Modbus
communications protocol for sharing data between controllers.
See Also: Communication Protocol, Near Field Communications, Data Communications, Modbus RTU
-
Product
Modbus I/O extender
CoolEx
-
CoolEx is a Modbus I/O extender with analog, digital and PWM inputs and outputs. CoolEx can be used in conjunction with Programmable Logic Controller (PLC) or any other Modbus master that requires some extra I/O or special I/O functionality. CoolEx is controlled by master by means of standard Modbus requests defined in "Modbus Application Protocol Specification".
-
Product
Modbus TCP Redundant Ethernet I/O
-
ICP DAS USA's RIO-9380 is a Modbus TCP based Ethernet-based Data Acquisition Rack that supports redundant communication and redundant power for maximum uptime. Our Redundancy Ethernet I/O Racks provide a scalable, open architecture that bridges factory-floor hardware with enterprise IT systems. Designed for mission-critical reliability, these racks support redundant communication paths to ensure the system remains operational during network or power fluctuations..
-
Product
Smart Protocol Analyzer
-
Works transparently over the Computer's I/O ports (serial & network). The analyzer supports Modbus, Fisher-ROC, BSAP, DNP and other Protocols. In addition to monitoring, this tool is capable of simulating Master and Slave devices.
-
Product
Low Power Wireless Gas Detector
CX
-
Teledyne Gas & Flame Detection
Model CX sensors are equipped with standard analog 4-20mA, and Modbus™ RTU RS-485 outputs and can be used with SmartWireless Site Sentinel CX/CXT controllers. The CX is a very low power device making it an ideal choice for a battery powered detector (optional) in applications where power is unavailable or not economically feasible.CX gas detection sensors are easily and economically deployable in both permanent and temporary installations. These low power sensor assemblies utilize electrochemical technology for a long list of toxic gases.
-
Product
4 Digit Temperature Meter (5 Channels)
CM1-TX5
-
RS-485 Modbus RTU protocol (with communication LED indicator)RS-485 address 1~255Communication Baudrate 9600, 19200, 38400, 57600, 115.2KParity check N81, N82, E81, O81Input 5 channels of signal selectable：thermocouple/PT100.5 channels of input can be set to play 1~10 seconds loop display.1~5 channels of display value limits can be set, and the number of channels of carousel display screens can be set by yourself.5 channels of input signals with LED unit cycle display.Standard 2 groups of alarms Hi, LO with communication LED indicators to ensure the normal operation of the field system.Suitable for HVAC refrigeration and air conditioning PLC, DDC, PC brands to achieve remote real-time monitoringCan be used in solar panels, medical control, clean room, ice water host, boiler, motor, chemical plant, power plant, school energy-saving control, remote control of power monitoring panel
-
Product
OPC UA Ethernet I/O Modules
ADAM-6300
-
Industrial OPC UA Ethernet I/O Modules with Modbus protocol converge OT/IT with security, linking to SCADA and the cloud for remote monitoring.
-
Product
16-Port +2 SFP Entry-Level Switch Supporting Modbus TCP/IP
EKI-5726FI-MB
-
Entry-Level Managed Switch, Provides wide operating voltage 8.4~52.8 VDC, C1D2 and ATEX certified for horizontal area. IXM function enables fast deployment, Modbus/TCP Enabled by default, Supports X-Ring for ultra high-speed recovery time less than 20ms.
-
Product
Combustible Monitor
SMC 5100-02-IT
-
The SMC 5100-02-IT gas sensor monitors combustible gases such as Methane, Hydrogen, Propane, and others. It is based on catalytic bead technology, a consistent and reliable method of detection that offers excellent response times to the target gases. The 5100-02-IT sensor offers multiple communication outputs including 4-20 mA and Modbus RTU.
-
Product
TM Series Tiny DCON & Modbus RTU Data Acquisition Modules
-
The tM Series tiny compact modules communicate over Modbus RTU and DCON protocols and provide Analog and Digital I/O functions like isolated digital input, relay and open-collector output. They easily integrate with HMI, SCADA, PLC’s and other systems. They are equipped with two removable terminal block connectors for easy wiring.
-
Product
TM Series Tiny DCON & Modbus RTU Data Acquisition Modules
-
The tM Series tiny compact modules communicate over Modbus RTU and DCON protocols and provide Analog and Digital I/O functions like isolated digital input, relay and open-collector output. They easily integrate with HMI, SCADA, PLC’s and other systems. They are equipped with two removable terminal block connectors for easy wiring.
