembly
2-Pin Male to 2-Pin Male, Core/Clad 62.5/125 um, 850 nm Wavelength Fiber-Optic Cable for GPIB-140A Extender - The GPIB T7 Cable, sometimes referred to as GPIB Cable, connects your system to high-speed GPIB-140A extender devices. You can use the GPIB T7 Cable with a GPIB extender to increase the cable length of your system up to 1 km without comprising the integrity of your GPIB system or requiring any application modifications. The GPIB T7 Cable is offered in different lengths.
-
Product
Dual 2x2 Insert/Bypass F Optic FC/APC
40-820-022
Fiber Optic Switch
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi-mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
Product
MXI-Express Cable, Gen 1 x1, Fiber Optic, 10m
778959-10
MXI Express
MXI-Express Cable with Communication Levels up to Gen 3 x8 - The MXI-Express Cable connects a host interface to a PXI or PXI Express chassis. You can also use it for data communication between multichassis systems. NI offers it in different MXI communication levels and lengths.
-
Product
DVI Extender via Two Singlemode/Multimode Fiber Optic Cable up to 4,920 Feet
ST-2FODVI-LC
-
The XTENDEX® DVI Extender via Fiber Optic Cable locates a single link digital DVI display away from a computer up to 4,920 feet using singlemode fiber optic cable and 1,640 feet using multimode fiber optic cable. Supports resolutions to 1920x1200.
-
Product
PXI Dual 2 Channel Fibre Optic MU
40-855-322
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
LXI Dual 8:1 Optic MUX SC/PC Loop-Thru
60-850-222
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
- 10Base-T to Multimode Fiber Optic Transceiver
Model 373
-
FEATURES: Extend Lan's over 1 mile; Full Duplex Plug and Play - no software; Uses industry standard fiber optic cables; Impervious to lightning and surges; Total electrical isolation; 10Base FL compatible. Now you can break the distance barrier of Ethernet based Local Area Networks and achieve total system safety from electrical interference and surges.
-
Product
T7 Fiber-Optic Cable Assembly for GPIB-140, 1000 m
182805-01K
Cable Assembly
2-Pin Male to 2-Pin Male, Core/Clad 62.5/125 um, 850 nm Wavelength Fiber-Optic Cable for GPIB-140A Extender - The GPIB T7 Cable, sometimes referred to as GPIB Cable, connects your system to high-speed GPIB-140A extender devices. You can use the GPIB T7 Cable with a GPIB extender to increase the cable length of your system up to 1 km without comprising the integrity of your GPIB system or requiring any application modifications. The GPIB T7 Cable is offered in different lengths.
-
Product
PXI Dual 2 Channel Optic Mux FC/PC
40-855-022
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Fiber Optic Sensing Interrogator
RTS250+
-
This unit provides users with up to 200 Hz sampling rate for up to 4 fibers, which is twice the speed of our proven RTS125+, the unit that was created in partnership with NASA to support the test and validation of their new vehicles.
-
Product
Dual 2 Channel Fibre Optic Mux SC/PC
40-815-222
Fiber Optic Switch
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi-mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
Product
RS-232, RS-422, or RS-485 to Fiber Optic Line Driver
Model 8277
-
The Model 8277 is a unique asynchronous fiber optic modem whose optical interface can operate in either point to point or ring (daisy chain) configurations and whose electrical interface can also operate in point to point or multi-drop configurations depending on the user selected interface.
-
Product
EDFA Optic Amplifiers
-
Wuhan Sunma Technology Co., Ltd.
With the feature of high input power, high output power, and medium optical gain, the booster amplifier operates at the transmission side of the link to amplify aggregated optical input power for reach extension.SunmaFiber booster amplifier is a low-noise, gain-flattened C-band optical erbium doped fiber amplifier (EDFA) designed to cost-effectively extend the optical link power budget for building long distance DWDM solutions.SunmaFiber also offers switches, routers and fiber converters including 10/100M, 10/100/1000M and 10G fiber converters, SFP fiber converters, manageable/unmanageable fiber converters, OEO fiber converters, POE fiber converters, fiber converter cards, and fiber converter chassis; transmitting distance from 2km(MM) to 150km(SM) with SC or LC or FC connectors.