-
Product
Industrial Automation
-
PLANET Industrial Automation solution is designed to help set up IP networking in the areas of Industrial 4.0 and IoT using the serial port connection. Our Industrial Automation product line includes RS232/RS422/RS485 Serial Device Servers, Modbus Gateways, EtherCAT Slave I/O Modules and Serial over Cellular Gateways, each of which enables to convert and transform useful data for further analysis to optimize factory operation and management.
-
Product
Digital Panel Meter
VAM
-
VAM Voltage & Current Meter has been designed with high accuracy dual channels(isolated) measurement, dual display and communication of 0~600V and 0~10A for DC/AC/TMRS. In compact size(48 x 96mm)● Build in mathematic function such as Addition / Subtraction / Multiplication / Division / high or low selector in 2 channels input to meet various testing equipment inquiry.They are also build in 4 Relay outputs, 1 Analogue output and 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of industrial applications.
-
Product
Industrial 4-Port Modbus Gateway
EKI-1224
-
Supports surge protection for D.C. power ports with line to line 2 KV, and line to earth 4 KV; for signal ports with 4 KV. Provides 2 x 10/100 Mbps Ethernet ports for LAN redundancy. Integration of Modbus TCP and Modbus RTU/ASCII networks.
-
Product
5 Digit Programmable Speed/Velocity Meter
CM1-RL
-
CM1-RL series provides a simple economic programmable speed/velocity table, it 20.0mm, 5-digit LED display, press the key to set the display range and its anti-jamming design and reliable quality, simple installation, you can meet the needs of general measurement of speed/velocity.This instrument also has 2 group relay outputs, 1 analog output, or 1 groups RS485 (Modbus RTU mode) communication features three a (More features please refer to page description). Operation press the inner design, the more human-no action can be avoided, especially suitable for all kinds of machinery used.
-
Product
Multi-Circuit Power Meter (DIN rail) (ADPower Series)
ADP-PM-A
-
The ADP-PM-A was designed for multi-circuit power measurement, up to 12 single phase or 4 three-phase circuit power inputs. Applicable to different types of power circuit makes ADP-PM-A a valuable option.Hardware built in 1 RS485 (Modbus) communication port, demand function, data logging and 2MB Flash memory.At the same time, din rail mounting provides easy installation and larger flexibility.
-
Product
Modbus or Laurel ASCII ProtocolSerial Output DIN Rail Transmitters
-
Laureate TM Series serial output transmitters can be jumpered for two signal levels: RS232 or RS485. Two serial protocols are selectable in software: Modbus or Laurel's Custom ASCII.Modbus protocol operation is fully compliant with the Modbus Over Serial Line Specification V1.0 (2002) for 2-wire, half-duplex connection.
-
Product
1-Port Modbus Gateway
EKI-1211
-
1 x 10/100 Mbps Ethernet port Integrates Modbus TCP and Modbus RTU/ASCII networks. Baud rate: supports up to 230.4 Kbps. Supports up to 16 connections per serial port under Modbus client mode and 32 sessions under Modbus server mode.
-
Product
Multifunctional Meter
CPM-70
-
CPM-70 multifunction power analyzer provide high accuracy single phase and three-phase energy measuring and displaying, energy accumulating, power quality analysis, data logging and data communication.CPM-70 series meters are able to measure bidirectional, four quadrants kWh and kVarh.It provides maximum/minimum records for power usage and power demand parameters. Hardware standard built in a RS485 Modbus communication port , 4 Digital inputs, 2 Relay outputs, LCM and 2 MB flash for data-logging.
-
Product
Analyzers
-
for analysis and optimizing of all RS232 and RS422/485 field-bus connections. It gathers exact information about every line change with 1µsec precision – indispensable for each analysis of time depending protocols like Modbus RTU, Profibus or similiar.
-
Product
Multifunctional Meter
CPM-80
-
CPM-80 multifunction power analyzer provide high accuracy single phase and three-phase energy measuring and displaying, energy accumulating, power quality analysis, data logging and data communication. CPM-80 series meters are able to measure bidirectional, four quadrants kWh and kVarh. It provides maximum/minimum records for power usage and power demand parameters. Hardware standard built in a RS485 Modbus communication port , 4 Digital inputs, 2 Relay outputs, LCM and 2MB flash for data-logging. In addition , also provide TOU , voltage and current THD, harmonics up to the 63rd and auto wiring change via software .
-
Product
CAS Modbus Scanner
-
CAS Modbus Scanner is a utility to retrieve coils, inputs, holding registers, and input registers from a Modbus enabled device. Values retrieved from the device can be viewed in many different formats including Binary, HEX, Uint16, Int16, Uint32, Int32, and Float32. This utility can also discover Modbus devices on your network if you do not know their address. It works by testing every address, function, length, offset to check for exceptions or responses.
-
Product
4 2/3 Digits Voltage/Current Meter
CS2-VA
-
CS2-VA Voltage/Current Meter is designed with high accuracy measurement, display and communication of 0~600V or 0~10A for DC/AC/TMRS.● ADTEK builds flexible function as like as 3 bank (for multi-range scaling and set point) and 3 external control inputs meet to various testing equipment inquiry.They are also build in 4 Relay outputs, 3 External Control Inputs, 1 Analogue output and 1 RS485 (Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of industrial applications.
-
Product
Gas Monitors with X3® Technology
Ultima® X
-
The Ultima X Series Gas Monitors with X3 Technology bring the power of multi-sensing, signal boost and ModBus output to the Ultima X line of MSA gas monitors. The units are crafted from either stainless steel or NEMA 4X-rated plastic, and our patented SafeSwap sensor disconnect-underpower feature allows all sensors to be replaced in hazardous areas without area declassification.
-
Product
10 Digit Rate/Batch Counter
CS2-MC
-
The CS2-MC provides dual input(A/B phase) and display with high speed, counting, control and communication (Modbus RTU mode) of Pulse from encoder, proximity switch, photo switch or flow meter for counting, length and position control. There are 3 external control input (DI) in standard and the optional 4 Relay, 1 Analogue, and RS485 port available.The relays are also support N, C, R, E mode and Hi/Lo energized for batch / totalizer and position control.
-
Product
Process Indicator
CS2-PR
-
CS2-PR Process Indicator has been designed with high accuracy measurement, display and communication of DC signal 0~10V and 4(0) ~20mA with square root function.They are also build in 4 Relay outputs, 3 External Control Inputs, 1 Analogue output and 1 RS485 (Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of industrial applications.
-
Product
Signal Conditioners & Interface
-
Modbus RTU Remote Connectivity and Control. Minimize Long Cable Runs with Modbus Network. Pulse to Frequency Conversion. Shaft Speed Pulse to DeviceNet. Shaft Speed Pulse to 4-20 mA Conversion.Sensor Compatibility
-
Product
Modbus Register Converter - Serial To Modbus RTU Interface
-
Translates Modbus registers and variable types from an older Modbus devices to a new Modbus device. The Model 2390 allows upgrading Modbus RTU devices without changing the system software. The 2390 also provides serial control of Modbus RTU devices for new applications that want the ease of using simple ASCII commands strings when controlling Modbus RTU devices.
-
Product
Flow Monitor
B2900
-
Blancett B2900 flow monitor offers advanced digital signal processing technology in an easy-to-access package. Enclosed in a spacious polycarbonate NEMA 4X housing, the electronics are located on a single board, designed for straightforward and convenient field installation. The B2900 enclosure features an LCD display with push button programming as well as a pre-drilled hole for external wiring connections, such as Modbus RTU and other outputs.
-
Product
Master And Slave
Smart I/O
-
An I/O server is a software which controls and monitors one or more PLCs /RTU's using various communication protocols.Our I/O servers are built on highly optimized Windows 32bit platform. They are capable of handling very large scale SCADA systems with minimal impact on CPU usage, resulting in effective timing and usage of available hardware.Currently, we have Master and Slave solutions for DNP3 and Modbus (ASCII, RTU, TCP). Please select the appropriate tab above for more informaiton.If you are looking for a specific I/O Server, please contact us with your needs.
-
Product
OPC Server
-
An OPC sever (OLE for Process Control) provides IO and more devices to communicate with a wide range of HMI/SCADA software packages residing on a host. Advantech''s OPC server for ADAM and modbus devices features OPC DA (data access) and AE(alarm and events) client for the rapid testing.