-
Product
PXI Single 2 x 2 Fibre Optic Mux MU
40-860-312
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
-
Product
FluorOptic Fiber Optic Temperature Sensors
-
Advanced Energy’s Luxtron® Fiber Optic Temperature Sensors enable customer innovation in complex applications for a wide range of industries including semiconductor equipment, industrial, manufacturing, telecommunications, data center computing, and medical. Based on Fluoroptic® technology, each individual product can be configured for specific applications.
-
Product
(9 PCS) 8 Noid Light Kit With Fiber Optic Noid Light Extension
3621A
-
Peaceful Thriving Enterprise Co Ltd
*Kit packs in a deluxe molded plastic case.*Set includes: 8 Noid lights for testing GM PFI, FORD TBI, GEO TBI, BOSCH PFI, GM TBI, GM SCPI, GM MULTEC 2 and BOSCH 2.*Plus one fiber optic Noid Light extension.
-
Product
UFP series High Sensitivity Fiber Optic Alignment Stages
UFP
-
Model: UFP1A-LFeatures:• The linear stage has both coarse adjustment and fine adjustment, sensitivity is much better than 0.5um• The rotation stage sensitivity is much better than 23.4" • High stability
-
Product
RS232 / RS485 / RS422 To Fiber Optic Converters
-
Our rugged, industrial-grade, point-to-point RS232 / RS485 / RS422 serial to fiber optic converters work in pairs to extend serial signals (RS232, RS485, RS422, and TTL) over long distance. These point-to-point RS232 / RS485 / RS422 serial to fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of multi-mode (extend distance up to 3 miles / 5km) and single-mode (extend distance up to 25 miles / 40 km), and ST, SC, and FC connectors.
-
Product
CATV Fiber Optic Receiver
MX862R
-
The MX862R is a Fiber Optics Receiver used to convert a fiber optic connection to RF (coax output).
-
Product
PXI Quad 2 Channel Fibre Optic MU
40-855-342
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
PCI-8366, PCI Host, 100 MB/s, Fiber-Optic Cable MXI-Express Device for PXI Remote Control
781400-01
Remote Control Interface
The PCI‑8366 is an MXI‑Express remote controller for devices or systems over cabled PCI from a computer with a PCI slot. The PCI‑8366 remote controller provides a PCI link over a fiber-optic cable to the PXI‑8368 remote control module when used for PXI system control. Fiber-optic remote control solutions are ideal for long‑distance‑device control and electrical isolation. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
Product
PXI Single 4 Channel Fibre Optic Mux FC/PC
40-850-114
Fiber Optic Switch
The 40-850-114 4-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
PXI Single 4 Channel Fibre Optic Mux SC/PC
40-850-214
Fiber Optic Switch
The 40-850-214 4-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Fiber Optic Temperature Sensor with the EasyDisk
The TPT-62
-
The TPT-62 fiber-optic temperature probe family employs industry standard 62.5µm core OM1 fiber optic for highly improved optical, mechanical, and reliability properties over legacy 200 µm core (1st generation) fiber optic sensors. The EasyDisk sensor tip assembly ensures IEC60076-2 (Annex E) compliant installation and enables quick insertion of the probes into the spacers within the windings of transformers.
-
Product
Omega Fiber Optic Connector
-
Teledyne lmpulse-PDM's Omega Series offers any combination of multi-mode or single-mode optical ways and 16 AWG electrical ways from a single way through to seven ways. Electrical pins are part of the CCP and the mating sockets are part of the FCR, CCR or BCR. Connectors populated with both electrical and optical ways will be populated in a standard Teledyne lmpulse-PDM format to facilitate interchangeability between batches. This information can be provided at the time of quotation.
-
Product
PXI Single 8 Channel Optic Mux FC/PC
40-852-118
Fiber Optic Switch
The 40-852-118 8-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
